• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.4 no.2
• /
• pp.117-131
• /
• 2006

A coupled T-H-M(Thermo-Hydro-Mechanical) analysis was carried out for KENTEX (KAERI Engineering-scale T-H-M Experiment for Engineered Barrier System), which is a facility for validating the coupled T-H-M behavior in the engineered barrier system of the Korean reference HLW(high-level waste) disposal system. The changes of temperature, water saturation, and stress were estimated based on the coupled T-H-M analysis, and the influence of the types of mechanical constitutive material laws was investigated by using elastic model, poroelastic model, and poroelastic-plastic model. The analysis was done using ABAQUS, which is a commercial finite element code for general purposes. From the analysis, it was observed that the temperature in the bentonite increased sharply for a couple of days after heating the heater and then slowly increased to a constant value. The temperatures at all locations were nearly at a steady state after about 37.5 days. In the steady state, the temperature was maintained at $90^{\circ}C$ at the interface between the heater and the bentonite and at about $70^{\circ}C$ at the interface between the bentonite and the confining cylinder. The variation of the water saturation with time in bentonite was almost same independent of the material laws used in the coupled T-H-M processes. By comparing the saturation change of T-H-M and that of H-M(Hydro-Mechanical) processes using elastic and poroelastic material mod31 respectively, it was found that the degree of saturation near the heater from T-H-M calculation was higher than that from the coupled H-M calculation mainly because of the thermal flux, which seemed to speed up the saturation. The stresses in three cases with different material laws were increased with time. By comparing the stress change in H-M calculation using poroelasetic and poroelasetic-plastic model, it was possible to conclude that the influence of saturation on the stress change is higher than the influence of temperature. It is, therefore, recommended to use a material law, which can model the elastic-plastic behavior of buffer, since the coupled T-H-M processes in buffer is affected by the variation of void ratio, thermal expansion, as well as swelling pressure.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.8 no.4
• /
• pp.347-353
• /
• 2010

Source terms of metal waste comprising a spent fuel assembly are relatively important when the spent fuel is pyroprocessed, because cesium, strontium, and transuranics are not a concern any more in the aspect of source term of permanent disposal. In this study, characteristics of radiation source terms for each structural component in spent fuel assembly was analyzed by using ORIGEN-S with a assumption that 10 metric tons of uranium is pyroprocessed. At first, mass and volume for each structural component of the fuel assembly were calculated in detail. Activation cross section library was generated by using KENO-VI/ORIGEN-S module for top-end piece and bottom-end piece, because those are located at outer core with different neutron spectrum compared to that of inner core. As a result, values of radioactivity, decay heat, and hazard index were reveled to be $1.40{\times}10^{15}$ Bequerels, 236 Watts, $4.34{\times}10^9m^3$-water, respectively, at 10 years after discharge. Those values correspond to 0.7 %, 1.1 %, 0.1 %, respectively, compared to that of spent fuel. Inconel 718 grid plate was shown to be the most important component in the all aspects of radioactivity, decay heat, and hazard index although the mass occupies only 1 % of the total. It was also shown that if the Inconel 718 grid plate is managed separately, the radioactivity and hazard index of metal waste could be decreased to 20~45 % and 30~45 %, respectively. As a whole, decay heat of metal waste was shown to be negligible in the aspect of disposal system design, while the radioactivity and hazard index are important.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.6 no.3
• /
• pp.189-203
• /
• 2008

