• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.4
• /
• pp.94-103
• /
• 2023

Built in urban ares tunnels is necessary to accurately grasp not only the above-ground environment of the tunnel but also the below-ground environment of the tunnel for design and construct. However, fully coupled analysis of stress and flow is very difficult due to the limited function of the tunnel numerical analysis program and difficulty in using program. This can lead to excessive design that increases the construction cost or occur problems that can lead to accidents during construction. In particular, in the case of an urban tunnel has a low layer soil section above the tunnel and the groundwater level exists in the upper layer of the tunnel. Therefore, a reduction in the groundwater level during underground construction may increase the effective stress of the upper layer and cause the ground to subsidence. So It is necessary to design after accurately evaluating the change in the groundwater level. In this study, the tunnel's behavioral characteristics were analyzed through fully coupled analysis of stress and flow according to the drainage type for an urban underground tunnel.

• Applied Chemistry for Engineering
• /
• v.34 no.3
• /
• pp.307-312
• /
• 2023

In this study, a catalytic oxidation-heat recovery system was designed that can remove unreacted with a concentration of about 1% to 6% in the exhaust gas of hydrogen fuel cells and recover heat to ensure safety in the hydrogen economy. The safety system was devised by filling hydrogen oxidation catalysts at room temperature that can remove unreacted hydrogen without any energy source, and an exhaust-heat recovery device was integrated to efficiently recover the heat released from the oxidation reaction. Through CFD analysis, variations in pressure and fluid within the system were shown depending on the filling conditions of the hydrogen oxidation system. In addition, it was found that waste heat could be recovered by optimizing the temperature of the exhaust gas, flow rate, and pressure conditions within the heat recovery system and securing hot water above 40 ℃ by utilizing the exhaust gas oxidation heat source above 300 ℃. Through this study, it was possible to confirm the potential of utilizing hydrogen processes, which are applied in small to medium-sized systems such as hydrogen fuel cells, as a safety system by evaluating them at a pilot scale. Additionally, it could be a safety guideline for responding to unexpected hydrogen safety accidents through further pilot-scale studies.

• Journal of the Korean Wood Science and Technology
• /
• v.10 no.1
• /
• pp.5-37
• /
• 1982

Plywood used for construction as a decorative inner material is inflammable to bring large fire accidents and burn out human life and their properties. To diminish the fire disaster, fire retardant plywood has been required indeed. In the methods of manufacturing the fire retardant plywood the soaking method is occasionally used. However after soaking plywood into fire retardant chemical solutions, redrying of soaked plywood is the most important. In this study, 3.5mm thin and 5.0mm thick plywoods were selected for fire retardant treatment. Treating solutions were prepared for 20% dilute solutions of ammonium sulfate, monoammonium phosphate, diammonium phosphate, borax-boric acid and minalith, and water solution. 1-, 3-, 6-, and 9 hour-soaking treatments were applied and after treatments hot plate drying was applied to those treated plywoods at $90^{\circ}C$, $120^{\circ}C$ and $150^{\circ}C$, of press temperature. Drying rates, drying curves, water absorption rates of fire retardant chemicals, weight per volume and fire retardant degree of plywood were investigated. The results may be summarized as follows: 1. The plywoods treated with ammonium sulfate, monoammonium phosphate and diammonium phosphate and diammonium phosphate showed increase of chemical absorption rate with proportion to increase of treating time, but not in case of the plywood treated with borax-boric acid and minalith. 2. In the treatment of definite time, the absorption rate per unit of volume of plywood showed higher in thin plywood (thickness of 3.5mm) than in thick plywood (thickness of 5.0mm). In both thin and thick plywoods, the highest absorption rate was observed in 9 hour-treatment of ammonium sulfate. The value was 1.353kg/$(30cm)^3$ in thin plywood and 1.356kg/$(30cm)^3$ in thick plywood. 3. The volume per weight of plywood after chemical treatment increased remarkably and. after hot plate drying, the values were to a little extent higher than before chemical treatment. 4. The swelling rates of thickness in chemical-treated plywoods increased similarly with that of water-treated plywood in 1- and 3 hour-treatment of both thin and thick plywoods. But in 6- and 9 hour-treatment, the greater increased value showed in water-treated ply wood than any other chemical, especially in thick plywood. 5. The shrinkage rates after hot plate drying showed the same tendency as the swelling rate, and the rate showed the increasing tendency with proportion to increase of treating time in thick plywood of both chemical and water treatments. 6. Among drying curves, the curves of water-treated plywood placed more highly than chemical-treated plywood without-relation to thickness in 6- and 9 hour-treatment except in 1- and 3 hour-treatment. 7. The drying rate related to thickness of treated plywood, was twice above in thin plywood compared with thick plywood. 8. The drying rate remarkably increased with proportion to increase of the plate temperature and, the values were respectively 1.226%/min., 6.540%/min., 25.752%/min. in hot plate temperature of $90^{\circ}C$, $120^{\circ}C$, $150^{\circ}C$ in thin plywood and 0.550%/min., 2.490%/min, 8.187%/min, in hot plate temperature of $90^{\circ}C$, $120^{\circ}C$, $150^{\circ}C$ in thick plywood. 9. In the treatment at $120^{\circ}C$ of hot plate temperature, the drying rates of chemical-treated plywood showed the highest value in monoammonium phosphate of thin plywood and in diammonium phosphate of thick plywood. But the drying rate of water-treated plywood was highest in 6- and 9 hour-treatment. 10. The fire retardant degree of chemical-treated plywood was higher than that of the untreated plywood as shown in loss of weight, burning time, flame-exhausted time and carbonized area. 11. The fire-retardant effect among fire retardant chemicals were the greatest in diammonium phosphate, the next were in monoammonium phosphate and ammonium sulfate, and the weakest were in borax-boric and minalith.

