• Journal of the Korean Applied Science and Technology
• /
• v.29 no.2
• /
• pp.268-277
• /
• 2012

The thermal decomposition characteristic of waste PVC wires has been studied by using TGA and fixed-bed reactor. The experimental conditions of decomposition temperatures, air flow rates and weight ratio of CaO/PVC were considered in this work. To verify the effectiveness of CaO addition to remove HCl and toxic gases generated from thermal decomposition of PVC wire, the gaseous products obtained from the thermal decomposition of PVC were analyzed by GC/MS(Gas Chromatograph and Mass Spectrometry). To investigate the effect of CaO in thermal decomposition of PVC, liquid products were also analyzed by GC/MS. And the effect of decomposition temperature, air flow rate and CaO/ PVC weight ratio on the yield of liquid, gas and residue fraction have been also studied. From this work, it was found that the removal amount of HCl generated from thermal decomposition of PVC increased with increase of CaO addition.

• Journal of Environmental Science International
• /
• v.23 no.7
• /
• pp.1253-1268
• /
• 2014

This study was investigated twenty two hazardous chemicals compounds for effluents of nine sewage treatment plants (STPs) and one waste water treatment plant (WWTP) in the Nakdong Ri-ver Basin. They are eleven phthalates(DMP, DEP, DIBP, DBP, BEEP, DNPP, DHP, DCP, DEHP, DNOP, Dinonyl phthalate, seven aliphatic hydrocarbons(n-Tridecane, n-Tetradecane, n-Pentadecan-e, n-Hexadecane, n-Heptadecane, n-Octadecane, n-Nonadecane, Isoquinoline, 2-Chloropyridine, 2-N-itrophenol, and Benzophenone. The twenty two compounds were analyzed by gas chromatograp-hy mass spectrometry (GC/MS) with liquid-liquid extraction (LLE). Twenteen of twenty two subs-tances were detected. They were DMP, DEP, DIBP, DBP, DEHP, n-Tetradecane, n-Pentadecane, n-Heptadecane, n-Octadecane, n-Nonadecane, Isoquinoline and Benzophenone. Among these, DEHP, DEP and Benzophenone were most frequently observed. They were obtained as $ND{\sim}36.881{\mu}g/L$, $ND{\sim}0.950{\mu}g/L$, $ND{\sim}2.019{\mu}g/L$, respectively. When the substances were calculated the average concentration at 10 points, the maximum average detection concentration was investigated at the Dalseocheon STP.

• CELLMED
• /
• v.10 no.3
• /
• pp.19.1-19.6
• /
• 2020

The kidneys are exposed to toxicants and waste product and can be affected easily by these toxicants and by products of the metabolism. The consumption of adequate water is necessary to remove waste and to keep kidney healthy. Deficiency of liquid in the blood leads to various adverse effects on the kidney. The most common adverse deficiency of liquid in blood is deposition of solid matter in the kidney and subsequently formation of kidney stone. Nephrolithiasis (kidney stone) can be treated by drugs if it is small in size but if it blocks the route due to its big size then surgery is the only way to remove it. The recurrence rate of the problem is very high and it may reappear within 10 years. In Unani literature Hasāh wa Raml al-Kulya (nephrolithiasis) is described in detail. As per Unani literature stagnation of Ghalīz mādda (filthy and viscous matter) in the kidney is the main cause of the formation of kidney stone. Various single and compound formulations drugs are described for the management of kidney stone which are very effective as well as safe. Management is divided into two parts i.e. symptomatic treatment to relieve pain and to methods adopted to remove stone from the kidney. Musakkin-i-Waja'(analgesic) drugs are used for pain while Mufattit-i-Hasāh (lithotriptic) and Mudirr-i-Bawl (Diuretic) drugs are used to remove stone. Majoon Aqrab, Qurs Kaknaj and Dawa-e-Gurda etc. are compound drugs mentioned in literature for removal of kidney stone. Single drugs like Alu Balu, Tukhm Khayar, and Kharkhask etc. are also used for same purpose.