The physical and chemical properties of radioactive waste drums, which have been temporarily stored on site, should be characterized before their shipment to a disposal facility in order to prove that the properties meet the acceptance guideline. The investigation of NDT(Nondestructive Test) method was figured out that the contents in drum, the quantitative analysis of free standing water and void fraction can be examined with X-ray NDT techniques. This paper describes the characteristics of X-ray NDT such as its principles, the considerations for selection of X-ray system, etc. And then, the waste drum characteristics such as drum type and dimension, contents in drum, etc. were examined, which are necessary to estimate the optimal X-ray energy for NDT of a drum. The estimation results were that: $(R)\acute{A}$ the proper X-ray energy is under 3 MeV to test the drums of 320 ${\beta}\S$ and less; $(R)\ddot{E}$ both X-ray systems of 450 keV and/or 3 MeV might be needed considering the economical efficiency and the realization. The number of drums that can be tested with 450 keV and 3 MeV X-ray system was figured out as 42,327 and 18,105 drums (based on storage of 2006. 12), respectively. Four testing scenarios were derived considering equipment procurement method, outsourcing or not, etc. The economical and feasibility assessment for the scenarios was resulted in that an optimal scenario is dependent on the acceptance guide line, the waste generator's policy on the waste treatment and the delivery to a disposal facility, etc. For example, it might be desirable that a waste generator purchases two 450 keV mobile system to examine the drums containing low density waste, and that outsourcing examination for the high density drums, if all NDT items such as quantitative analysis for 'free standing water' and 'void fraction', and confirmation of contents in drum have to be characterized. However, one 450 keV mobile system seems to be required to test only the contents in 13,000 drums per year.

• Korean Journal of Veterinary Service
• /
• v.29 no.3
• /
• pp.347-364
• /
• 2006

This study is concerned with assessment of diethylnitrosamine (DEN 0.01 %) induced liver cell carcinogenesis by measurement of changes preceding the development of neoplasms. Therefore, it was undertaken to investigate changes of liver-specific enzyme activities in Sprague-Dawley (SD) rats by ad libitum feeding of DEN. And also. the changes of hepatic morphology in SD rats were detected by haematoxylineosin stain and immunohistochemistry (PCNA). 5- Fluorouracil (5- FU) is one of the most widely used anticancer agents for digestive cancers including hepatocellular carcinoma, and is known to affect the cell cycle and induce apoptosis of cancer cells. In the present study, SD rats were given drinking water containing 0.01% diethylnitrosamine (DEN) for 8 weeks. Minor behavioral change, brittleness of hair and decreased amount of water and diet intake were observed in rats 4 weeks after DEN administration. The body and liver weights were significantly (p < 0.05) decreased in rats 11 weeks after DEN administration. The liver weight ratio to body weight was rather stable and not significantly decreased in the all treatment groups. The liver specific enzyme activities (AST, ALT, ${\gamma}$-GTP) were significantly increased in all treatment groups compared to control group (p < 0.05). Variable size of liver tumor and hepatomegaly were observed in rats treated with DEN after 10 weeks. Numerous vacuoles were seen on the midzonal and or peripheral areas of hepatic lobules. The large and polymorphological hepatocytes with eosinophilic cytoplasm or densely basophilic mitotic nucleoli were seen. Several proliferative small round cells were seen on vacuolated and necrotic areas in peripheral hepatic lobules or portal areas. PCNA-positive cells were seen on the vacuolated portal areas and peripheral areas of hepatic lobules in the areas of small round cells. We examined functional and morphological changes of livers by 5 - FU treatments on DEN -treated rat. The DEN -treated rats compared to 5 - FU -treated rats after DEN treatment for 8 weeks. The serum total protein and triglyceride were significantly (p < 0.05) decreased, and the liver enzyme activities of AST and ALT were significantly(p < 0.05) increased. After 8 weeks, in the non-5-FU -treated group, the size of liver tumor were varied and hepatomegaly were observed, hepatocellular vacuolization, necrosis and steatosis were observed on the midzonal and peripheral areas of hepatic lobules. The large and polymorphological hepatocytes were seen, the interlobular connective tissues were proliferated. PCNA positive cells were seen in the portal areas and peripheral areas of hepatic lobules in the non-5-FU-treated group. In hepatocytes, condensation of nuclear chromatin and vacuolization were observed, shape of the nuclei were irregular, the degraded nuclei and organelles were observed. The livers of rats in the 5 - FU treatment group were seen grossly brilliant, red-brown color, and the vacuolated and degenerated regions, hyperplastic nodules were not nearly observed. In the electron microscope, the cytoplasm of the hepatocytes contained a large number of mitochondria, rough endoplasmic reticulum, developed organelles surrounding nuclei. The above findings suggest that 5 - FU will be effective as anti -liver tumor drug.