• The Korean Journal of Air & Space Law and Policy
• /
• v.31 no.2
• /
• pp.3-35
• /
• 2016

The United States Constitution gives power to the federal district courts to hear admiralty cases. 28 U.S.C. §.133, which states that "The district courts shall have original jurisdiction, exclusive of the Courts of the States, of any civil case of admiralty or maritime jurisdiction." However, the determination of whether a case is about admiralty or maritime so that triggers admiralty jurisdiction was not a simple question. Through numerous legal precedents, the courts have drawn a line to clarify the boundary of admiralty cases. This unique jurisdiction is not determined by the mere involvement of a vessel in the case or even by the occurrence of an event on a waterway. As a general rule, a case is within admiralty jurisdiction if it arises from an accident on the navigable waters of the United States (locus test) and involves some aspect of maritime commerce (nexus test). With regarding to the maritime nexus requirement, the US Supreme Court case, Executive Jet Aviation, Inc. v. City of Cleveland, held that federal courts lacked admiralty jurisdiction over an aviation tort claim where a plane during a flight wholly within the US crashed in Lake Erie. Although maritime locus was present, the Court excluded admiralty jurisdiction because the incident was "only fortuitously and incidentally connected to navigable waters" and bore "no relationship to traditional maritime activity." However, this historical case left a milestone question: whether an aircraft disaster occurred on navigable water triggers the admiralty jurisdiction, only for the reason that it was for international transportation? This article is to explore the meaning of admiralty jurisdiction over aviation accidents at US courts. Given that the aircraft engaged in transportation of passenger and goods as the vessels did in the past, the aviation has been linked closely with the traditional maritime activities. From this view, this article reviews a decision delivered by the Seventh Circuit regarding the aviation accident occurred on July 6, 2013 at San Francisco International Airport.

• Economic and Environmental Geology
• /
• v.50 no.5
• /
• pp.341-352
• /
• 2017

Along with Cs-137 (half-life: 30.17 years), Sr-90 (half-life: 28.8 years) is one of the most important environmental monitoring radioactive elements. Rapid and easy monitoring method for Sr-90 using Laser-Induced Breakdown Spectroscopy (LIBS) has been studied. Strontium belongs to a bivalent alkaline earth metal such as calcium and has similar electron arrangement and size. Due to these similar chemical properties, it can easily enter into the human body through the food chain via water, soil, and crops when leaked into the environment. In addition, it is immersed into the bone at the case of human influx and causes the toxicity for a long time (biological half-life: about 50 years). It is a very reductive and related with the specific reaction that makes wet analysis difficult. In particular, radioactive strontium should be monitored by nuclear power plants but it is very difficult to be analysed from high-cost problems as well as low accuracy of analysis due to complicated analysis procedures, expensive analysis equipment, and a pretreatment process of using massive chemicals. Therefore, we introduce the Laser-Induced Breakdown Spectroscopy (LIBS) analysis method that analyzes the elements in the sample using the inherent spectrum by generating plasma on the sample using pulse energy, and it can be analyzed in a few seconds without preprocessing. A variety of analytical plates for samples were developed to improve the analytical sensitivity by optimizing the laser, wavelength, and time resolution. This can be effectively applied to real-time monitoring of radioactive wastewater discharged from a nuclear power plant, and furthermore, it can be applied as an emergency monitoring means such as possible future accidents at a nuclear power plants.

