• 한국화재소방학회논문지
• /
• 제32권4호
• /
• pp.17-24
• /
• 2018

본 논문은 화재의 발생 및 전파를 억제하기 위해 방수총의 내부 유체유동특성을 파악하는 것을 목적으로 한다. 본 연구를 위해 개발 중인 워터노즐을 모델링하였고, 필드실험에서 얻은 경계조건(펌프의 가압력 : 4 bar, 방수총 출구압력 : 대기압)을 적용하였으며, 유동에 대한 운동량 지배방정식을 이용하여 방수총 내부 유동에 대한 속도 및 압력분포를 얻었다. 서브파이프의 유무와 길이를 기준으로 방수총 출구의 노즐에서의 성능 특성에 영향을 미치는 2가지 주요 인자로 고려하였다. 해석 결과 기존 모델의 경우에는 서브파이프의 길이가 변하더라도 방수총의 출구영역에서 성능특성에 그다지 영향을 미치지 않았다. 이에 반해서, 서브파이프를 단관형으로 교체한 경우에는 서브파이프의 입구에서 역류가 발생하였고, 이를 제거하기 위해 서브파이프의 길이를 2배로 변화시켜 역류를 제거할 수 있었다.

• 한국터널지하공간학회 논문집
• /
• 제23권6호
• /
• pp.589-604
• /
• 2021

워터젯 암반 굴착공법은 물과 연마재만을 사용하는 친환경 및 비접촉식 굴착방법으로 다양한 장점을 가지고 있다. 최근에는 기존 천공 공법의 문제점을 보완하고 분진 방지, 소음 저하 등의 이유로 워터젯 공법의 활용이 증가하고 있다. 워터젯 굴착효율을 증대시키기 위해서는 복수의 노즐을 운용하는 것이 유리하다. 복수의 노즐을 사용할 경우, 노즐 운용방법에 따른 굴착성능과 형상을 분석하는 것이 필수적이다. 본 연구에서는 노즐각, 노즐 간 수평거리, 이격거리를 노즐 운용변수로 정의하고 굴착성능과 형상을 분석하였다. 실험결과, 노즐각과 이격거리가 증가할 때 굴착깊이는 감소하였고 유효 굴착깊이는 증가하는 경향을 보였다. 또한, 실험결과를 바탕으로 노즐 삽입에 필요한 굴착형상 기준을 제안하고 기준에 따른 최적 노즐 운용변수를 도출하였다. 본 연구결과는 향후 암반 천공용 다중 워터젯 노즐 개발 시 유용한 기초연구로 활용될 것으로 기대된다.

• Journal of Biosystems Engineering
• /
• 제33권2호
• /
• pp.115-123
• /
• 2008

This study was conducted to develop an automatic soil water content control system for greenhouse, which consisted of drip irrigation nozzles, soil water content sensors, an on/off valve, a servo-motor assembly and a control program. The control logic adopted in the system was Ziegler-Nichols algorithm and rising time, time constant and over/undershoot ratio as control variables in the system was selected and determined by various control experiments to maintain small delay time and low overshoot. Based on the experimental results, it was concluded that the control system developed in the study could replace the unreliable conventional greenhouse soil water management.

• 한국유체기계학회 논문집
• /
• 제2권3호
• /
• pp.59-66
• /
• 1999

In this study the effects of nozzle diameter on the performance characteristics for the tangential impeller-type water meter are studied experimentally. The nozzle is cut along the tangential direction of the inner case in the water meter. The nozzle shape is round and the number of nozzles used for the experimental study are 8. The performance characteristics are discussed for various nozzle diameters such as 3.1, 3.3, 3.5, 4.0, 4.5 and 5.0 mm. Among the tangential impeller-type water meters, the water meter with the nozzle diameter of 5.0 mm shows the least pressure loss and the instrumental error compared to the Korean Standards.

• 한국유체기계학회 논문집
• /
• 제14권6호
• /
• pp.85-90
• /
• 2011

Recently, many high elevation fountain are constructed for the beauty of beach landscape. Typically, a fountain has several nozzles that shoots water upwards or at an angle into the air. But unfortunately, the weather and wind can cause the water soak nearby walkways and pedestrians. Therefore, in this study, a mathematical model of high elevation fountain is suggested to predict the actual travelling distance of water droplet by the wind. To simplify our treatment of the water flow and to avoid issues such as fluid dynamics and surface tension, we have adopted a particle model for the fountain water. The particles are assumed not to interact with each other, and do not deform during their flight through air.