• Journal of the Korean earth science society
• /
• v.21 no.2
• /
• pp.103-115
• /
• 2000

The ability-grouping is the essence of the seventh educational curriculum, applied to school from year 2000, and its enriched-supplementary type will be carried out for science course. This study examines the effect of the enriched-supplementary ability-grouping within class to student's academic achievement and the attitude, related to science. Thus we developed teaching and learning methods with intellectual level about the subject of 'Water Circulation and Weather Change' in Middle-School Science 2. Then we tested 152 eighth graders who were divided into the experimental and control groups. The experimental one was taught through the ability-grouping for about six weeks, while the control through conventional lecture. The improvement of the experimental group in academic achievement was more effective than that of the control, and particularly to below-average students who ranked in lower thirty percent. The experimental one got more negative change in domain 'Science as a Subject, and in subdomain 'Anxiety in Science Lesson'. While outstanding students who ranked in upper thirty percent showed a significant positive change in subdomain 'Satisfaction in Teaching Method, the below-average were negatively changed in subdomain 'Anxiety in Science Lesson'. The current ability-grouping was suitable for the improvement of academic achievement, but not for the general attitude related to science. In order to enhance the ability-grouping effect in science education, we need to additionally consider student's interest and concern in grouping, and develop various teaching and learning methods together with proper textbook contents.

• Korean Journal of Poultry Science
• /
• v.41 no.4
• /
• pp.297-303
• /
• 2014

Heat manipulation at early age has been known to help chickens cope with heat stress later in life. The present study was conducted to determine the effects of early heat conditioning at 5 days of age on performance in broilers when re-exposed to heat stress later in life. Day-old, 256 Arbor Acre boiler chicks were housed in two identical rooms where all broilers were exposed to a 23-h light: 1-h dark cycle throughout the study and provided with feed and water ad libitum. At the age of 5 days, one group was exposed to $37^{\circ}C$ for 24 hours and then returned to the temperature at which control birds were maintained (early heat condition group) while the other was maintained without heat modulation (Control). On 21 days, broilers were regrouped into 4 groups (CON+CON: control+control; CON+HS: control+heat stress; HC+CON: heat conditioning+control; HC+HS: heat conditioning+heat stress), and given 7 days for adaptation. On 28 days, birds in one room were exposed to heat stress ($21^{\circ}C{\rightarrow}31^{\circ}C$) for 3 days whereas those in the other were at room temperature. Heat stress resulted in decreased feed intake, water intake, and body weight gain (P<0.05), but increased rectal temperature and mortality (P<0.05). No beneficial effects of heat conditioning were detected when broilers were exposed to heat stress again at later in life. The present results were discussed together with other studies regarding possible differences in methods such as ages of breeders and strains, which may have resulted in the failure of heat conditioning to help broilers resist heat stress.