• Journal of Korean Society of Forest Science
• /
• v.56 no.1
• /
• pp.1-25
• /
• 1982

Plywood used for construction as a decorative inner material is inflammable and can cause fire accidents. causing destruction of human life and property. To diminish the fire disaster, fire retardant plywood is indeed required. In the methods of manufacturing the fire retardant plywood, a soaking method is occasionally used. However after soaking plywood into fire retardant chemical solutions redrying of soaked plywood is of the utmost importance. In this study 3.5mm and 5.0mm thickness plywoods were selected for fire retardant treatment. Treating solutions were prepared for 20% dilute solutions of ammonium sulfate, monoammonium phosphate, diammonium phosphate, borax-boric acid minalith, and water solution, 1-, 3-, 6-, and 9 hour-soaking treatments in borax-boric acid and minalith, and 6- and 9 hours in the other chemicals were applied and after the treatment hot drying was applied to treated plywoods at $90^{\circ}C$, $120^{\circ}C$ and $150^{\circ}C$ of press temperature. Drying rates, drying curves, water absorption rates of fire retardant chemicals, weight per volume and fire retardant degree of plywood were investigated. The results may be summarized as follows: 1) In the 9 hours-soaking treatment of fire retardants by hot and cold bath method, the chemical retentions of 3.5mm thickness plywood could be attained within the range ($1.125-2.25kg/(30cm)^3$) of minimum retention specification as follows: $1.353kg/(30cm)^3$ in monoammonium phosphate, $1.331kg/(30cm)^3$ in diammonium phosphate, $1.263kg/(30cm)^3$ in ammonium sulfate, $1.226kg/(30cm)^3$ in borax-boric acid. But the chemical retention, $0.906kg/(30cm)^3$, in minalith could not be attained within the range of minimum retention specification. And also in case of 5.0mm thickness plywood, chemical retentions, as $1.356kg/(30cm)^3$ and $1.166kg/(30cm)^3$ respectively, of ammonium sulfate and diammonium phosphate could be attained within the range minimum retention specification, but the other fire retardant chemicals could not. 2) In the 6- and - hours-soaking treatments of 3.5mm and 5.0mm thickness plywood, the drying curve sloped of chemical treated plywood was smaller than that of water treated. The drying rate related to thickness of treated plywood, was about three times as fast in 3.5mm thickness plywood compared with 5.0mm thickness plywood. 3) In the treatment at $120^{\circ}C$ of hot platen temperature, the drying rates of chemical-treated plywood showed the highest quantity in diammonium phosphate of 3.5mm and 5.0mm thickness plywood. But the drying rate of water treated plywood was highest during the 6- and 9 hours-soaking treatments. 4) The drying rate remarkably increased with proportion to increase of the platen temperature, and the values were respectively 1.23%/min., 6.54%/min., 25.75%/min. in hot platen temperature of $90^{\circ}C$, $120^{\circ}C$, $150^{\circ}C$ in 3.5mm thickness plywood and 0.55%.min., 2.49%/min., 8.19%/min. in hot platen temperature of $90^{\circ}C$, $120^{\circ}C$, $150^{\circ}C$ in 5.0mm thickness plywood. 5) In the fire retardant degree of chemical treated plywood, the loss in weight was the smallest in diammonium phosphate, next was in monoammonium phosphate and ammonium sulfate, and the greatest was in borax-boric acid and minalith. And the fire-retardant effect in burning time, flame-exhausted time and carbonized area were greatest in diammouniun phosphate, next were in monoammonium phosphate and ammonium sulfate, and the weakest were in borax-boric acid and minalith.

• Journal of Environmental Impact Assessment
• /
• v.4 no.3
• /
• pp.41-48
• /
• 1995

