• 전력전자학회논문지
• /
• 제25권1호
• /
• pp.54-60
• /
• 2020

A digital current control scheme using virtual d-q transformation for a boost single-phase power factor correction (PFC) converter is proposed. The use of virtual d-q transformation in single-phase power converters is known to improve current control performance. However, the conventional virtual d-q transformation-based digital current control scheme cannot be directly applied to the boost single-phase PFC converter because the current and average voltage waveforms of the inductor used in the converter are not sinusoidal. To cope with this problem, this study proposes a virtual sinusoidal signal generation method that converts the current and average voltage waveform of the inductor into a sinusoidal waveform synchronized with the grid. Simulation and experimental results are provided to show that the virtual d-q transformation-based digital current control is successfully applied to the boost single-phase PFC converter with the aid of the proposed virtual sinusoidal signal generation method.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.32-32
• /
• 2009

Electric Resistance Welding (ERW) process is the most efficient process to manufacture the linepipe. To develop the high performance ERW linepipe using the high strength and the high alloy steels, the modulation of input power waveform such as sinusoidal waveform is introduced because the conventional ERW technology is not sufficient enough to produce the high quality linepipe due to its strength and high alloy contents (high Ceq). In this article, the material used for the experiment was API X60 with 8.2mm thickness, and ERW simulator at POSCO was used to develop a waveform control system for the power modulation. The frequency of power modulation was varied from 50Hz to 150Hz with the fixed amplitude of ${\pm}2%$ power. The non-modulated power input and the modulated power input cases are conducted to demonstrate the variation of the narrow gap length and the arcing frequency due to power modulation. From results of the non-modulated power input case, the excessive power causes the longer narrow gap length and the low arcing frequency due to the large heat input and the strong electro magnetic force that increase the weld defect. On the contrary, the small narrow gap length and the high arcing frequency reduce the weld defect. After modulating the power input with 50Hz and 100Hz at the fixed power, the arcing frequency increases, but the narrow gap length does not change much. The high arcing frequency prevents the formation of weld defect because the sweeping frequently cleans the oxides on the narrow gap edges. As a result, the manufacturing window can be expanded by the power modulation that provides the stable ERW process for the quality improvement of the linepipe made from the high strength/high alloy steels.

• Journal of Power Electronics
• /
• 제15권5호
• /
• pp.1207-1216
• /
• 2015

In order to suppress the low frequency oscillation of the neutral-point voltage for three-level inverters, this paper proposes a new discontinuous pulse width modulation (DPWM) control method. The conventional sinusoidal pulse width modulation (SPWM) control has no effect on balancing the neutral-point voltage. Based on the basic control principle of DPWM, the relationship between the reference space voltage vector and the neutral-point current is analyzed. The proposed method suppresses the low frequency oscillation of the neutral-point voltage by keeping the switches of a certain phase no switching in one carrier cycle. So the operating time of the positive and negative small vectors is equal. Comparing with the conventional SPWM control method, the proposed DPWM control method suppresses the low frequency oscillation of the neutral-point voltage, decreases the output waveform harmonics, and increases both the output waveform quality and the system efficiency. An experiment has been realized by a neutral-point clamped (NPC) three-level inverter prototype based on STM32F407-CPLD. The experimental results verify the correctness of the theoretical analysis and the effectiveness of the proposed DPWM method.

• 한국산학기술학회논문지
• /
• 제14권11호
• /
• pp.5906-5914
• /
• 2013

최근 국내에서 철도부지 상부에 인공지반을 구축하고, 인공지반 위에 복합주거타운을 건설하는 정책이 추진되고 있다. 이에 상부 구조물 및 인공지반을 지지할 수 있는 적합한 기초형식이 요구되는데, 철로와 철로 사이의 좁은 공간에 급속 시공 가능한 기초 형식 중 가장 대표적인 방법은 마이크로파일로 알려져 있다. 그러나 주기초로 마이크로파일이 사용될 경우 기초 시공비가 크게 증가하게 된다. 따라서 본 연구에서는 마이크로파일의 경제성 및 지지력을 향상시키면서 철도상부 인공지반에 적합한 신개념 마이크로파일을 제안하였다. 신개념 마이크로파일은 지반을 Jet Grouting 공법을 이용하여 지반의 일정 영역을 고결시킨 뒤 강봉을 시공하는 방법에 Jet Grouting 시 말뚝체를 파형(waveform)의 형상으로 시공하여 지지력을 향상시키고 기존 마이크로파일 대비 말뚝의 전체 길이를 줄여 경제성을 높이고자 한 방법이다. 본 연구에서는 2차원 축대칭 유한요소해석을 수행하여 이러한 파형 마이크로 파일의 지지거동을 분석하였다. 해석 결과 파형 마이크로파일은 일반 마이크로파일에 비해 길이가 15% 정도 감소하였음에도 불구하고 동일한 설계하중에서 변위가 감소하여 지지력 및 경제성 측면에서 효과가 있는 것으로 나타났다. 또한, 파형 마이크로파일의 요철에 의한 주면 마찰력 증가효과는 상대적으로 연약한 토층에서 큰 것으로 나타났다.

