• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.37 no.1
• /
• pp.45-51
• /
• 2001

In order to investigate the optimal design weight of sinkers for preventing cage net from deforming in current, the model experiment on 2 types of square cage nets with different S sub(n)/S, the ratio of total area of netting projected to the perpendicular to the water flow S sub(n) to wall area of netting S, and 4 kinds of sinkers was carried out in circulation water channel. The model cage nets were made in 1/10 scale and the total weight in water of 4 sinkers attached to each corner of their bottom frames was 18, 54, 90, and 126g, respectively equivalent to 0.1, 0.3, 0.5, and 0.7 kg per unit area of prototype net. The results obtained can be summarizes as follows; Due to the deformation of each net where it was lifted towards the surface in severe conditions, its volume was reduced. This depended highly on the weight of sinkers placed in the bottom corner of cage nets, even if the variation of S sub(n)/S had a little effect on their deformation in current less than 0.4 m/s. In addition, it was observed that the total weight of sinkers for preventing the net from deforming to the extent of less than 50% inside its initial volume was 31 to 245 kg in the range of 0.3 to 0.6 m/s and the adequate design weight of sinker was approximately 0.5 kg per its unit area.

• 한국해양학회지
• /
• v.25 no.2
• /
• pp.62-73
• /
• 1990

An experimental study is performed in order to catch the characteristics of the flow field at arrested salt wedge, using a rectangular open channel. Arrested salt wedge is generally so stable that the observations are easy, but velocities and interfacial waves are measured with the aid of visualization method, by injection of fluorescent dyes. The density interface, which is defined as the zone of maximum density variation with depth, exists in about 0.5 cm below the visual interface, and vertical density profile is quite well satisfied with Homeborn model. Interfacial layer has high turbulent intensity and its thickness decreases as the overall Richardson number increases and has magnitude of roughly 17% of upper layer. Cross-sectional velocity distribution just shows the influence of a side-wall friction and in the upper layer vertical velocity profile also becomes uniformly as Reynolds number increases, but in the lower layer it shows nearly parabolic type. Supposes that we divide salt wedge into three domains, that is, river mouth, intermediate and tip zone, entertainment coefficient is small at the intermediate zone and large at the river mouth and the tip zone. River mouth or intermediate zone has comparatively stable interface and capillary wave therefore s produced and propagated downstream. On the other hand, tip zone is very unstable, cusping ripple or bursting ripple is then produced incessantly. Arrested salt wedge form is nearly linear and has no relation to densimetric Froude number and Reynolds number.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.5 no.1
• /
• pp.59-67
• /
• 2017

The objective of this paper is to investigate experimentally the effect of replacement of recycled coarse aggregates with 5~13mm in size on a field applicability of concretes through Mock-up test. Seven different mock-up specimens were prepared with the size of $1200{\times}800{\times}800mm$ simulating column and wall. For the concrete mixtures, 24MPa, 27MPa and 40MPa of nominal strength were adopted with 30% and 70%(only for 24MPa) of 5~13mm recycled coarse aggregate (RCA) replacement and without 5~13mm RCA(Plain). For test items, slump, slump flow, compressive strength with different curing conditions, core drilling, rebound numbers and drying shrinkage were measured. Test results indicated that 30% of 5~13 mm RCA replacement resulted in increase in slump, slump flow and resistance against segregation, while air contents decreased compared to those of plain mixture. Compressive strength of concrete with 30% of 5~13mm RCA was shown to be higher than that of plain mixture due to optimum packing effect associated with presence of well graded aggregates. Rebound number of the mock-up specimen with 30% of 5~13mm RCA had lower fluctuation according to hitting location than that of plain mock-up specimen. It is believed from the results of the study that replacement of 30% of 5~13mm RCA brings desirable improvement in various aspect of concrete performance due to associated dense packing effect.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.10 no.1
• /
• pp.1377-1387
• /
• 1968

