• Journal of Animal Science and Technology
• /
• v.47 no.4
• /
• pp.513-524
• /
• 2005

This study was conducted to introduce recycling procedures of food waste(FW) as feed according to the dehydration, semi-dehydration fermentation and liquid fermentation methods through the on-site survey of companies related, to trace physico-chemical components and nutritional losses depending upon the processing stage for each method and finally to suggest more desirable methodology for the efficient utilization of FW as animal feed. For the dehydration method, dewatering of FW alone reduced(P<0.05) moisture(approximately 10%) and ether extract contents and increased(P<0.05) fiber contents. Dewatering and subsequent dehydration of FW decreased(P<0.05) contents of ether extract, limiting amino acids such as lysine, methionine and histidine, pepsin digestibility of protein by half, and NaCl content by 40%, increased(P<0.05) contents of fiber, crude ash, Ca and P, and did not alter(P>0.05) pH. The semi-dehydration fermentation method of FW did not affect(P>0.05) the chemical components, pepsin digestibility of protein, pH and NaCl content. For the liquid fermentation method, pasteurization and fermentation of FW decreased(P<0.05) contents of dry matter, ether extract, crude fiber, lysine and NaCl; however, it did not affect(P>0.05) other chemical components, pepsin digestibility of protein and pH. Among the processing methods, nutrient losses were highest for the dehydration method(25% of metabolizable energy loss, 12% of organic matter loss) and little for the semi-dehydration and liquid fermentation methods. The on-site survey of companies related revealed that the existence of foreign materials in FW products were problematic for all the three companies surveyed, thus it was necessary to develop a more efficient screener. Before feeding FW-containing diets to pigs, high quality of protein and energy feedstuffs needed to be fortified for the dehydration method. For the semi-dehydration fermentation method, the scientific diet formulation technology was required at the initial mixing stage. For the liquid fermentation method, possibly most energetic and proteinaceous feeds needed to be supplemented for the normal animal growth.

• Clean Technology
• /
• v.22 no.4
• /
• pp.274-280
• /
• 2016

In this study, it was to develop a chemical method that can recycle the cutting oil which accounts for about 25% of the cost of the process among containing materials of silicon waste sludge generated in the process for producing a solar cell wafer. The 7 types of reagents have been used, including acetone, HCl, NaOH, KOH, $Na_2CO_3$, HF, $CH_2Cl_2$, etc. for this experiment. And It was carried out at a speed of 3000 rpm for 60 minutes centrifugation after performing a reaction with a waste sludge at various concentrations. As a result, the best reagents and conditions for separating the solid such as a silicon powder and a metal powder and liquid cutting oil were identified as 0.3 N NaOH. It is found to be pH 6.05 in a post-processing recycled cutting oil with 0.3 N NaOH after reaction of waste sludge and 0.1 N HCl which is effective to remove metal powder in order to adjust the pH to suit the properties of the weak acid is a commercially available cutting oil and it showed excellent turbidity than when applied to sludge with 0.3 N NaOH alone. The results of FT-IR analysis which can compare the properties of the commercially available cutting oil shows it has a possibility of recycling oil. The cutting oil recovery rate obtained through the experiment was found to be 86.9%.

• Nuclear Engineering and Technology
• /
• v.8 no.4
• /
• pp.231-242
• /
• 1976

The effects of temperature and pressure of leaching water on the leaching of radionuclides from bitumen-waste products were studied. The principal results are as follows: The fraction of $^{90}$ Sr and $^{137}$ Cs leached for periods of up to 120 days at 8atm was 2.1$\times$10$^{-6}$ ($\textrm{cm}^2$/g)$^{-1}$ , day$^{-1}$ and 6.02$\times$10$^{-5}$ ($\textrm{cm}^2$/g)$^{-1}$ day$^{-1}$ respectively and at 5$^{\circ}C$, 1.7$\times$10$^{-5}$ ($\textrm{cm}^2$/g)$^{-1}$ day$^{-1}$ and 4.01$\times$10$^{-5}$ ($\textrm{cm}^2$/g)$^{-1}$ day$^{-1}$ respectively. These values were lower than those in atmospheric pressure and room temperature. No diffence in the leaching rate with sea and distilled water was observed for the bitumen-waste products containing 40wt% salts. It appears that these results could be saved by improving safety in the dumping of sea. The effect of the softening point of pure asphalt or bitumen-waste product by $^{60}$ Co irradiation was increased with increasing total dose. Irradiation of asphalts at a total dose of 5.8$\times$10$^{8}$ rad showed no evidence of volume and caused no swelling. The functional groups of blown asphalt by infrared spectra are also identified.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.8 no.1
• /
• pp.9-17
• /
• 2010

