• 패션비즈니스
• /
• 제21권2호
• /
• pp.78-90
• /
• 2017

In this study, brassiere prototype was developed for attaching the measuring module of ECG measurement and body movement while sleeping. For ECG measurement, textile electrodes was made of stretch fabric containing polyurethane in consideration of elasticity of brassiere band. It was used as a conductive yarn by silver coating on the warp. The textile electrodes was woven with twisted twill to increase the density of conductive yarns. The pressure of the brassiere band was enough to sensing stably the ECG, and the elastic band of the brassiere was designed to be wider than 3cm to install the textile electrodes inside, so that textile electrodes was close fitting to the skin at a constant pressure without lifting. The textile electrodes coated with silicon on rear was attached to brassiere elastic band, and the module was installed with a snap connector to textile electrodes of brassiere band. The module was suitable to monitering ECG measurement of a typical R peak, pulse rate and body movement while sleeping without interfering.

• 한국의류학회지
• /
• 제28권9_10호
• /
• pp.1282-1291
• /
• 2004

Kenaf was cultivated and harvested in large quantity in Cheju Island and Chinju, Kyungsangnamdo. It was chemically rotted with 3% NaOH for 60 minutes at 100$^{\circ}C$, neutralized using 1% acetic acid, washed and dried, and obtained 40kg of dry kenaf fiber. Kenaf 15/rayon 85, flax 15/rayon 85, and rayon 100% yam was spun and the physical characteristics were measured. Plain weave and twill weave fabrics were made using each of the above yarns as the filling yam. Cotton 100% yam was used as the warp yam in all fabrics. Kenaf/rayon blend yarns were higher in tenacity and elongation, lower in yam uniformity, higher in the number of nep than the flax/rayon blended yams. Kenaf/rayon blend fabric had higher tenacity and elongation compared to the flax/rayon blend fabric Kenaf/rayon blend fabric was most stiff in both plain weave and twill weave fabrics whereas drape characteristics was dependent upon the fabric structure of the kenaf/rayon blend and flax/rayon blend. There were little differences between the kenaf/rayon blend fabric and the flax/rayon blend fabric in the Kawabata physical measurements and the PHVs. The only drawback of kenaf fiber was it's surface roughness and it is expected that it can be improved by enzyme retting and mechanical bundle separation.

• 한국게임학회 논문지
• /
• 제10권3호
• /
• pp.103-111
• /
• 2010

본 논문에서는 직물을 사실적으로 렌더링할 수 있는 절차적 접근법을 제안한다. 가상 직물을 렌더링하기 위한 기존의 절차적인 기법들은 결과의 사실성이 부족하다는 문제점이 있다. 이를 해결하기 위해 제안된 예제-기반 접근법은 렌더링의 사실성을 매우 높였지만, 다양한 재질의 반사를 표현하기 위해서는 대용량의 저장 공간이 필요하다는 단점을 가진다. 본 논문에서 제안되는 기법은 미세면(microfacet) 모델을 이용하여 직물을 표현한다. 미세면 모델은 이방성 반사특성을 갖도록 하였으며, 씨실과 날실은 이러한 이방성 반사 특성을 수직으로 교차하여 표현할 수 있다. 이와 함께 본 논문은 실을 더욱 사실적으로 표현하기 위해 직조물을 구성하는 실의 굴곡을 절차적으로 모델링하는 기법을 제안한다. 제안된 기법은 데이터를 사용하지 않고도 매우 사실적인 직물 렌더링이 가능하다.

• 보존과학회지
• /
• 제37권2호
• /
• pp.120-134
• /
• 2021

조선 말기 방한용 깔개인 모담(毛毯)이 창덕궁 성정각의 해체 공사 중 발견되었다. 문헌기록에 비해 현전하는 조선시대 모직물 유물이 많지 않아 유물로서 가치가 높다. 특히 1907년 창덕궁 성정각을 수리한 기록이 있어, 모담은 19세기 말 또는 20세기 초에 제작된 것으로 생각된다. 출토 모담은 자적색 계열의 바탕 직물로 위에 황색, 홍색 등으로 선염한 색사를 표면에만 삽입하여 문양을 시문하였다. 모담의 식서부분은 S연의 면사가 확인되었으며, 지경사는 Z연의 황마사, 지위사는 S연의 황마사, 문경사는 S연의 모사를 사용했다. 특히 무늬는 루프파일의 색사로, 색사의 경계면에서 일부 컷 파일이 확인되나 지위사로 고정되어 표면에 거의 드러나지 않는 다. 황마사와 모사를 사용한 것은 18세기 중엽 유럽의 브뤼셀 카펫의 영향을 받은 것으로 짐작된다. 모담의 문양을 밝히는 데 한계가 있으며 다만 문양이 부분적으로 반복됨을 알 수 있다. 이상의 연구내용을 도출하기 위해 문헌과 회화자료 외에 현미경 분석, 적외선 분광분석을 실시하였다. 또한 유물에 사용된 염료를 밝히기 위해 색도측정을 토대로 자외-가시광 분광분석을 실시하여 천연 염색한 직물 샘플에 대한 교차분석을 시도하였다. 그 결과 모담의 녹색 모사는 쪽을 사용하지 않았으며, 자적색의 바탕조직은 소목으로 염색한 것으로 추정할 수 있다.

