• 한국지능시스템학회논문지
• /
• 제13권4호
• /
• pp.403-408
• /
• 2003

캐리커처의 일반적인 의미는 어떤 사람이나 사물의 특징을 추출하여 익살스럽게 풍자한 그림이나 글이다. 다시 말해, 캐리커처는 사람의 얼굴에서 특징을 잡아 과장하거나 왜곡하여 그린 데생이라고 한다. 컴퓨터를 이용한 기존의 캐리커처 제작 방법으로는, 입력 이미지 좌표의 통계적인 차이 값을 이용하는 PICASSO 시스템 방법, 제작자의 애매한 느낌을 퍼지 논리를 이용하여 표현하는 방법, 이미지론 와핑하는 방법, 여러 단계의 벡터 필드 변환을 이용하는 방법 등이 연구되어 왔다. 본 논문에서는 실시간 또는 준비된 영상을 입력으로 받아 저장한 후, 네 단계의 과정으로 처리한 후 최종적으로 캐리커처 된 이미지를 생성하게 된다. 각 단계별 처리 내용으로는 첫 번째 단계에서는 영상에서 얼굴을 검출하고 두 번째 단계에서는 특정 얼굴부위의 기하학적 정보를 좌표 값으로 추출한다. 세 번째 단계에서는 전 단계에서 얻은 좌표 값으로 로컬 와핑 기법을 이용하여 영상을 변환한다. 네 번째 단계에서는 변형된 영상으로 퍼지 논리를 이용하여 보다 개선된 윤곽선 이미지로 변환하여 캐리커처 이미지를 얻는다. 본 논문에서는 영상 인식, 변환 및 윤곽선 검출 및 등의 여러 가지 영상 처리 기법을 이용하여 기존의 캐리커처 제작 방식보다 간단하고, 복잡한 연산 과정이 없는 캐리커처 제작 시스템을 구현하였다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 학회창립 10주년 기념 1999년도 가을 학술발표회 논문집
• /
• pp.429-432
• /
• 1999

The concrete slab on the foundation may have curling and warping deformations due to moisture and temperature gradient of its section. These deformations may change the support conditions of concrete slabs, and cause higher level of stresses than expected. This study was performed to verify the effect of partial support condition of concrete slab on the foundation due to its deformations and to develop the useful analytic method for describing these phenomenons. The partial support condition verified by FWD test results, and it was concluded that the gap model could be useful in analysing the concrete slab with partial support conditions.

• 대한토목학회논문집
• /
• 제43권5호
• /
• pp.577-585
• /
• 2023

횡비틀림 좌굴은 가설 중 붕괴 사고 등의 안전사고를 유발할 수 있기 때문에 설계단계에서 좌굴에 대한 정확한 안전성 검토가 이루어져야 한다. 횡비틀림 좌굴을 방지하기 위한 방안으로 단부 보강을 통해 거더의 뒤틀림 강도 증가시키거나 크로스 프레임 설치를 통해 비지지길이를 감소하는 방법 등이 있다. 크로스 프레임은 바닥판 합성 이후 구조적 역할이 적은 반면 재료비와 설치비에 따른 인건비 비중이 매우 크며, 용접부의 피로 균열로 인해 유지관리 성능을 감소시키는 요인으로 작용할 수 있다. 콘크리트 충전 반원기둥보강재를 통한 단부 보강 공법은 반원기둥 형태의 보강재를 통해 플레이트 거더의 단부를 보강하는 공법으로 거더 자체의 뒤틀림 강성을 증가시켜 횡비틀림 좌굴 강도를 증가시킨다. 이 연구에서는 콘크리트 충전 반원기둥보강재가 적용된 플레이트 거더의 뒤틀림 강도 증가로 인한 횡비틀림 좌굴 강도의 영향을 검토하기 위하여 설계식에 의한 결과와 유한요소해석의 결과를 비교하였고 실물재하실험을 통해 검증하였다. 설계식은 경계조건의 구속과 관련된 유효길이계수를 적용하고 있는 Eurocode의 설계식을 사용하였으며 결과를 검증하기 위하여다양한 단면의 유한요소해석을 수행하였다. 이후 횡방향 하중을 통해 뒤틀림을 받는 거더의 실물재하실험을 수행하여 콘크리트 충전 반원기둥보강재의 성능을 확인하였다. 그 결과 CFHPS가 적용된 플레이트 거더는 기존 판형 보강재가 적용된 플레이트 거더와 비교하여 뒤틀림 강도가 증가하였으며 그로 인해 횡비틀림 좌굴 강도가 증가하는 것으로 확인되었다.