• Journal of Aquaculture
• /
• v.4 no.1
• /
• pp.31-66
• /
• 1991

This paper deals with the reproductive ecology e.g., number of the pre-spawning moults, morphological characteristics of the pre-spawning moult the common moult, daily ration druing a molting cycle mating behavior, structures of spermatozoa and spermatophore, structure of vas deferens, mechanisms of the oviposition and brooding into the egg-chambers, a suitable time for the artificial mating and fertilization, time sequence of the oviposition and brooding into egg-chambers from the copulation, responses to temperature and chlorinity on the egg development and hatching, effect of temperatures on duration of egg development, physical mechanism of the egg hatching, to make an attempt for the artificial spawning and brooding to establish a suitable system of the artificial seedling-production for the aquaculture. 1. Females molted commonly $8{\~}10$ times at an interval of $17{\~}18$ days at $28^{\circ}C,\;3.26\~4.35\%_{\circ}$ while the prespawning moltings were $4{\~}5$ times at an interval of $13{\~}14$ days. The suitable state for artificial copulation was within 14 hours elapsed from the prespawning moltings (most suitable state was within 8 hours). Males discharged a gelatinous spermatophore and placed it on the females sternum during copulation. Oviposition was seen $6{\~}17$ hours after copulation. External fertilization was considered to take place at oviposition. Fertilized eggs held in egg-chambers forming between pleopods were about $5000{\~}6000$ in females those sizes about 6.5 cm in body length. 2. Eggs immediately after oviposition were elliptic shape, measuring $0.58{\times}0.48$ mm up to hatching. Their sizes increased with egg development and finally reached $0.85{\times}0.54$ mm up to hatching. The relationship between the long axis of the egg(Y in U) and days elapsed(X) was expressed as Y= 5.60194 + 0.007358X. The eggs performed superficial cleavage and their cleavage furrows became visible at the 4-daughter-nucleus stage. The eggs showed normal development up to hatching at water temperature range of $22{\~}30^{\circ}C$ (optimum temperature : $26{\~}28^{\circ}C$) and at chlorinity range of $0.00\~6.64\%_{\circ}$ (optimun chlorinity : $2.21{\%}_{\circ}$). The relationship between incubation period (Y in days) and water temperature(X in $^{\circ}C$) could be expressed as Y= 50.803-1.3555X. The eggs hatched $12{\~}13$ days after oviposition at $28.0{\~}28.6^{\circ}C$ 3. The pre-spawning moltings were appreciably different in the morphologic structure from those of common moltings. Breeding setae and dresses were formed on the thoracic regions, abdominal epimerae and the bases of the first to fourth pleopods in order to prepare and support oviposition, transfering and supporting eggs in egg-chambers up to hatching. These supplementary breeding organs were observed only at reproductive seasons.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.29 no.4
• /
• pp.527-536
• /
• 1996

The patterns of diel horizontal migration (DHM) of 7 copepod species are compared as part of a general investigation of the zooplankton adaptations to the surf zone habitats. In a sandy shore surf zone of Yongil Bay, 3 sites such as the bottom and surface of 1 m water depth and water's edge are sampled with a sledge net(n=108). The surf zone copepod assemblage is dominated by 7 species; Acartia hudsonica, Fseudodiaptomus marinus, Paracalanus indicus, Calanus sinicus, Oithona similis, Sinocalanus tenellus and Labidocera bipinnata. Threefold variations in copepod abundance are observed within a diel cycle. Abundances of 7 dominant species and total copepods captured in the surface exhibit significant diel differences, but those taken in the bottom are not significantly affected by diel period. It is shown that about $90\%$ of the surf zone copepods performed DHM. The nocturnal high densities of copepods occurred for a neap tide when the offshore winds prevailed, suggesting the animals' ability for horizontal orientation and an active locomotion without invoking passive transportation by currents. Photoreactive behavior of copepods triggered by relative changes in light intensity may be a primary factor inducing DHM by aggregating in the surf zone during the night and spreading out at day; then copepods may reduce encounters with visual predators. In A. hudsonica, ontogenetic variations in timings of DHM are evident. Such variations are likely to minimize intraspecific competition for diets. Data on shoreward migration of copepods indicate that A. hudsonica, P. indicus, O. similis and S. tenellus can maintain swimming velocities of about $20m\;h^{-1}$ for durations of more than an hour. Our observations of strong diel difference in abundances point out the need for both day and night samplings in surf zone habitats, if the importance of these habitats to planktonic copepods are to be fully understood.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.26 no.4
• /
• pp.677-687
• /
• 1999