In order to measure runoff and soil losses produced in a small test plot during rainfall, it is usually insufficient to use a tank only, necessitating the combined use of a main tank and a subsidiary tank. Accordingly. exact measurement largely depends on how to connect those two measuring tanks. The main purpose of this thesis is to improve the connecting parts of two measuring tanks so as to assure exact measurement of runoff and soil losses. In this experiment, two types of main tank, i. e. A-type and B-type, were used. A-type is a square tank having a flume at its end. At the flume, ten apertures are provided by using metal columns so as to be able to catch one tenth of total muddy flow discharging at the end of the flume, One tenth of total flow is led to the subsidiary tank through a slot sampler fixed to an aperture. B-type differes in that its flume does not have apertures and slot sampler is fixed directly to the end of the flume, other features being the same as those of A-type. Discharge volumes were measured by using weighing tanks and compared. The effect of baffle screen provided in the flume was also observed in connection with exact measurements. In order to keep main tank and its flume in a horizontal position, bolts and nuts mechanism was used. Vertical and horizontal screens were provided in the main to prevent coarse sands coming into the flume. The conclusion derived through this experiment is as follows: (1) The discharge through slot sampler at each aperture is almost the same for A-type. However, it is slightly more than one tenth of total discharge volume. (2) In case that baffle screen is provided in the flume of A-type tank, the discharge volume of slot sampler is less than that of the same type without screen. (3) For B-type tank, slot sampler discharge increases as slot sampler nears toward the center of flume. (4) When baffle screen is provided in the flume of B-type, slot sampler discharge is less than that of the same type without screen, and this phenomenon is more apparent as compared with A-type. (5) In case that the slot width of slot sampler for B-type is one inch, slot sampler discharge exceeds one tenth of total discharge volume. (6) When the slot width for B-type is 15/16 inch and slot sampler is fixed 3/8 inch apart from either flume wall, slot sampler discharge is approximately equal to one tenth of total discharge volume.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.12
• /
• pp.476-481
• /
• 2016

Steam power generation is used to produce electricity through a generator that is connected to a steam turbine. As a result, the surface temperature of the deaerator is $70^{\circ}C$during the summer season, the surface temperature of the storage tank is $67^{\circ}C$, and the air temperature is $50^{\circ}C$. This environment is inappropriate for workers and instruments. Workers adjacent to the deaerator and storage tank in particular feel higher temperatures because of the radiative heat transfer effect. Therefore, we optimized the cooling conditions by computational analysis. Case 1 is the current shape of the power plant, Case 2 has additional insulation, and Case 3 has a radiation shield. Flow is caused by a temperature difference between the heat sources in the wall, and hot air is trapped in the right upper end. Based on the temperature contours and the maximum temperature of the surfaces, Case 2 was found to be the most efficient for reducing radiative heat transfer effects.

• Korean Chemical Engineering Research
• /
• v.44 no.5
• /
• pp.513-519
• /
• 2006

We developed two kinds of the microchip for application to electrophoresis based on both glass and quartz employing the MEMS fabrications. The poly-Si layer deposited onto the bonding interface apart from channel regions can play a role as the optical slit cutting off the stray light in order to concentrate the UV ray, from which it is possible to improve the signal-to-noise (S/N) ratio of the detection on a chip. In the glass chip, the deposited poly-Si layer had an important function of the etch mask and provided the bonding surface properly enabling the anodic bonding. The glass wafer including more impurities than quartz one results in the higher surface roughness of the channel wall, which affects subsequently on the microflow behavior of the sample solutions. In order to solve this problem, we prepared here the mixed etchant consisting HF and $NH_4F$ solutions, by which the surface roughness was reduced. Both the shape and the dimension of each channel were observed, and the electroosmotic flow velocities were measured as 0.5 mm/s for quartz and 0.36 mm/s for glass channel by implementing the microchip electrophoresis. Applying the optical slit with poly-Si layer provides that the S/N ratio of the peak is increased as ca. 2 times for quartz chip and ca. 3 times for glass chip. The maximum UV absorbance is also enhanced with ca. 1.6 and 1.7 times, respectively.

• Journal of the Korean Applied Science and Technology
• /
• v.37 no.1
• /
• pp.83-90
• /
• 2020

Plate heat exchangers(PHE) have been commercialized since the 1920s. Since then, although the basic concept of PHEs has changed little, its design and construction have progressed significantly to accommodate higher temperatures, higher pressures, and large heat exchanging capacities. The development trend of PHEs is consistent with heat plate developments with better thermal efficiency, lower pressure drop, and good flow distribution. The purpose of this paper is to introduce the main development processes of a plate cooler for medium-speed engine lubricant oil cooling in vessels which is in line with the development trend of PHEs and to provide its thermal performance data that were found out during experimental tests. The plate cooler in this study cannot measure the wall temperatures directly due to its structural characteristics, so the heat transfer coefficients were calculated using the modified Wilson Plot method. The water-to-water tests were first conducted experimentally to figure out the characteristics of heat transfer coefficients and pressure drops on the water side and then the water-to-oil tests followed to obtain the heat transfer coefficients on the oil side. The test results showed that heat transfer coefficients and pressure drops on both water and oil side increased with flow rates, and it was also found that all the development targets of the plate cooler in this study were achieved successfully.