The LCC (Liquid Cadmium Cathode) structure to be developed for inhibiting the formation and growth of the uranium dendrite has been known as a key part in the electrowinning process for the simultaneous recovering of uranium and TRU (TRans Uranium) elements from spent fuels. A zinc-gallium (Zn-Ga) experimental system which is able to be functional in aqueous condition and normal temperature has been set up to observe the formation and growth phenomena of the metal dendrites on liquid cathode. The growth of the zinc dendrites on the gallium cathode and the performance of the existing stirrer type and pounder type cathode structure were observed. Although the mechanical strength of the dendrites appeared to be weak in the electrolyte and easily crashed by the various cathode structures, it was difficult to effectively submerge the dendrite into the bottom of the liquid cathode. Based on the results of the aqueous phase experiments, a lab-scale electrowinning experimental apparatus which are applicable to the development of LCC srtucture for the electrowinning process was established and the performance tests of the different types of LCC structure were conducted to prohibit the uranium dendrite growth on LCC surface. The experimental results of the stirrer type LCC structures have shown that they could not effectively remove the uranium dendrites growing at the inner side of the LCC crucible and the performances of the paddle and harrow type LCC structure were similar. Therefore a mesh type LCC structure was developed to push down the uranium dendrites to the bottom of the LCC crucible growing on the LCC surface and at the inner side of the crucible. From the experimental results for the performance test of the mesh type LCC structure, the uranium was recovered over 5 wt% in cadmium without the growth of uranium dendrites. After completion of the experiments, solid precipitates of the bottom of the LCC crucible were identified as an intermetallic compound (UCd11) by the chemical analysis.

• Korean Chemical Engineering Research
• /
• v.50 no.4
• /
• pp.684-689
• /
• 2012

Poly(acrylic acid) (PAA) microspheres is one of the widely-used polymeric materials for the bio-field application and the electric materials. For the synthesis of PAA microspheres, the polymerization technique using surfactants is applied. After the synthesis, the purification and separation processes are required for the removal of surfactant. When general organic solvents were used, many problems, such as huge amount of waste solvent, additional separation processes, and the possibility of residual media, were occurred. Thus, High-pressure Soxhlet extraction using liquid $CO_2$ was developed to solve these problems. In this study, High-pressure Soxhlet extraction of the synthesized PAA microspheres using liquid $CO_2$ was conducted for the removal of Monasil PCA which is used for the dispersion polymerization of acrylic acid in compressed liquid Dimethyl ether (DME). The morphology of the extracted PAA particles was checked by field emission scanning electron microscopy (FE-SEM) and the residual concentration of Monasil PCA was analyzed by inductively coupled plasma - Optical Emission Spectrometer (ICP-OES). For studying the effect of the solvent effect, Soxhlet extraction was conducted using n-hexane, liquid DME, and liquid $CO_2$. In case of n-hexane, some extracted PAA microspheres were produced. However, deformation was also occurred due to the high thermal energy of n-hexane vapor. Liquid DME could not remove Monasil PCA. When using liquid $CO_2$, the extracted PAA microspheres which were free for the residual solvent were produced without deformation. For finding the optimum operating condition, high-pressure Soxhlet extraction was conducted for 8 hours with changing the temperature of reboiler and condenser. When the extractor temperature is $19.6{\pm}0.2^{\circ}C$ and the pressure is $51.5{\pm}0.5$ bar, the best removal efficiency was obtained.

• Journal of Korea Soil Environment Society
• /
• v.2 no.1
• /
• pp.83-90
• /
• 1997

Aiming at the treatment of large volumes of gas with a low concentration of poorly water soluble VOC(Volatile Organic Compound), a new system is proposed: the combination absorption tower/bioreactor. In the scrubber part of the bioscrubbing system, the contaminating compounds are absorbed in a aqueous phase. The contaminated scrubbing liquid is transported to the bioreactor, where the compounds are biodegraded by aerobic microorganisms (mainly to carbon dioxide, water, and biomass). In this study, separation of a volatile organic compound(VOC) out of a waste gas stream has been carried out using a re-cyclable high boiling point extrant(HBE). The liquid stream containing a high boiling point entrant(HBE) scrubs the gas stream in a direct gas-liquid countercurrent contacting operation in a packed tower for the removal of said component from the gaseous stream. A packed-bed column using Pall Ring was set up in order to simulate practical conditions for the scrubbing tower. The liquid stream transported to the bioreactor is recovered and recycled to the scrubber. The model gas, which contained 400 mg/$\textrm{m}^3$ of toluene, at a rate of 100 L/min, flowed into the packed column where the scrubbing liquid trickled over the packing in countercurrent to the rising gas at 10~15L/min. The bioscrubber designed for large volume air streams containing VOCs showed removal efficiency up to 80% in an optimum operating conditions during the tests fer removing toluene from an air stream by scrubbing the air stream with HBE.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.2
• /
• pp.68-74
• /
• 2005

The electrical arc furnace (EAF) classified as a special waste contains many flux components producing melts during a sintering process, so it decreases the sintering temperature and improves the mechanical properties of specimens. Increasing dust content in a clay-dust system brick, however, may cause the fraction defective higher due to the excessive liquid produced. To control the liquid behavior produced during sintering process for the clay-dust system specimens, the $Al_2O_3$ was added and the physical properties were analyzed. The microstructure for the clay-dust system body sintered with $Al_2O_3$ became homogeneous and the overall size of pores decreased. Adding $Al_2O_3$ to clay-dust system body increased the mechanical properties and the temperature of maximum strength increased as much as $50^{\circ}C$, and the apparent density increased and the absorption decreased. The mullite ($3Al_2O_3{\cdot}2SiO_2$) was produced during sintering process by reaction of $Al_2O_3$ and $SiO_2$ which could participate to liquid-producing-process and the viscosity of melts increased which was proved by measuring a critical viscosity temperature (Tcv) therefore, the refractoriness of specimens were improved to lower the fraction defective.