• Nuclear Engineering and Technology
• /
• v.53 no.4
• /
• pp.1210-1217
• /
• 2021

The analysis of ⁴¹Ca in concrete generated from the nuclear facilities decommissioning is critical for ensuring the safe management of radioactive waste. An analytical method for the determination of ⁴¹Ca in concrete is described. ⁴¹Ca is a neutron-activated long radionuclide, and hence, for accurate analysis, it is necessary to completely extract Ca from the concrete sample where it exists as the predominant element. The decomposition methods employed were the acid leaching, microwave digestion, and alkali fusion. A comparison of the results indicated that the alkali fusion is the most suitable way for the separation of Ca from the concrete sample. Several processes of hydroxide and carbonate precipitation were employed to separate ⁴¹Ca from interferences. The method relies on the differences in the solubility of the generated products. The behavior of Ca and the interfering elements such as Fe, Ni, Co, Eu, Ba, and Sr is examined at each separation step. The purified ⁴¹Ca was measured by a liquid scintillation counter, and the quench curve and counting efficiency were determined by using a certified reference material of known ⁴¹Ca activity. The recoveries in this study ranged from 56 to 68%, and the minimum detectable activity was 50 mBq g^-1 with 0.5 g of concrete sample.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2017.05a
• /
• pp.83-83
• /
• 2017

Electrorefining is a key step in pyroprocessing. The electrorefining process is generally composed of two recovery steps - the deposit of uranium onto a solid cathode and the recovery of the remaining uranium and TRU elements simultaneously by a liquid cadmium cathode. The solid cathode processing is necessary to separate the salt from the cathode since the uranium deposit in a solid cathode contains electrolyte salt. Distillation process was employed for the cathode processing. It is very important to increase the throughput of the salt separation system due to the high uranium content of spent nuclear fuel and high salt fraction of uranium dendrites. In this study, a mesh-covered crucible was investigated for the sat distillation of electrorefiner uranium deposits. A liquid salt separation step and a vacuum distillation step were combined for salt separation. The adhered salt in uranium deposits was efficiently removed in the mesh-covered crucible. The salt distiller was operated simply since repeated cooling - heating step was not necessary for the change of the crucible. The operation time could be reduced by the use of the mesh-covered crucible and the combined operation of the two steps. A method to preserve a vacuum level was proposed by double O-rings during the operation of the distiller with the mesh-covered crucible. After the salt distillation, the salt content was measured and was below 0.1wt% after the salt distillation. The residual salt after the salt distillation can be removed further during melting of uranium metal.

• Journal of Environmental Science International
• /
• v.16 no.3
• /
• pp.385-392
• /
• 2007

Currently, portable equipment for recycling of waste asphalt concrete (ASCON) has been used. However, any air pollution control devices are not attached in the simple portable one. Thus, a lot of air pollutants have been produced from recycling processes of waste ASCON which resulted from aging of paved roads or repavement of roads. This study deals with a preliminary result of concentration analysis of air pollutants obtained from a pilot and a real recycling processes of waste ASCON using simple portable recycling equipment. Air pollutants were taken from 4 steps of the pilot recycling process including an initial heating by liquid petroleum gas (LPG), intermediate heating and melting (H&M) process, final H&M process, and pavement processes using recycled ASCON at the recycling site. Also, air pollutants were taken front 4 steps of the real recycling processes including an initial H&M, final H&M and mixing, loading of recycled ASCON to dump trucks, and at the recycling site after leaving the loaded dump trucks for real pavement sites. The air pollutants measured in this study include volatile organic compounds (VOCs), aldehydes, particulate matter (PM: PM1, PM2.5, PM7, PM10, TSP (total suspended particulate)). The identified concentrations of VOCs increased with increasing time or degree for H&M of waste ASCON. In particular, very high concentrations of the VOCs at the status of complete melting, which is exposed to the air, of the waste ASCON just before paving tv the recycled ASCON at the recycling site. Also, considerable amount of VOCs were identified from the recycling equipment after the dump trucks leaded by recycled ASCON leaved the recycling site for the pavement sites. The relative level of formaldehyde exceeded 80% of the aldehydes Identified in the recycling processes. This is because the waste ASCON is exposed to direct flame of LPG during H&M processes. The PM concentrations measured in the winter recycling processes, such as the loading and rotation processes of waste ASCON into/in the recycling equipment for H&M, were much higher than those in the summer ones. In particular, the concentrations of coarse particles such as PM7 and PM10 during the winter recycling were very high as compared those during the summer one.

• Journal of Korea Society of Waste Management
• /
• v.35 no.8
• /
• pp.744-753
• /
• 2018