• 한국의류산업학회지
• /
• 제2권2호
• /
• pp.150-158
• /
• 2000

This study investigated mechanical properties, drape coefficients and node indices of stretch fabrics. We applied mechanical properties to exhibited tailorability control in HESC and evaluated making-up. The mechanical properties such as tensile, bending, shearing, compression, surface characteristic values, thickness and weight were measured by the KES-F system and drape coefficient by drape tester. The summarized results of this study were as follows; First, stretch fabrics, almost, shown high stretch in weft inserted polyurethane yarn fabric and had a ${\pm}2{\sigma}$(sigma) range of shearing, compression, surface and thickness, except bending and weight, as compared with Japanese women's thin dress fabrics. Second, bending had a positive correlation in stiffness, anti-drape and flexibility & softness. Shearing had a negative correlation in crispness and scroop. Surface properties had a high contribution in fullness & softness. Third, The drape coefficient was found by measuring the mechanical properties according to the obtained regression equation. Forth, many problems are expected in overfeed and cutting operations in sewing process. In the decision of the good external appearance using TVA, only 26 of 55 samples are included in the range of the good external appearance. Fifth, in the regard of the result for sewing control, warp values are not necessary to control in the all kind of items. But weft value in the RT and EM are out of non-control zone. So we need a special management during sewing process.

• 복식
• /
• 제36권
• /
• pp.53-75
• /
• 1998

The kind, the structure, and the motif of the Chosun dynasty's fabrics found mainfy within the Buddhist statues were studied. The total of 62 pieces of fabrice can be classified chronologically as follows ; 27 pieces in the year of 1431, 20 pieces of 1550, 9 pieces of 1664, and 6 pieces of 1735. These 62 fabrics also categorized by the weaving method as follows; 27 plain weaved, 17 twill weaved, 10 pieces of satine weaved, 7 pieces of Leno weaved, and 1 piece of double weaved fabrics. Most of the studied fabrics were silk, the rest were 2 pieces of yam and 1 piece of cotton, Kyun, Chu, and Cho were the plain weaved silk as Nung and Ki were the twill weaved silk, Satine weaved silk was called as Dan and double weaved silk was called Chikum in the Chosun dynasty. 1. The antique fabrics were composed of mainly silk. This is believed due to the utmost devotion to the buddhist statue as an object of worship. 2. In the fabric's structural point of view, th ecrossed 4-ply threads of warp yarn which is one of Leno weaved can be observed fre-quently in the period of Korea dynasty's fabrics. But it started to disappear in the beginning of Chosun dynasty, since only one piece of Ra could be found in the 1431's fabrics. Keum, one of the double weaved structure is assumed to be extinct from the Korea dynasty. Satin weaved fabrics started to be woven from the latter period of Korea dynasty and was very popular in Chosun dynasty. 3. The widths of fabrics in the Chosun dynasty gradually decreased compared with those of Korea dynasty.

• 한국의류학회지
• /
• 제25권1호
• /
• pp.173-182
• /
• 2001

The physical properties and biodegradability of cellulose fabrics, such as cotton and rayon, are expected to vary with textile care. In this study cotton and rayon fabrics were washed repeatedly with detergents, bleaches, or softeners. The changes of physical properties were investigated by measuring retention of breaking strength, shrinkage, handle, and the fiber surface was observed by SEM. The biodegradability of fabrics was also estimated by soil burial test. The results were as follows. Cotton fabrics laundered repeatedly by detergents and bleaches lost virtually no strength. The breaking strength of the rayon fabrics decreased by about 17%∼25% after repeated launderings. Shrinkage in weft direction was much larger than that in warp direction. Bending rigidities of both fabrics decreased remarkably within 10 wash cycles. Shear rigidity in cotton fabrics increased continuously with repeated washing cycles, however, that in rayon fabrics did not show any change as washing went on. Friction coefficient increased in both fabrics after 10 wash cycles, and this is thought to be attributed to the wrinkle, interlocking of hairs, surface damage resulted from repeated washings. In cotton fabrics made of staple yarns, short hairs on the yarn surface entangled together with repeated launderings. This resulted in the continuous increase in % shrinkage, shear rigidity, friction coefficient. Rayon fabrics made of filament yarns, however, did not show this phenomenon. Softener treated fabrics showed the lowest values in bending rigidity, shear rigidity and friction coefficient because the cationic surfactants adsorbed on the fiber surface behaved like lubricants. The biodegradability of fabrics was noticeably affected by the composition of washing solutions. The fabrics washed with detergents and bleaches were decomposed faster than those washed with the others were and the cotton fabrics washed with detergents and softeners hardly degraded. The fabrics soiled with milk were decomposed almost completely and those soiled with Palmitic acid did not degrade greatly.