• Clean Technology
• /
• v.29 no.3
• /
• pp.185-192
• /
• 2023

This study was conducted to obtain basic process simulation data before conducting pyrolysis experiments for the development of a thermochemical conversion system by recirculation of heat carrier and gases thereby. In this study, polypropylene (PP) was used as a pyrolysis sample material as an alternative to waste plastics, and fluid sand was used as a heat transfer medium in the system. Manganese (Mn) was chosen as the catalyst for the pyrolysis experiment, and the catalyst pyrolysis was performed by impregnating it in the sand. The basic properties of PP were analyzed using a thermogravimetric analyzer (TGA), and liquid oil was generated through catalytic pyrolysis under a nitrogen atmosphere at 600℃. The carbon number distribution of the generated liquid oil was confirmed by GC/MS analysis. In this study, the effects of the presence and the amount of Mn loading on the yield of liquid oil and the distribution of hydrocarbons in the oil were investigated. When Mn/sand was used, the residue decreased and the oil yield increased compared to pyrolysis using sand alone. In addition, as the Mn loading increased, the ratio of C₆~C₉ range gasoline in the liquid oil gradually increased, and the distribution of diesel and heavy oil with more carbon atoms than C₁₀ in the oil decreased. In conclusion, it was found that using Mn as a catalyst and changing the amount of Mn could increase the yield of liquid oil and increase the gasoline ratio in the product.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.34 no.4
• /
• pp.389-393
• /
• 2001

For an effective utilization, quality stability of instant powdered oyster soup made of canned oyster processing waste water (IPSW) was determined. Instant powdered soup from oyster hot-water extracts (IPSE) was also prepared by mixing hot-water extract powder (15 g) with table salt (5 g), cream powder (19 g), milk replacer (12 g), wheat flour (20 g), corn flour (15 g), starch (5 g), glucose (7.5 g) and onion powder (1.5 g). In preparing IPSW, mixed powder from wash water and boiling liquid waste, instead of powder from hot-water extracts and table salt, was added (powder from boiling liquid waste: powder from wash water= 12: 8) and other additives were added in proportion to those in the IPSE. The moisture content, water activity, peroxide value and fatty acid composition showed little changes during storage of the IPSW. The pH, volatile basic nitrogen content and brown pigment formation increased slightly, while white index decreased slightly during storage of IPSW. No significant difference was observed in the changes of food component during storage between IPSW and IPSE. According to a sensory evaluation, the change in quality of IPSW was negligible during 12 months of storage. from the results of the chemical experiment and sensory evaluation, IPSW packed with laminated film bag (OPP, $20{\mu}m/PE,\;20{\mu}m/paper,\;45g/m^3/PE,\;20{\mu}\;m/Al,\;7{\mu}\;m/PE,\;20{\mu}m$) was revealed to be preserved in good quality during 12 months of storage.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.5
• /
• pp.549-557
• /
• 2006

The characteristics of supercritical water oxidation have been studied to decompose the waste anionic exchange resins which were produced from a power plant. The waste resins from a power plant were mixture of anionic and cationic exchange resins. The waste anionic exchange resins had been separated from the waste resins using a solid-liquid fluidized bed. It was confirmed that the cationic exchange resins were not included in the separated anionic exchange resins by the elemental and thermogravimetric analysis. A slurry of anionic exchange resins which could be fed continuously to a supercritical water oxidation apparatus by a high pressure pump was prepared using a wet ball mill. Although the COD of liquid effluent had been reduced more than 99.9% at 25.0 MPa and $500^{\circ}C$ within 2 min, the total nitrogen content was reduced only 41%. The addition of nitric acid to the slurry could reduce the total nitrogen content in treated water. The central composite design as a statistical desist of experiments had been applied to optimize the conditions of decomposing anionic resin slurry by means of the COD and total nitrogen contents in treated waters as the key process output variables. The COD values of treated waters had been reduced sufficiently to $99.9{\sim}100%$ af the reaction conditions of $500{\sim}540^{\circ}C$, 25.0 MPa within 2 min. The effects of temperature and nitric acid concentration on COD were not significant. However, the effect of nitric acid concentration on the total nitrogen was found to be significant. The regression equation for the total nitrogen had been obtained with nitric acid concentration and the coefficient of determination($r^2$) was 95.8%.