The Stockholm Convention, which was adopted in Sweden in 2001 to protect human health and the environment, includes regulations for Persistent Organic Pollutant Rotors such as toxic and bioaccumulatives. Currently, there are 28 types of materials. This prohibits and limits the production, use, and manufacture of products. Korea is a member of the Convention, and it is necessary to prepare management and treatment plans to address the POP trends. Thus, we experimentally investigate whether the environmentally stable incineration is achieved when the sample is thermally treated using the Lab-scale (1 kg/hr). The target samples is pesticides in liquid phase and solid phase. In this study, organic chlorinated pesticides and their thermal characteristics were analyzed. We calculated the theoretical air volume based on the element analysis results. Because the interior of the reactor is small, more than 10 times of the air ratio was injected. The retention time was set to at least 4 seconds using a margin. The incineration temperature was $850^{\circ}C$ and $1100^{\circ}C$. Thus, we experimentally investigated whether the environmentally stable incineration was achieved when the sample was thermally treated using the Lab-scale (1 kg/hr). We analyzed five types of exhaust gas; the 02 concentration was high, but the CO amount decreased. Complete combustion is difficult because of the small size of the furnace due to the nature of Lab-scale. The organic chlorine-containing pesticide had an average decomposition rate of 99.9935%. Considering the decomposition rates of organic chlorine-containing pesticide in this study, the incineration treatment at over 2 ton/hour, which is typical for a conventional incinerator, is possible. Considering the occurrence of dioxins and unintentional persistent organic pollutants, it can operate at more than $1,100^{\circ}C$.

• Applied Biological Chemistry
• /
• v.23 no.1
• /
• pp.64-72
• /
• 1980

Industrial wastes from pulp and food plants were treated with microorganisms to clarify organic waste-water and to produce cells as animal feed, and results were summarized as follows. (1) Waste-water from pulp, beer, bread yeast, and ethanol distillation plants contained $1.4{\sim}1.5%$ of total sugar, $0.25{\sim}0.35%$ nitrogen, and biological oxygen demand (BOD) was $400{\sim}25,000$, chemical oxygen demand (COD), $500{\sim}28,000$, and pH, $3.8{\sim}7.0$. The BOD and COD were highest in waste-water from ethanol distillation plants among others. (2) Bacterial and yeast counts were $4{\times}10^4-1{\times}10^9,\;2{\times}10^2-7{\times}10^4/ml$ in waste-water. (3) Bacteria grew better in pulp waste and yeasts in beer, bread yeast, and ethanol distillation waste. (4) Saccharomyces cerevisiae SAFM 1008 and Candida curvata SAFM 70 were the most suitable microorganisms for clarification of ethanol distillation waste. (5) When liquid and solid waste from ethanol distillation were treated with microbial cellulase, xylanase, and pectinase, solid waste was reduced by 36%, soluble waste was increased, and recuding sugar content was increased by 1.3 times which provided better medium than untreated waste for cultivation of yeasts. (6) Optimum growth conditions of the two species of yeast in ethanol distillation waste were pH 5.0, $30^{\circ}C$, and addition of 0.2% of urea, 0.1% of $KH_2PO_4$ and 0.02% of $MgSO_4$. (7) Minimum number of yeast for proper propagation was $1.8{\times}10^5/ml$. (8) C. curvata70 was better than cerevisae for the production of yeast cells from ethanol distillation waste treated with microbial enzymes. (9) S. cerevisiae produced 16 g of dried cell per 1,000ml of ethanol distillation waste and reduced BOD by 46%. C. curvata produced 17.6g of dried cell and reduced BOD by 52% at the same condition. (10) Yeast cells produced from the ethanol distillation waste contained 46-52% protein indicating suitability as a protein source for animal feed.

• Transactions of the KSME C: Technology and Education
• /
• v.3 no.4
• /
• pp.257-264
• /
• 2015

To maintain sustainability of nuclear energy as an important energy source, both safety problem and Spent Nuclear Fuels(SNFs) problem should be solved. In case of Gen-IV reactors such as fast reactor, SNFs can be used as fuels by using fast neutrons. It can be a suitable treatment method of high-level waste in near future. Liquid metals such as Sodium or Lead-Bismuth Eutectic (LBE) can be possibly used as a coolant to use fast neutrons. In this paper, it was described that natural circulation parameter studies, design analyses, material selections and a completion of facilities. To develop a natural circulation facility, thermal hydraulic analyses were performed. Installation technique of liquid metal natural circulation were secured.

• Journal of Korea Soil Environment Society
• /
• v.4 no.3
• /
• pp.95-104
• /
• 1999

Comparative biodegradation studies of liquid and solid alkanes and of two different solid alkanes were conducted by an isolated Acinetobacter sp., which degraded crude oil alkanes simultaneously. for the determination of degradation mechanism of hydrophobic crude oil constituents. Also a model oil experimental system composed of a solid alkane. heneicosane, as a substrate and a non-degradable non-aqueous phase liquid. pristane, as an oil matrix was established and studied. It was proposed that the Acinefobacter sp. utilized hydrophobic substrates directly on the surface of them with no difference in the degradation rates between the liquid and solid alkanes. On the basis of the results from the heneicosane/pristane system which imitates crude oil matrix containing solid constituents. the crude oil matrix was considered to reduce the bioavailability of contained substrates by reducing the specific surface area of substrates to contact with microorganisms.