In former times the protection of our environment didn't play an important role due to the fact that emissions and effluents were not considered as serious impacts. However, opinions and scientific measurements meanwhile confirmed that the impacts are more serious than expected. Thus measures to protect our earth has to be taken into consideration. A part of these measures in the Environmental Impact Assessment (EIA). One of the most important parts of the EIA is the collection of basic datas and the following evaluation. Experience out of the daily business of Gerling Consulting Group shows that the content of the EIA has to be revised and enlarged in certain fields. The historical development demonstrated that in areas in which the population and the industrial activities reached high concentration there is a high necessity to develop strict environmental laws and regulations. Maximum values of the concentration of hazardous materials were fixed concerning the emission into and water. Companies not following these regulations were punished. The total amount of environmental offences increased rapidly during the last decade, at least in Germany. During this development the public consciousness concerning environmental affairs increased as well in the industrialized countries. But it could clearly be seen that the development in the field of environmental protection went into the wrong direction. The technologies to protect the environment became more and more sophisticated and terms as: "state of the art" guided more and more to lower emissions, Filtertechnologies and wastewater treatment for example reached a high technical level-but all these sophisticated technologies has one and the same characteristic: they were end-of-the pipe solutions. A second effect was that this kind of environmental protection costs a lot of money. High investments are necessary to reduce the dust emission by another ppm! Could this be the correct way? In Germany the discussion started that the environmental laws reduce the attractivity to invest or to enlarge existing investments within the country. Other countries seem to be not so strict with controlling the environmental laws which means it's simply cheaper to produce in Portugal or Greece. Everybody however knows that this is not the correct way and does not solve the environmental problems. Meanwhile the general picture changes a little bit and we think it changes into the correct direction "End-of-the-pipe" solutions are still necessary but this word received a real negative touch and nobody wants to be brought into connection with this word received a real negative touch and nobody wants to be brought into connection with this word especially in connection with environmental management and safety. Modern actual environmental management starts in a different way. Thoughts about emissions start in the very beginning of the production, they start with the design of the product and modification of traditional modes of production. Basis of these ideas are detailed analyses of products and processes. Due to the above mentioned facts that the public environmental consciousness changed dramatically a continous environmental improvement of each single production plant has to be guarantied. This question is already an important question of the EIA. But it was never really checked in a wholistic approach. Environmental risks have to be taken into considerations during the execution of an EIA. This means that the environmental risks have to be reduced down to a capable risk-level. Environmental risks have to be considered within the phase of planning, during the operation of a plant and after shut down. The experience shows that most of the environmental relevant accidents were and caused by human fault. Even in highly protected plants the human risk-factor can not be excluded during evaluation of the risk-potential. Thus the approach of an EIA has to regard technical evaluations as well as organizational thoughts and the human factor. An environmental risk is a threat to the environment. An analysis of the risk concerning the organizational and human aspect however never was properly executed during an EIA. A possible solution could be to use an instrument as the actual EMAS (Environmental Management System) of the EC for more accurate evaluation of the impact to the environment during an EIA. Organizations or investors could demonstrate by an approved EMAS or even by showing their installment of EMAS that not only the technical level of the planned investment meets the requested standards but as well the actual or planned management is able to reduce the environmental impact down to a bearable level.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.5
• /
• pp.628-636
• /
• 2018

Because large buoys are mainly made of steel, they are heavy and vulnerable to corrosion by sea water. This makes buoy installation and maintenance difficult. Moreover, vessel collision accidents with buoys and damage to vessels due to the material of buoys (e.g., steel) are reported every year. Recently, light buoys adopting eco-friendly and lightweight materials have come into the spotlight in order to solve the previously-mentioned problems. In Korea, a new lightweight buoy with a 7-Nautical Mile lantern adopting expanded polypropylene (EPP) and aluminum to create a buoyant body and tower structure, respectively, was developed in 2017. When these light buoys are operated in the ocean, the visibility and angle of light from the lantern installed on the light buoys changes, which may cause them to function improperly. Therefore, research on the performance of light buoys is needed since the weight distribution and motion characteristics of these new buoys differ from conventional models. In this study, stability estimation and motion analyses for newly-developed buoys under various environmental conditions considering a mooring line were carried out using ANSYS AQWA. Numerical simulations for the estimation of wind and current loads were performed using commercial CFD software, Siemens STAR-CCM+, to increase the accuracy of motion analysis. By comparing the estimated maximum significant motions of the light buoys, it was found that waves and currents were more influential in the motion of the buoys. And, the estimated motions of the buoys became larger as the sea state became worser, which might be the reason that the peak frequencies of the wave spectra got closer to those of the buoys.

• The Korean Journal of Air & Space Law and Policy
• /
• v.34 no.1
• /
• pp.235-268
• /
• 2019

Under the Aviation Safety Act of Korea, any person who intends to operate a drone is required to follow the operational conditions listed below, unless approved by the Minister of Land, Infrastructure, Transport and Tourism; (i) Operation of drones in the daytime, (ii) Operation of drones within Visual Line of Sight, (iii) Maintenance of a certain operating distance between drones and persons or properties on the ground/ water surface, (iv) Do not operate drones over event sites where many people gather, (v) Do not transport hazardous materials such as explosives by drone, (vi) Do not drop any objects from drones. Requirements stated in "Airspace in which Flights are Prohibited" and "Operational Limitations" are not applied to flights for search and rescue operations by public organizations in case of accidents and disasters. This paper analyzes legal issues as to definition and regulations of drones in Korean Aviation Safety Act. This paper, also, offers some implications and suggestions for regulations of drones under Korean Aviation Safety Act by comparing the regulations of drones in Japanese Civil Aeronautics Act.