• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.359-366
• /
• 2000

A numerical study has been performed for the 2-dimensional film cooling employed in the cooling of hot components such as gas turbines. The flow and heat transfer characteristics are numerically simulated using FLUENT software. Blowing ratios vary from 0.25 to 5.0 and coolant injection angles vary from $15^{\circ}\;to\;60^{\circ}\;in\;15^{\circ}$ increment. The result shows that, for all cases, there exists a blowing ratio which maximizes film cooling effect (measured by the distance from the slot exit to the downstream wall location at which temperature increases to 900 K) for a given injection angle. It is also observed that the film cooling effectiveness decreases when downstream wall is sunk or lifted. The simulation has been performed using both constant properties and temperature dependent variable properties. It is found that the cases with constant properties overestimate the film cooling effect considerably.

• Journal of Magnetics
• /
• 제15권4호
• /
• pp.169-172
• /
• 2010

The coercivity mechanism in permanent magnets was analyzed according to the effects of domain nucleation and domain wall pinning. The coercivity mechanism of a TbCo thin film with high perpendicular magnetic anisotropy was considered in terms of the local inhomogeneity in the thin film. The initial magnetization curves of the TbCo thin films demonstrated domain wall pinning to be the main contributor to the coercivity mechanism than domain nucleation. Based on the coercivity model proposed by Kronmuller et al., the inhomogeneity size acting as a domain wall pinning site was determined. Using the measured values of perpendicular anisotropy constant ($K_u$), saturation magnetization ($M_s$), and coercivity ($H_c$), the inhomogeneity size estimated in a TbCo thin film with high coercivity was approximately 9 nm.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.624-629
• /
• 2001

An experimental study was performed to investigate adiabatic wall temperature and heat transfer coefficient around on a module with longitudinal fin heat sink cooled by forced air flow. In the first method, inlet air flow(1-7m/s) and input power(3-5W) was varied after a heated module were placed on an adiabatic floor($320{\times}550{\times}1mm^{3}$). An adiabatic wall temperature was determinated to use liquid crystal film(LCF). In the second method to determinate heat transfer coefficient, inlet air flow(1-7m/s) and the heat flux of rubber heater($0.031-0.062\;W/cm^{2}$) was varied after an adiabatic module was placed on rubber heater covering up an adiabatic floor. In addition, surface oil-film visualization were performed to characterize the macroscopic flow-field around a module.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제24회 춘계학술대회논문집
• /
• pp.203-207
• /
• 2005

본 연구는 액체산소와 케로신을 추진제로 하는 액체로켓엔진에 막냉각 링을 장착하여 추진제의 혼합비의 변화 및 막냉각제의 종류, 유량 그리고 분사위치에 따라 추력실 길이방향으로 외벽온도를 측정하였다. 연소실험을 위하여 thin wall 연소실과 노즐을 제작하였으며, 측정된 온도를 이용하여 추력실에 발생하는 열유속을 계산하였다.

• International journal of advanced smart convergence
• /
• 제11권2호
• /
• pp.64-70
• /
• 2022

In recent years, with the continuous innovation and upgrading of engine software, the real-time rendering technology in film and television has been continuously improved, and the virtual production technology has also developed rapidly. This paper introduces the green screen often used in traditional film production and a virtual production technology based on light-emitting-diode background wall that was proposed and implemented last year. We analyzed the two production methods of virtual production and compared their characteristics. Based on these results, we can better understand the differences and respective advantages of the two production methods. And we also can according to the production budget, production cycle and the creative and technical capabilities of the team make better choices during the production process. We believe virtual production technology will be production in the future to provide a more solid technical guarantee for the development of the film industry, and this work will pave the way for further research on virtual production technology.

