• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.2
• /
• pp.294-302
• /
• 1997

Falling-film evaporation experiments for aqueous solution of lithium bromide (LiBr) were performed on a horizontal smooth 19.05-mm-dia copper tube. Average heat transfer coefficients were obtained with varied film Reynolds numbers, system pressures, LiBr concentrations and degrees of wall superheat. Heat transfer coefficients increase with increasing system pressure and decreasing concentration. For degrees of wall superheat, the heat transfer coefficient did not't show the distinct trend. For this experimental ranges, heat transfer coefficients showed maximum values at an optimal film Reynolds number. The results of this work were compared with pool boiling data reported previously, and it was shown that the heat transfer performance is superior to the pool boiling.

• International Journal of Fluid Machinery and Systems
• /
• v.2 no.1
• /
• pp.55-60
• /
• 2009

The present study investigated temperature and thermal stress distributions in a film cooling system with normal injection cooling flow. 3D-numerical simulations using the FEM commercial code ANSYS were conducted to calculate distributions of temperature and thermal stresses. In the simulations, the surface boundary conditions used the surface heat transfer coefficients and adiabatic wall temperature which were converted from the Sherwood numbers and impermeable wall effectiveness obtained from previous mass transfer experiments. As a result, the temperature gradients, in contrast to the adiabatic wall temperature, were generated by conduction between the hot and cold regions in the film cooling system. The gradient magnitudes were about 10~20K in the y-axis (spanwise) direction and about 50~60K in the x-axis (streamwise) direction. The high thermal stresses resulting from this temperature distribution appeared in the side regions of holes. These locations were similar to those of thermal cracks in actual gas turbines. Thus, this thermal analysis can apply to a thermal design of film cooling holes to prevent or reduce thermal stresses.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.14 no.4
• /
• pp.140-144
• /
• 2004

CdTe thin films were grown on GaAs (100) substrates by hot wall epitaxy method. From the XRD measurements, it was found that CdTe/GaAs (100) film was grown as a single crystals with the different from growth plane of (III), and growth rate of CdTe thin films was found to be 30 $\AA/sec$ by SEM. To acquire a high quality CdTe thin film, the optimum temperature for the source and substrate are found to be $500^{\circ}C$ and $320^{\circ}C$, respectively, which was checked by PL.

• Journal of ILASS-Korea
• /
• v.1 no.4
• /
• pp.24-31
• /
• 1996

This study addresses the behavior characteristics of diesel spray injected on the impinging disk with the room temperature. The models of impinging spray are the stick, the reflect and the wall jet model In the initiative of the fuel injection the impinging spray was the reflect model. because the momentum of droplets was very large. This model developed to the wall jet model according to the time approaches. On the low temperature disk the fuel film was made by the attachment of the droplets with low Weber number. The thickness of impinging spray was increased when the disk approached to the nozzle tip. Mathematical analysis for calculation with the behavior of impinging spray have to consider the reflecting effect and the influence of the fuel film.

• Journal of the Korean Institute of Navigation
• /
• v.25 no.4
• /
• pp.435-442
• /
• 2001

A new technique to grow a manganese-doped zinc-sulfide(ZnS：Mn) has been proposed using the repeated deposition of the Hot Wall method. The optical characteristics and crystallinity for the ZnS and ZnS：Mn thin films deposited on a quartz glass substrate by the method were investigated. Also, The ZnS：Mn thin film elcetroluminescent devices were fabricated by the method to study luminescence characteristics. All films showed (111)-oriented cubic structure. By the repeated deposition, the deposition rates were decreased, and the optical characteristics and crystalline properties were improved, which clarifies that the method is effective to deposit the thin films with good crystallinity Futhermore, the crystallinity was more improved by the doping of Mn. Only one peak emission at around 585nm originating from Mn luminescent center is observed In the photoluminescent and electroluminescent spectra of ZnS：Mn films and the luminance of the ZnS：Mn-based thin film electroluminescent devices was obtained below 60cd/$m^2$ . The optical and crystalline properties, luminescence characteristics are discussed in terms of the effects of the repeated deposition and Mn-doping.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.6 no.4
• /
• pp.453-462
• /
• 1994

An unsteady quasi one-dimensional model of momentum, heat and mass transfer in a falling film of a vertical plate absorber which is cooled by air was developed using the integral method. Energy conservation of the absorber wall is considered in the model. The model can predict absorption rate, film thickness and mean velocity as well as concentration and temperature profiles. Predictions of steady state temperature and concentration profiles for LiBr/water system for constant wall temperature condition are in good agreement with the two-dimensional finite difference method solutions. Effects of operating conditions, such as convective heat transfer coefficient between the cooling air and the absorber wall, cooling air temperature and film thickness at inlet, on absorption rate of water vapor into LiBr/water solution were shown.

• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.12
• /
• pp.1209-1214
• /
• 2006

This paper presents an application of Dividing Wall Column(DWC) to the recovery of the waste solvent from the film making processes. The waste solvent feed contains MEK(Methyl-Ethyl-Ketone), Toluene, Cyclohexanone, and water. The commercial software $HYSYS^{TM}$ was used for rigorous simulation and analysis. Sensitivity analysis for several major design variables were carried out to achieve the optimal design of the process. Distribution of the internal vapor and liquid flows to the prefractionator and main sections is shown to be the most dominant design factor for energy saving efficiency in the DWC process. The simulation results also show that the solvent recovery process using the DWC significantly improves both the energy efficiency and the compactness of the solvent recovery process.

• Journal of the Korean Vacuum Society
• /
• v.4 no.S1
• /
• pp.190-195
• /
• 1995

The feature scale model for selective chemical vapor deopsition process was proposed and the simulation was performed to study the selectivity and uniformity of deposited thin film using Monte Carlo method and string algorithm. The effect of model parameters such as sticking coefficient, aspect ratio, and surface diffusion coefficient on the deposited thin film pattern was improved for lower sticking coefficient and higher aspect ratio. It was revealed that the selectivity loss ascrives to the surface diffusion. Different values of sticking coefficients on Si and on SiO2 surface greatly influenced the deopsited thin film profile. In addition, as the lateral wall angle decreased, the selectively deposited film had improved uniformity except the vicinity of trench wall. The optimum eondition for the most flat selective film deposition pattern is the case with low sticking coefficient and slightly increased surface diffusion coefficient.

• Fibers and Polymers
• /
• v.6 no.2
• /
• pp.108-112
• /
• 2005

Nanocomposite films were prepared by casting the solution of polyacrylonitrile (PAN) and single wall nanotube (SWNT) in nitric acid subsequent to sonication. Even though SWNT shows good dispersion visually, the reinforcing effect was not satisfactory. The G-band Raman spectra of the drawn film clearly demonstrated that SWNTs in the film are well-oriented along the drawing axis of the film. The electrical resistivity of the film prepared using nitric acid was lower than that of the film using DMF. Thus, nitric acid is presumably more effective in dispersing nanotubes than DMF.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.5
• /
• pp.628-636
• /
• 1997

Flow visualization technique incorporating photochromic dye is used to study the flow characteristics of the gravity driven laminar wavy film. The film thickness and wave speed are successfully measured by flow visualization. As the inclination angle increases, the waves have higher peaks and lower substrate thickness. The measured cross stream velocity at the free surface is up to 10% of stream wise velocity, which shows enhanced mixing in the lump of the film. The measured stream wise velocity profiles are close to parabolic profile near the substrate and the peak but show significant velocity defect near the rear side of the wave. The measured wall shear rate distributions show good agreement with the previous workers' numerical results.