• Journal of Ocean Engineering and Technology
• /
• v.36 no.1
• /
• pp.1-10
• /
• 2022

Recently, as the offshore structures are operated in the deep-sea oil fields, interest in the analysis of relative wave elevation around platforms is increased. In this study, it is examined how the analysis results differ depending on the characteristics of the wave probe when interpreting the relative wave elevation in the model test. First, by conducting the wave probe comparison experiment in the two-dimensional wave tank, it is confirmed how the measured values differ according to the type of wave probe for the same physical phenomenon. Two types of wave probe are selected, the resistance type and the capacitance type, and the causes of the difference in measured values is studied. After that, the model test of the semi-submersible platform is conducted to investigate the relative wave elevation. Relative wave elevation is measured with the wave probes used in the wave probe comparison experiment and analyzed to estimate the asymmetric factor and the extreme upwell. The results between the two types of wave probes are compared, and qualitative study for the cause of the difference is conducted by photographing the physical phenomenon using a high-speed camera. Through the above study, it is confirmed that the capacitance type wave probe shows a larger measured value than the resistance type under the breaking-wave condition, and the same results are obtained for the asymmetric factor and the extreme upwell. These results is thought to be due to the difference in the measurement principle between wave probes, which is whether or not they measured water bubbles. This implies that the model test should be conducted using appropriate wave probes by considering the physical phenomenon to be analyzed.

• Journal of Welding and Joining
• /
• v.14 no.6
• /
• pp.37-47
• /
• 1996

An ultrasonic testing uses the directivity of the ultrasonic wave which propagates in one direction. The directivity is expressed as the relationship between the propagate direction and its sound pressure. The directivity of ultrasonic wave is related to determination of testing sensitivity, scanning pitch and defect location. This paper investigated the directivity of ultrasonic wave, which scattered from slit defect located in heat-affected zone (HAZ) in butt joint using visualization method. The directivity of shear waves scattered from slit defect were different according to probe direction (far defect, near defect) and probe position (forward movement, maximum echo position, backward movement). The difference of directivity of reflection wave was existed between 2 MHz and 4 MHz angle probes. In the case of 2 MHz angle probe, the directivity of reflection wave was appeared sharp form because of the relation wave length and defect size.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.119-126
• /
• 2008

Ground stiffness(shear wave velocity) is one of the key parameters in geotechnical earthquake engineering. An In-situ seismic technique has its own advantages and disadvantages over the others in stiffness measurements. By combining the crosshole and seismic cone techniques and utilizing favourable features of bender elements, a new hybrid probe has been developed in order to enhance data quality and easiness of testing. The basic structure of the probe, called "MudFork", is a fork composed of two blades, on each of which source and receiver bender elements were mounted respectively. To evaluate the disturbance caused by the penetration of the probe, shear wave velocity measurements were carried out in the Kaolinite slurry in the laboratory. Finally, the probe was penetrated in coastal mud near Incheon, Korea, using SPT(standard penetration test)rods pushed with a routine boring machine and shear wave velocity measurements were carried out. The results were verified with data from laboratory and cone testing. The performance of the probe turns out to be excellent in terms of data quality and testing convenience.

• Journal of the Optical Society of Korea
• /
• v.12 no.3
• /
• pp.192-195
• /
• 2008

We report on the spatial information of a coupling laser transfer into a reflected probe laser; the transfer is achieved by means of electromagnetically induced transparency through a common excited state connected with $5S_{1/2}-5P_{1/2}(F=1{\rightarrow}F'=2)$ in the $^{87}Rb\;D_1$ line. When the coupling laser was spatially modulated as a stationary wave, the absorption of the probe laser was enhanced and the reflection of the probe laser was generated. When the coupling laser was spatially modulated by a mask, we observed that the reflection light of the probe laser was modulated as the shape of the mask. The Bragg reflection transferred the spatial information of the coupling laser. The reflection was approximately 7% of the incident power of the probe laser.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.30-30
• /
• 2011