• 한국압력기기공학회 논문집
• /
• 제8권1호
• /
• pp.8-18
• /
• 2012

In early constructed nuclear power plants, Ni-based Alloys 82/182 had been widely used for dissimilar metal welds (DMW) as a weld filler metal. However, Alloys 82/182 have been proven to be susceptible to primary water stress corrosion cracking (PWSCC) in the nuclear primary water environment. The formation of crack due to PWSCC is also influenced by weld residual stresses. Thus, the accurate estimation of weld residual stresses of DMW is crucial to investigate the possibility of PWSCC and instability behaviors of crack due to PWSCC. In this context, the present paper investigates weld residual stresses of nuclear reactor piping nozzles based on 2-D axi-symmetric finite element analyses based on layer-based approach using maximum molten bead temperature. In particular, the effect of analysis parameters, i.e., a thickness of weld layer, an initial molten bead temperature, convection heat transfer coefficient, and geometric constraints on predicted weld residual stresses was investigated.

• 한국환경과학회지
• /
• 제27권3호
• /
• pp.219-225
• /
• 2018

This study was conducted to investigate the possibility of utilizing various types of nozzles and gas-liquid mixers to increase the dissolution rate of plasma gas containing ozone generated in a dielectric barrier plasma reactor. After selecting the air atomizing nozzle with the highest gas dissolution rate among the 13 types of test equipment, we investigated the influence of the operating factors on the air atomizing nozzle to determine the optimal plasma gas dissolution method. The gas dissolution rate was measured by a simple and indirect method, specifically, the measurement of KLa instead of direct measurement of ozone concentration, which requires a longer analysis time. The results showed that the KLa value of the simple mix of air and water was $0.372min^{-1}$, Which is 1.44 times higher than that ($0.258min^{-1}$) of gas emitted from a normal diffuser. Among the nozzles of the same type, the KLa value was highest for the nozzle having the smallest orifice diameter. Among the 13 types of devices tested, the nozzle with highest KLa value was the M22M nozzle, which is a gas-liquid spray nozzle. The relationship between water circulation flow rate and KLa value in the experimental range was linear. The air supply flow rate and KLa value showed a parabolic-type correlation, while the optimum air supply flow rate for the water circulation flow rate of 1.8 L / min is 1.38 times.

• Journal of Biosystems Engineering
• /
• 제36권1호
• /
• pp.15-22
• /
• 2011

An experimental variable rate nursery sprayer was developed to adjust application rates for canopy volume in real time. The sprayer consisted of two vertical booms integrated with ultrasonic sensors, and variable rate nozzles coupled with pulse width modulation (PMW) based solenoid valves. A custom-designed microcontroller instructed the sensors to detect canopy size and occurrence and then controlled nozzles to achieve variable application rates. A spray delivery system, which consisted of diaphragm pump, pressure regulator and 4-cycle gasoline engine, offered the spray discharge function. Spray delay time, time adjustment in spray trigger for the leading distance of the sensor, was measured with a high-speed camera, and it was from 50 to 140 ms earlier than the desired time (398 ms) at 3.2 km/h under indoor conditions. Consequently, the sprayer triggered 4.5 to 12.5 cm prior to detected targets. Duty cycles of the sprayer were from 20 to 34 ms for senor-to-canopy (STC) distance from 0.30 to 0.76 m. Outdoor test confirmed that the nozzles were triggered from 290 to 380 ms after detecting tree canopy at 3.2 km/h. The spray rate of the new sprayer was 58.4 to 85.2% of the constant application rate (935 L/ha). Spray coverage was collected at four areas of evergreen canopy by water sensitive papers (WSP), and ranged from 1.9 to 41.1% and 1.8 to 34.7% for variable and constant rate applications, respectively. One WSP area had significant (P < 0.05) difference in mean spray coverage between two application conditions.

• 상하수도학회지
• /
• 제8권3호
• /
• pp.26-33
• /
• 1994

To slove the problems by the scum, which causes operational and water quality problems in water treatment plants, several researches were conducted based on the site investigations on twelve large water treatment plants, biological and chemical analysis of scum, analyzing raw water quality data. Two types of scum, which are from scum and floe scum, can be classified based on the analysis and site investigations. The major parameter generating floe scum was indicated as fine bubbles dissolved in the water. The fine bubbles dissolved in the water can be generated by over-saturated air in the water, adding aluminum surface as the coagulant, conducting the break point pre-chlorination and so on. The water spray method, which is one of the physical treatment methods for removing scum, was selected for conducting experiments on the removal efficiency in the flocculation basin of the real water treatment plant. The water spray method was successfully applied for removing scum with the advantages of using spiral nozzles in case of using the raw water rather than the cleaned water.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 후기학술대회논문집
• /
• pp.132-133
• /
• 2005

A study to evaluate the fire extinguishing performance of the water mist system inside simulated machinery spaces according to IMO MSC/Circ.668 was performed. Fire tests were conducted inside a compartment having a area 100$m^2$(10m${\times}$10m) with a ceiling height of 10m and door opening of 2m${\times}$2m in size. Test fuels were used heptane, diesel, wood crib and mineral oil. Water mist nozzles were installed downward at ceiling and horizontally at bilge area. All fires in the test were extinguished within 15minutes of system activation and there was no reignition or fire spread.