• Journal of Electrical Engineering and Technology
• /
• 제11권1호
• /
• pp.241-246
• /
• 2016

This paper presents a method that can improve the performance of permanent magnet synchronous motor current control by minimizing the measured current phase delay caused by the Low Pass Filter(LPF) used to cut off the noises that flowed in when feedback currents are measured. Although existing methods that change the Cutoff Frequency of the LPF can minimize phase delays during high speed rotations, their noise cutoff effects are much lower and this may lead to the decline of control performance. Therefore, in this study, an algorithm that can compensate current phase delays through relatively simple calculations from the synchronous motor d-q axis coordinate transformation matrix and the inverse transformation matrix is proposed and the validity of the proposed method is verified by comparing the waveform of the calculated current with the waveform of actual currents through simulations and experiments.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1991년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 22-24 Oct. 1991
• /
• pp.917-921
• /
• 1991

Hydraulic fitting impulse tester is equipment which produce impulse pressure waveform that specified foreign standard of SAE, JIS etc. Test conditions of SAE J1453 about waveform standard indicates frequency of 35-70 cycle/min, pressure of 560 bar, oil temperature of 93 .+-.3.deg. C etc. and required cycle is a million over. In additions, Test condition operated continuously equipment. This development item adopted new pattern method such as intensifier and rotary distributor is different from already established fitting impulse tester applied servo valve and high pressure direct directional control valve. Therefore, this development item which compares already established item is good reliability, low cost of manufacture and save of electric energy. especially, Domestic small and medium enterprise uses this tester because of economical cause. We develope appropriateness tester which conforms to demand of user.

• Journal of Electrical Engineering and Technology
• /
• 제3권2호
• /
• pp.162-166
• /
• 2008

This paper presents the design and implementation of a 5kW programmable three-phase harmonic generator, which is capable of generating sinusoidal output voltages with adjustable output amplitude and frequency over a wide range as well as arbitrary waveforms. The considered harmonic generator is a linear power amplifier type. This system consists mainly of a power converter to generate and amplify waveform signals, a controller to control the desired output signal and measure the output parameters including voltage and current, and a control program to set the desired output and display the output values. The prototype programmable three-phase harmonic generator has been constructed and tested. Test results show that the developed programmable three-phase harmonic generator performs well.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 학술대회 논문집 전문대학교육위원
• /
• pp.12-15
• /
• 2002

This propose a simple DC voltage sensor less single phase PFC(Power Factor Correction Circuit) converter by detecting a AC current sensors are not required to construct the control system. The DC voltage is directly controlled by the command input signal Kd($V_o/V_a$)for the boost chopper circuit. The DC voltage regulation is small because of the feed forward control for the AC line voltage VS and no dependence of the circuit parameters. The sinusoidal current waveform in phase with the AC input voltage can be obtained. These characteristics are confirmed by some experiment results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 학술대회 논문집 전문대학교육위원
• /
• pp.166-171
• /
• 2002

We are in transitional period of welding technique, which has changed from the stage of quantity and quality to the stage of future technique, imported and introduced from many advanced countries. Therefore, many researches and studies for development on high speeding and making welding machines with high effectiveness has been doing vigorously. In this dissertation, I have studied on a pulsed MAG welding machine, with which welding of thin plates may perform high speeding and effecting. First, I produced a phase shifted full bridge DC-DC convert, which is the type of reduced conduction loss and the power supply for welding machine. And then, I found out an output waveform control algorithm about one pulsed one droplet and short waveform control for thin plates with high speed by deriving the circuit model utilizing the circuit averaged method for full bridge converter.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2007년 추계학술발표대회 개요집
• /
• pp.291-293
• /
• 2007