• Journal of Mechanical Science and Technology
• /
• 제16권3호
• /
• pp.376-385
• /
• 2002

Spray impingement and fuel film formation models with cavitation have been developed and incorporated into the computational fluid dynamics code, STAR-CD. The spray/wall interaction process was modeled by considering the effects of surface temperature conditions and fuel film formation. The behavior of fuel droplets after impingement was divided into rebound, spread and splash using the Weber number and parameter K(equation omitted). The spray impingement model accounts for mass conservation, energy conservation, and heat transfer to the impinging droplets. The fuel film formation model was developed by integrating the continuity, momentum, and energy equations along the direction of fuel film thickness. Zero dimensional cavitation model was adopted in order to consider the cavitation phenomena and to give reasonable initial conditions for spray injection. Numerical simulations of spray tip penetration, spray impingement patterns, and the mass of film-state fuel matched well with the experimental data. The spray impingement and fuel film formation models have been applied to study spray/wall impingement in high-speed direct injection diesel engines.

• 대한기계학회논문집B
• /
• 제21권1호
• /
• pp.140-152
• /
• 1997

A simultaneous measurement of the wall skin friction and near-wall streamwise velocity fluctuations is performed using hot film and hot wire anemometers to investigate the relation between them. Near-wall turbulence statistics measured with a hot-wire probe are in good agreement with previous results. Turbulence properties of the wall skin friction fluctuations measured with a hot film also show fairly good agreements with those measured by others except that rms level is lower in the present study. Long-time averaged space- time correlations show that the wall skin friction is highly correlated with a turbulence structure which is tilted from the wall in the streamwise direction. Tilting angles are obtained from the phase shifts between the wall skin-friction and streamwise velocity fluctuations. The convection velocity of the near-wall streamwise velocity obtained from the space-time correlation is in good agreement with that from the direct numerical simulation database.

• Carbon letters
• /
• 제14권4호
• /
• pp.255-258
• /
• 2013

Flexible transparent conducting films (TCFs) were fabricated by dip-coating single-wall carbon nanotubes (SWCNTs) onto a flexible polyethylene terephthalate (PET) film. The amount of coated SWCNTs was controlled simply by dipping number. Because the performance of SWCNT-based TCFs is influenced by both electrical conductance and optical transmittance, we evaluated the film performance by introducing a film property factor using both the number of interconnected SWCNT bundles at intersection points, and the coverage of SWCNTs on the PET substrate, in field emission scanning electron microscopic images. The microscopic film property factor was in an excellent agreement with the macroscopic one determined from electrical conductance and optical transmittance measurements, especially for a small number of dippings. Therefore, the most crucial factor governing the performance of the SWCNT-based TCFs is a SWCNT-network structure with a large number of intersection points for a minimum amount of deposited SWCNTs.

• 한국세라믹학회지
• /
• 제45권1호
• /
• pp.48-53
• /
• 2008

In order to reduce signal delay in ULSI, an intermetal material of low dielectric constant is required. Ordered mesoporous silica film is proper to intermetal dielectric due to its low dielectric constant and superior mechanical properties. The ordered mesoporous silica film prepared by TEOS (tetraethoxysilane) / MTES (methyltriethoxysilane) mixed silica precursor and Brij-76 surfactant was surface-modified by HMDS (hexamethyldisilazane) treatment to reduce its dielectric constant. HMDS can substitute $-Si(CH_3)_3$ groups for -OH groups on the surface of silica wall. In order to modify interior silica wall, HMDS was treated by two different processes except the conventional spin coating. One process is that film is dipped and stirred in HMDS/n-hexane solution, and the other process is that film is exposed to evaporated HMDS. Through the investigation with different HMDS treatment, it was concluded that surface modification in evaporated HMDS was more effective to modify interior silica wall of nano-sized pores.

• 치과방사선
• /
• 제27권2호
• /
• pp.49-61
• /
• 1997

The purpose of this study was to compare E-speed film, CDR, and modified CDR images by means of observing some artificial defects of alveolar bone wall in the sound human dried mandibles. High diagnostic accuracy was shown in 1 wall and 4 wall defects by all 5 observers (2 Radiologists, 2 Periodontists, 1 General practitioner), but the diagnosis in 2 wall and 3 wall defects was inaccurate. Modified CDR images had the more diagnostic accuracy than E-speed film and CDR images, but there was no statistical difference among them. Finally, radiologist used modified CDR images more than others and used equalization effect more than the change in contrast and/or brightness.