• 한국산업융합학회 논문집
• /
• 제8권1호
• /
• pp.11-17
• /
• 2005

This study was performed to analysis the operation process when fabric pattern design was done by the use of CAD system compared with the manual work in order to determine the operation efficiency with the application of fabric design CAD system. The results of the study were as follows: 1. since 160,000 colors were supported by CAD system, color proposed by consumer was able to match exactly according to the its design. However, exact color matching was not possible by manual work. 2. Woven state of back of pattern design could be identified simultaneously with face of it for CAD system, while face and back of the fabrics should be designed separatedly in case of manual work. 3. Since the combination of warp and filling yarn was compatible with the fabric density in one repeat unit in CAD system, exact size of pattern design to be woven was able to expressed. 4. Only simple graphical expression by manual work was seen, while with the CAD system, texture and shade effect as well as graphical expression could be expressed and so fault could be reduced in advance with the simulation of actual feeling of fabrics in the screen. In conclusion, when CAD system will be introduced to the textile industry, operation time of designing pattern can be reduced. Since the operation is easy and simple, a beginner can operate CAD system easily. Thus, production and wage costs can be saved and this can be related directly with the improvement of productivity which is the main purpose of introducing CAD system.

• 패션비즈니스
• /
• 제8권5호
• /
• pp.31-40
• /
• 2004

The purpose of this study is to investigate the change of the physical properties, bending and luster properties, which are related to the touch and appearance of silk fabrics modified by the degumming process. The silk has long been known as one of the most elegant and soft textile materials. The raw silk yarn, or cocoon bave, spun from the spinneret, is rather stiff due to the sericin covering the two fibroins together. The sericin can be removed during a degumming process. The removal of the sericin would result in remarkable change in the physical properties of the raw silk fabrics, including luster of the fabrics, which process parameters could possibly be utilized to adequately control the silk fabric properties. The KES(Kawabata Evaluation System) is a testing methodology that has been used with considerable success for predicting the hand and tailorability of apparel fabrics. This study uses one of the KES, bending tester, to measure the bending properties of the silk fabrics degummed for specified period to change the physical/mechanical properties of the fabric. The KES bending measurement revealed that the bending rigidity decreased for both the warp and weft direction of the silk fabrics with the increase of the degumming period. It has been shown in this study that the some of the hand-related physical properties, including the bending rigidity, drapability, and luster, could be modified with the change in the degumming period.

• 한국염색가공학회지
• /
• 제13권2호
• /
• pp.120-127
• /
• 2001

In order to make a microfiber fabric with PET/Co-PET Sea-Island Type microfiber, the optimum condition of extraction and elimination of Co-PET from the mocrofiber was examined. At the same time, the physical property change of the fabric with respect to the change of the relative amount of the Co-PET in the microfiber was also examined to provide a directly applicable data set to the industry. The sample fabric used was warp 75/36(DTY) and weft 0.05d(PET/Co-PET, Sea Island Type Microfiber) twill fabric of 36 separated yarns＋40/24(high shrinking yarn) with 130/48 ITY. The data set was made at various NaOH concentrations and steam temperatures with time as a main variable. The physical properties examined were the tensile properties. The results obtained were the tensile. The results obtained were 1. For a proper extraction of Co-PET (13.5%)from the microfiber with wet curing, it takes more than 5 min. in 8 and 12% of NaOH solutions but it takes only 3 min. in 18% of NaOH solution at 12$0^{\circ}C$. 2. For a proper extraction of Co-PET (13.5%) from the microfiber with wet curing, ti takes 3~5min. in 12 and 14% of NaOH solution and it takes less than 3 min. in 18% of NaOH solution at $130^\circ{C}$. 3. The increasing ratio of WT increased with increasing NaOH concentrations and the equilibrium point reached was 3 min. at $120^\circ{C}$. 4. The WT increasing ratio was greater in 14 and 18% NaOH solutions than in 8 and 12% of NaOH solutions at $130^\circ{C}$5. The RT ratio changes at $120^\circ{C}$ in 8 and 12% of NaOH solutions were indifferent from that at $130^\circ{C}$ in 12% of NaOH solution. However, the RT was apparently decreased with increasing NaOH concentration.