The wave-cutoff tool is a new diagnostic method to measure electron density and electron temperature. Most of the plasma diagnostic tools have the disadvantage that their application to processing plasma where toxic and reactive gases are used gives rise to many problems such as contamination, perturbation, precision of measurement, and so on. We can minimize these problems by using the wave-cutoff method. Here, we will present the results obtained through the development of the wave-cutoff diagnostic method. The frequency spectrum characteristics of the wave-cutoff probe will be obtained experimentally and analyzed through the microwave field simulation by using the CST-MW studio simulator. The plasma parameters are measured with the wave-cutoff method in various discharge conditions and its results will be compared with the results of Langmuir probe. Another disadvantage is that other diagnostic methods spend a long time (~ a few seconds) to measure plasma parameters. In this presentation, a fast measurement method will be also introduced. The wave-cutoff probe system consists of two antennas and a network analyzer. The network analyzer provides the transmission spectrum and the reflection spectrum by frequency sweeping. The plasma parameters such as electron density and electron temperature are obtained through these spectra. The frequency sweeping time, the time resolution of the wave-cutoff method, is about 1 second. A short pulse with a broad band spectrum of a few GHz is used with an oscilloscope to acquire the spectra data in a short time. The data acquisition time can be reduced with this method. Here, the plasma parameter measurement methods, Langmuir probe, pulsed wave-cutoff method and frequency sweeping wave-cutoff method, are compared. The measurement results are well matched. The real time resolution is less than 1 ?sec. The pulsed wave-cutoff technique is found to be very useful in the transient plasmas such as pulsed plasma and tokamak edge plasma.

• Journal of the Society of Naval Architects of Korea
• /
• v.60 no.5
• /
• pp.305-319
• /
• 2023

This study focuses on measuring the relative wave elevation around the KSUPRAMAX-O ship and comparing it with numerical analysis results (potential and computational fluid dynamics). The relative wave elevation is a good indicator of the pressure distribution on the ship's surface, which is affected by the ship's motion, incident waves, and distributed waves. Prior to measuring the relative wave elevation, a comparative test was conducted on resistance type, capacitance type, and ultrasonic type wave probe to measure the relative wave elevation, and it was confirmed that the resistance type wave probe was suitable for measuring the relative wave elevation. A model test was performed at low speed and design speed using resistance type wave probe and compared with the results of numerical analysis result. As for the motion response, it was confirmed that the result of experiments and the result of the numerical analysis were in good agreement. The relative wave elevation showed a similar trend between the experiment and the computational fluid dynamics, but the potential analysis result showed a difference from the experiment in design speed.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.1
• /
• pp.30-35
• /
• 2004

We have carried out a basic experiment in order to develope a super high-resolution optical microscope which transcend the limitation of diffraction and the wavelength of lightwave. The image of this scope is composed by measuring the evanescent wave which is localized on the surface of the testing materials. A detecting probe was fabricated with a single mode optical fiber to be sharpened by the chemical etching, and drived by PZT. The standing wave of $0.33\mu\textrm{m}$ wavelength evanescent wave which was generated from the $0.78\mu\textrm{m}$-wavelength semiconductor laser was detected by the $0.5\mu\textrm{m}$-thickness optical fiber probe.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.9 no.1
• /
• pp.39-47
• /
• 1989

As the necessity of the safety diagnosis of the concrete structure, more reliable ultrasonic technique to qualify the concrete is required. In this study, the artificial surface crack depth is measured using several types of the ultrasonic probes. As results, the horizontal shear wave probe is most useful to determine the crack depth compared to the other probes. For the surface wave probe, the ultrasonic wave path is changed with the surface crack depth.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.32 no.2
• /
• pp.185-191
• /
• 2012

Typically, a wedge is involved to generate effectively high inspection angle in pipe weld inspection using phased array ultrasonic technique. But the usage of this wedge for weld or access limited area can cause coverage limitation for the examination volume because of the wedge front length. Therefore, the shear wave phased array probe which can generate high inspection angle without wedge is essentially necessary. In this paper, the shear wave phased array ultrasonic probe which can generate high inspection angle designed by modeling and manufactured from the modelling result. And this shear wave probe tested whether it can detect and sizing for EDM test block that contains various depth. As results, the experimental results show that the designed shear wave phased array probe can detect and size with reliable accuracy. Therefore if this phased array probe apply in field inspection, it is expected that it show more reliable inspection result for plant structure having access limitation.

• The Journal of Engineering Geology
• /
• v.23 no.4
• /
• pp.511-517
• /
• 2013

The Field Velocity Probe (FVP) has been widely applied to determine the various characteristics of soils. This study seeks to estimate soil consolidation characteristics using an FVP and to increase its application in the field. The specimens were extracted from depths of 3 and 6 m at the study site, an area of soft clay in Incheon. In laboratory testing, the specimens were placed in an improved oedometer cell to measure shear wave velocity, and statistical analysis was performed to compare the results of effective stress and shear wave velocity. FVP enables increased resolution in the field because it measures the shear wave velocity every 20 cm. To estimate the condition of consolidation, we compared the results of shear wave velocities between those obtained in the laboratory and those in the field. The field conditions are used to analyze overconsolidated and normally consolidated soils at depths of 3 and 6 m, respectively. The results show that FVP is a suitable method for estimating the degree of consolidation.