• Journal of Biomedical Engineering Research
• /
• v.23 no.6
• /
• pp.467-475
• /
• 2002

Hyperthermia using transrectal thermal probes has been used for a noninvasive treatment of prostate diseases. However it is known that heating the rectal wall at excessively high temperature can lead to destruction of the rectal mucous membrane. and it is difficult to maintain an optimum temperature over the entire prostate. Thus, a more accurate understanding of the heat transfer mechanism between prostate and hyperthermia system is needed Numerical analysis was performed to investigate how the cold/warm stimulations on the prostate surface affect the temperature distribution in the prostate model. The general purpose software "FLUENT" was used for obtaining a finite volume solution to the unsteady conduction equation and to calculate the time-varying temperature in the prostate. Effects of the warm/cold stimulations and the stimulation frequency on the temperature distribution were simulated. and we visualized how hyperthermia affected the inside of the prostate. It was found that the effect of hyperthermia by using a typical heating method is limited due to the low thermal conductivity of the prostate. Consecutive repetitions of warm and cold stimulations were considered to provide the thermal irritations inside a prostate. The effects of temperature difference and duration of warm/cold stimulations were investigated, and basic data for the optimum period and effective patterns of stimulations were obtained. A simplified bioheat equation was also solved to describe effects of the blood flow on the blood-tissue heat transfer. The effect of blood flow was not dominant compared to that of warm/cold stimulations. These results might be used as data for design of prostate treating probe, prostatic therapy and thermal stimulation effects on the prostate.

• Tunnel and Underground Space
• /
• v.11 no.3
• /
• pp.257-269
• /
• 2001

Numerical simulation is performed to understand the structural behavior of an underground radwaste repository, assumed to be located at the depth of 500 m, in a granitic rock mats, in which a fault intersects the roof of the repository cavern. Two dimensional universal distinct element code, UDEC is used in the analysis. The numerical model includes a granitic rock mass, a canister with PWR spent fuels surrounded by the compacted bentonite inside the deposition hole, and the mixed bentonite backfilled in the rest of the space within the repository cavern. The structural behavior of three different cases, each case with a fault of an angle of $33^{\circ},\;45^{\circ},\;and\;58^{\circ}$ passing through the cavern roof-wall intersection, has been compared. And then fro the case with the $45^{\circ}$ fault, the hydro-mechanical, thermo-mechanical, and thermo-hydro-mechanical interaction behavior have been studied. The effect of the time-dependent decaying heat, from the radioactive materials in PWR spent fuels, on the repository and its surroundings has been studied. The groundwater table is assumed to be located 10m below the ground surface, and a steady state flow algorithm is used.

• Journal of Chest Surgery
• /
• v.33 no.8
• /
• pp.605-612
• /
• 2000

Background: Ischemic preconditioning enhances the tolerance of myocardium against ischemia/reperfusion injury, with the enhancement of the recovery of post-ischemic myocardial function. This study was disigned to assess whether the protective effect of ischemic preconditioning could provide one additional hour of myocardial preservation in four hour myocardial ischemia in a rate heart. Material and method: Fourty four Spargue-Dawley rats, weighing 300~450gm, were divided into four groups. Group 1(n=7) and group 3(n=12) were subjected to 30 minutes of aerobic Langendorff perfusion without ischemic preconditioning and then preserved in saline solution at 2~4$^{\circ}C$ for 4 hours and 5 respectively. Group 2(n=7) and group 4(n=18) were perfused in the same way for 20 minutes, followed by 3 minutes of global mormothermic ischemia and 10 minutes of perfusion and then preserved in the same cold saline solution for 4 hours and 5 hours respectively. Heart rate, left ventricular developed pressure(LVDP), and coronary flow were measured at 15 minutes during perfusion as baseline. Spontaneous defibrillation time was measured after reperfusion. Heart rate, LVDP, and coronary flow were also recorded at 15 minutes, 30 minutes, and 45 minutes during reperfusion. Samples of the apical left ventricular wall were studied using a transmission electron microscope. Result: Time of spontaneous defibrillation(TSD) was significantly longer in group 4 than in group 1(p<0.001), and TSD in group 1 was significantly longer in comparision to that of group 2(p<0.05). Heart rate at 45 minutes was significantly higher in group 1 than in group 4(p<0.05). Heart rate at 15 min was significantly higher in group 2 than in group 1(p<0.001) and in group 4 than in group 3(p<0.05). Left ventricular developed pressure(LVDP) at 30 minutes and 45 minutes was higher in group 1 than in group 4(p<0.01), LVDP at 45 minutes was higher in group 4 than in group 3(p<0.05). Rate-pressure product(RPP) at 30 minutes and 45 minutes was higher in group 1 than in group 4(p<0.05). RPP at 15 minutes was higher in group 2 than in group 1(p<0.01). RPP at 30 minutes and 45 minutes was higher in group 4 than in group 3(p<0.05). Group 2 showed relatively less sarcoplasmic edema and less nuclear chromatin clearance than group 1. Group 4 showed less myocardial cell damage than group 3, group 4 showed less myocardial cell damage than group 3, group 4 showed more myocardial cell edema than group 1. Conclusion: Ischemic preconditioning enhanced the recovery of postischemic myocardial function after 4 hours and 5 hours preservation. However, it was not demonstrated that ischemic preconditioning could definitely provide one additional hour of myocardial preservation in four hour myocardial ischemia in a rat heart.