• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.667-669
• /
• 2014

Development of 3 cylinder turbo charger engine is increasing due to engine down-sizing, cost reduction and emission regulations. However, 3 cylinder engine makes higher Exhaust manifold gas pressure(P3) pulsation than 4 cylinder engine and it generate boosting air with high pulsation. The mechanical waste-gate turbocharger just controlled by the boosting air has higher movement because of this high pulsation boosting air. This causes high vibrations to wasted gate and accelerate wear of the linkage system. So we need to understand out of the exhaust gas pressure pulsation changed by turbocharger compressor pressure(P2) Pulsation. In this study, we discuss how to prevent to abnormal movement of the turbo actuator by stabilized P2 Pulsation.

• 한국기계가공학회지
• /
• 제13권4호
• /
• pp.69-74
• /
• 2014

A waste gate valve (WGV) assembly for a gasoline turbocharger is typically manufactured by means of precision casting. In this study, however, it was newly manufactured in a more innovative way, metal injection molding (MIM) using Inconel 713C alloy, and its performance was tested in a 1.6L direct injection gasoline engine by a thermal shock durability test that lasted 300 hours, after which the results were compared to those of a precision-cast WGV assembly with regard to the engine intake boost pressure, turbine wheel speed, and transient intake pressure. It was found that the two WGV assemblies showed similar performance levels throughout the durability test.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2004년도 유체기계 연구개발 발표회 논문집
• /
• pp.680-686
• /
• 2004

Recently, the application of variable geometry turbocharger (VGT) to the high speed direct injection (HSDI) diesel engine has gained more and more interest in automotive industry. A steady state experimental investigation has been undertaken on a 1.5L HSDI diesel engine to verify the benefits of VGT comparing to the standard engine having a waste gate turbocharger (WGT). Specifically, part load performances (e.g., fuel economy and emission) have been investigated under various vane angles of the VGT. The results show that the real exhaust gas recirculation (EGR) rate as well as the pumping loss is very important to improve break specific fuel consumption (BSFC). It was previously known that the pumping loss only is a main parameter. In addition, the trade-off relationship between BSFC and NOx according to boost pressure, and the decreasing tendency of NOx with increasing real EGR rate have been verified. 1-D numerical analysis also has been performed, and the numerical results are in good agreement with experimental results.

• 한국자동차공학회논문집
• /
• 제24권4호
• /
• pp.392-400
• /
• 2016

In this paper, a study based on engine operating conditions versus hybrid excavator engines was conducted about the engine performance and fuel consumption via the 1-D engine simulation model. First of all, engine operating points with performance and emission were determined by driving patterns. The 1-D HFEM(High Frequency Engine Model) was developed for deep insight into engine combustion and the energy conversion phenomena. In accordance with changing operating points, especially High Idle and Rated output conditions, engine parameters and systems such as turbocharger(Waste Gate Turbocharger and Variable Geometry Turbocharger) injection strategies and EGR(Exhaust Gas Recirculation) should be considered. Therefore, various configurations and parametric analysis with optimization methods in hybrid excavator were simulated and optimized by NLPQL(Non-linear Programming by Quadratic Lagrangian algorithm) in 1-D HFEM. As a result, the fuel consumption with the developed hybrid electric excavator engine could be significantly decreased and bsfc(Brake Specific Fuel Consumption) was also reduced about 5 % to 7 % without any performance degradation.

• 한국연소학회지
• /
• 제21권4호
• /
• pp.1-5
• /
• 2016

The aim of this study is to compare the effectiveness of turbo chargers on engines for off-road use when combined with WGT and VGT technologies. The effectiveness of turbo chargers was measured and performance was compared using a functional model. Exhaust characteristics were compared using WGT and VGT technologies through a gas analyzer. Results showed VGT technology was more effective at high RPM compared to WGT technology. When it came to maximising turbo performance, VGT was more effective than WGT in every test. WGT and VGT produced similar exhaust NOx levels, whereas the VGT was more effective on the PM.

• 대한기계학회논문집B
• /
• 제36권2호
• /
• pp.217-224
• /
• 2012

비도로용 차량의 경우 대부분 디젤엔진을 사용하여 엔진의 특성상 PM과 NOx의 배출이 많은 단점이 있다. 승용 및 상용 디젤 차량의 경우 CRDI 및 후처리 장치를 적용하였고 후처리 장치로 DOC/DPF를 장착함으로써 PM은 약 90% 이상 저감 가능하다. 상반관계인 NOx는 EGR 사용을 통해 1차적으로 NOx 배출량을 감소시키고 LNT, LNC, Urea-SCR 등의 DeNOx 시스템으로 NOx의 배출량을 보다 현저히 저감시켜 배기규제를 만족시키고 있다. 본 연구에서는 tier 4 interim 배기규제를 만족하기 위해 56kW급 오프로드 차량으로 연구를 진행하였다. NOx의 감소를 위해 WGT와 전자 제어방식의 HPL EGR 시스템을 적용하였고 CO와 THC, PM 배출가스를 줄이기 위해 DOC와 DPF를 사용하였다. EGR 시스템을 적용하기 위해 각 조건에 대한 기본 실험을 실시하여 EGR map을 작성하였다. 작성된 map을 NRTC 모드에서 시험하여 map의 적용성을 검증하고 tier 4 interim 배기규제 만족여부를 파악하였다.