This study was performed to evaluate the effect of aging and thermal cycling on the tensile strength of six commercially available glass-ionomer materials: two chemically set glass-ionomer materials(Fuji II, Fuji IX), two resin-modified glass-ionomer materials(Fuji II LC, Vitremer), and two polyacid-modified composite resins(Compoglass, Dyract). Rectangular tension test specimens were fabricated in a teflon mold giving 5mm in gauge length and 2mm in thickness. All samples were divided into 3 groups. Group 1 was immersed in a $37^{\circ}C$ distilled water for 1 hour. Group 2 was immersed in a $37^{\circ}C$ distilled water for 30 days. Group 3 was subjected to 10,000 thermal cycles between $5^{\circ}C$ and $55^{\circ}C$, and the immersion time in each bath was 15 seconds per cycle. Tensile testing was carried out at a cross-head speed of 0.5mm/min and fracture surfaces were examined with scanning electron microscope. The results obtained were summarized as follows; 1. The polyacid-modified composite resins were stronger than the resin-modified glass-ionomer materials, which were much stronger than the conventional glass-ionomer materials. 2. Tensile strengths were slightly increased after aging treatments for 30days. 3. Tensile strengths of conventional glass ionomers were significantly increased after thermal cycling treatment(p<0.01). 4. The highest tensile strength value of 45.4MPa was observed in the Dyract group and the lowest value of 13.3MPa was observed in the Fuji II LC group after the thermal cycling test, and the strengths of polyacid-modified composite groups were significantly higher than those of other groups. 5. The highest characteristic strength value of 48.6MPa was obtained in the Dyract group, however the highest Weibull modulus value of 8.9MPa was obtained in the Compoglass group after thermal cycling test.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.21 no.12
• /
• pp.715-732
• /
• 2009

This article reviews the papers published in the Korean Journal of Air-Conditioning and Refrigeration Engineering during 2008. It is intended to understand the status of current research in the areas of heating, cooling, ventilation, sanitation, and indoor environments of buildings and plant facilities. Conclusions are as follows. (1) Research trends in thermal and fluid engineering have been surveyed in the categories of general fluid flow, fluid machinery and piping, new and renewable energy, and fire. Well-developed CFD technologies were widely applied in developing facilities and their systems. New research topics include fire, fuel cell, and solar energy. Research was mainly focused on flow distribution and optimization in the fields of fluid machinery and piping. Topics related to the development of fans and compressors had been popular, but were no longer investigated widely. Research papers on micro heat exchangers using nanofluids and micro pumps were also not presented during this period. There were some studies on thermal reliability and performance in the fields of new and renewable energy. Numerical simulations of smoke ventilation and the spread of fire were the main topics in the field of fire. (2) Research works on heat transfer presented in 2008 have been reviewed in the categories of heat transfer characteristics, industrial heat exchangers, and ground heat exchangers. Research on heat transfer characteristics included thermal transport in cryogenic vessels, dish solar collectors, radiative thermal reflectors, variable conductance heat pipes, and flow condensation and evaporation of refrigerants. In the area of industrial heat exchangers, examined are research on micro-channel plate heat exchangers, liquid cooled cold plates, fin-tube heat exchangers, and frost behavior of heat exchanger fins. Measurements on ground thermal conductivity and on the thermal diffusion characteristics of ground heat exchangers were reported. (3) In the field of refrigeration, many studies were presented on simultaneous heating and cooling heat pump systems. Switching between various operation modes and optimizing the refrigerant charge were considered in this research. Studies of heat pump systems using unutilized energy sources such as sewage water and river water were reported. Evaporative cooling was studied both theoretically and experimentally as a potential alternative to the conventional methods. (4) Research papers on building facilities have been reviewed and divided into studies on heat and cold sources, air conditioning and air cleaning, ventilation, automatic control of heat sources with piping systems, and sound reduction in hydraulic turbine dynamo rooms. In particular, considered were efficient and effective uses of energy resulting in reduced environmental pollution and operating costs. (5) In the field of building environments, many studies focused on health and comfort. Ventilation. system performance was considered to be important in improving indoor air conditions. Due to high oil prices, various tests were planned to examine building energy consumption and to cut life cycle costs.