• Steel and Composite Structures
• /
• 제3권2호
• /
• pp.111-122
• /
• 2003

The paper presents a model for analysing the shear-lag effect on the slab of twin-girder composite decks subjected to static actions, support settlements and concrete shrinkage, which are the main actions of interest in composite bridge design. The proposed model includes concrete creep behaviour and shear connection flexibility. The shear-lag in the slab is accounted for by means of a new warping function. The considered actions are then applied to a realistic bridge deck and their effects are discussed. The proposed method is utilised to determine the slab effective widths for three different width-length ratios of the deck. Finally, a comparison between the results obtained with the Eurocode EC4-2 and those obtained with the proposed model is performed.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 추계학술발표대회 논문집
• /
• pp.282-285
• /
• 2004

The main purpose of this study is the vibration suppression of rotating composite blade containing distributed piezoelectric sensors and actuators. The blade is modeled by thin-walled, single cell composite beam including the warping function, centrifugal force, Coriolis acceleration and piezoelectric effect. Further, the numerical study is performed m ing finite element method. The vibration of composite rotor is suppressed by piezocomposite actuators and PVDF sensors that are embedded between composite layers. A velocity feedback control algorithm coupling the direct and converse piezoelectric effect is used to actively control the' dynamic response of an integrated structure through a closed control loop. Responses of the rotating blade are investigated. Newmark time integration method is used to calculate the time response of the model. In the numerical simulation, the effect of parameters such as rotating speed, fiber orientation of the blade and size of actuators are studied in detail.

• 한국해양공학회지
• /
• 제6권2호
• /
• pp.103-112
• /
• 1992

The calculation method which takes into account the shear lag effects on the ultimate transverse bending moment of a SWATH(Small Waterplane Area Twin Hull) ship has been developed. In case of the ultimate bending strength analysis of conventional monohull ships and general box girder structures, the hypothesis that plane section remains plane after bending can be employed but not in the case of the structures having wide flange. For the ultimate bending strength analysis of such structures, a new method which can take into account the effect of shear lag on the ultimate bending strength has been developed by adopting more reasonable assumption that warping distortion of the section takes place inthe same way as the actual stress distribution. Finally, the proposed method has been applied to a a SWATH cross deck structure.

• 소음진동
• /
• 제6권4호
• /
• pp.431-438
• /
• 1996

The channel type structure which has large openings is frail with respect to torsional strength, and the horizontal-torsional motion is highly coupled, because of the large difference between the centroil and the shear center. Also, a discontinuous boundary phase is came from tansition section between the opened section and the closed section. To analyze the Bending- Torsional coupled mode parameters for the channel type structure, the Transfer Matrix Method was used. Comparing the result of F.D.M.T.M.M yields good results in relatively low frequency region.

• Structural Engineering and Mechanics
• /
• 제36권4호
• /
• pp.421-445
• /
• 2010

In this paper the formulation of an efficient frame element applicable for nonlinear analysis of 3D reinforced concrete (RC) frames is outlined. Interaction between axial force and bending moment is considered by using the fibre element approach. Further, section warping, effect of normal and tangential forces on the torsional stiffness of section and second order geometrical nonlinearities are included in the model. The developed computer code is employed for nonlinear static analysis of RC sub-assemblages and a simple approach for extending the formulation to dynamic cases is presented. Dynamic progressive collapse assessment of RC space frames based on the alternate path method is undertaken and dynamic load factor (DLF) is estimated. Further, it is concluded that the torsional behaviour of reinforced concrete elements satisfying minimum standard requirements is not significant for the framed structures studied.

• Structural Engineering and Mechanics
• /
• 제33권4호
• /
• pp.447-484
• /
• 2009

The spatially coupled buckling, in-plane, and lateral bucking analyses of thin-walled Timoshenko curved beam with non-symmetric, double-, and mono-symmetric cross-sections resting on elastic foundation are performed based on series solutions. The stiffness matrices are derived rigorously using the homogeneous form of the simultaneous ordinary differential equations. The present beam formulation includes the mechanical characteristics such as the non-symmetric cross-section, the thickness-curvature effect, the shear effects due to bending and restrained warping, the second-order terms of semitangential rotation, the Wagner effect, and the foundation effects. The equilibrium equations and force-deformation relationships are derived from the energy principle and expressions for displacement parameters are derived based on power series expansions of displacement components. Finally the element stiffness matrix is determined using force-deformation relationships. In order to verify the accuracy and validity of this study, the numerical solutions by the proposed method are presented and compared with the finite element solutions using the classical isoparametric curved beam elements and other researchers' analytical solutions.

• 한국가구학회지
• /
• 제19권4호
• /
• pp.294-299
• /
• 2008

Collapse is an abnormal shrinkage resulting in uneven, rough surfaces and/or warping of sawn timber. The maximum abnormal shrinkages of the oak and persimmon specimens were obtained by the quasi-equilibrium drying and were compared with the other drying methods. The effect of steaming and freezing treatments on the shrinkage of wood was also investigated. The Quasi-equilibrium drying used in this study was proved as a good tool to make the maximum abnormal shrinkage of wood. The maximum abnormal volumetric shrinkage possibly caused by collapse could be 16.3% and 14.3% for the oak and persimmon specimens, respectively. In general the steaming-treated specimens shrank less than the controls for the oak specimens, but did more for the persimmon specimens. The volumetric shrinkages of the freezing-treated specimens were more various between the drying methods than those of the control and steaming-treated specimens.