• 한국유체기계학회 논문집
• /
• 제4권4호
• /
• pp.37-42
• /
• 2001

In the present study, flow characteristics of turbulent oscillatory flow in an oscillator connected to square-sectional $180^{\circ}$ curved duct are investigated experimentally. In order to investigate wall shear stress and pressure distributions, the experimental studies for air flows we conducted in a square-sectional $180^{\circ}$ curved duct by using the LDV system with the data acquisitions and the processing system. The wall shear stress at bend angle of the $150^{\circ}$ and pressure distribution of the inlet (${\phi}=0^{\circ}$) to the outlet (${\phi}=180^{\circ}$) by $10^{\circ}$ intervals of the duct are measured. The results obtained from the experiment are summarized as follows : wall shear stress values in the inner wall we larger than those in an outer wall, except for the phase angle (${\omega}t/{\pi}/6$) of 3, because of the intensity of secondary flow. The pressure distributions are the largest in accelerating and decelerating regions at the bend angle(${\phi}$) of $90^{\circ}$ and pressure difference of inner and outer walls is the largest before and after the ${\phi}=90^{\circ}$.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2006년 창립20주년기념 정기학술대회 및 국제워크샵
• /
• pp.230-232
• /
• 2006

Failure behaviors of thin cylinder with corrosion are very important for the integrity of boiler and pressure vessel system. In this study, FEM with internal pressure are conducted on 1000 mm diameter (length 3000 mm and thickness, 5.9 mm) SS400 carbon steel. Failure behaviors of locally wall thinned cylinders were calculated by elasto-plastic analysis using finite element method. The elasto-plastic analysis was performed by FE code ANSYS. We simulated various types of local wall thinning that can be occurred at cylinder surface due to corrosion. Locally wall thinned shapes were machined to be different in size along the circumferential or axial direction of straight cylinder. In case of local wall thinned length 30 mm, internal pressure, when the crack initiation and the plastic collapse occur, didn't decrease dramatically even though local wall thinned depth was deep. In 400 mm, the more local wall thinned depth is deep, the more internal pressure decreased dramatically. In degraded materials, crack is easily initiation but plastic collapse was difficult.

• 한국분무공학회지
• /
• 제9권4호
• /
• pp.24-30
• /
• 2004

Feedwater flowing tube side of number 5 high pressure feedwatrr heaters was heated by extracting steam from high pressure turbine and draining water from moisture separators and number 6 high pressure feedwater heaters and supplied into steam generators. Because the extracting steam from the high pressure turbine is two phase fluid of high temperature, high pressure, and high speed and flows to inverse direction after impinging to impingement baffle. the shell wall of the number 5 high pressure feedwater heater may be affected by flow accelerated corrosion. On May 14, 1999, Point Beach Nuclear Plant (PBNP) with operating at full power experienced a steam leak from rupture of shell side of number 4B feedwater heater. Also, d domestic nuclear power plant experienced a severe wall thinning of shell side of number 5A and 5B feedwater heaters. This paper describes the fluid mixing analysis study using PHOENICS code in order to get at the root of the shell wall thinning of the feedwater heaters. The sections included in the fluid mixing analysis model are around the number 5h feedwater heater shell including the extracting pipeline. To identify the relation between the local velocities and wall thinning. the local velocities according to the analysis results were compared with the distribution of the shell wall thickness by ultrasonic test.

• 한국안전학회지
• /
• 제12권3호
• /
• pp.139-146
• /
• 1997

In this study, centrifugal model tests were performed to investigate the behavior of excavated earth retaining wall with the depth of excavation and different types of wall(aluminum, steel panel). Jumunjin standard sand was used for foundation soil. The raining method was adopted to form the required relative density of the model ground. The lateral earth pressure measured from tests were compared with estimated active earth pressure by Rankine's theory. The test results have shown that the earth pressure acting on the retaining wall and the rotation displacement of the wall are influenced by the depth of excavation and the type of wall. It was found from the test results that the deformation of the wall increases with the depth of excavation.

• 한국안전학회지
• /
• 제23권5호
• /
• pp.22-29
• /
• 2008

This paper provides the evaluation method for the pressure vessel with internal wall-thinning defect, which is based on ASME design criteria. Pressure vessel has wall-thinning partially and patch reinforcement has been attached for reliable operating. However, present partial wall thinning could be through wall thinning at the next inspection time with present corrosion progress speed. Therefore safety margin was calculated for various conditions from present wall-thinning condition to additive patch reinforced condition via two-dimensional and three-dimensional, geometrically linear FE analyses using elastic materials.

• Wind and Structures
• /
• 제30권3호
• /
• pp.219-229
• /
• 2020

Net pressures on roofs and walls of buildings are dependent on the internal and external pressure fluctuations. The variation of internal and external pressures are influenced by the size and location of the openings. The correlation of external and internal pressure influences the net pressures acting on cladding on different parts of the roof and walls. The peak internal and peak external pressures do not occur simultaneously, therefore, a reduction can be applied to the peak internal and external pressures to obtain a peak net pressure for cladding design. A 1:200 scale wind tunnel model study was conducted to determine the correlations of external and internal pressures and effective reduction to net pressures (i.e., net pressure factors, F_C) for roof and wall cladding. The results show that external and internal pressures on the windward roof and wall edges are well correlated. The largest ${\mathcal{C}}_{{\check{p},net}$, highest correlation coefficient and the highest F_C are obtained for different wind directions within 90° ≤ θ ≤ 135°, where the large openings are on the windward wall. The study also gives net pressure factors F_C for areas on the roof and wall cladding for nominally sealed buildings and the buildings with a large windward wall opening. These factors indicate that a 5% to 10% reduction to the action combination factor, K_C specified in AS/NZS 1170.2(2011) is possible for some critical design scenarios.

• 대한기계학회논문집A
• /
• 제30권5호
• /
• pp.568-575
• /
• 2006

The present paper provides plastic limit load solutions of axial and circumferential through-wall cracked pipes based on detailed three-dimensional (3-D) finite element (FE) limit analysis using elastic-perfectly-plastic behavior. As a loading condition, axial tension, global bending moment, internal pressure, combined tension and bending and combined internal pressure and bending are considered for circumferential through-wall cracked pipes, while only internal pressure is considered for axial through-wall cracked pipes. Especially, more emphasis is given for through-wall cracked pipes subject to combined loading. Comparisons with existing solutions show a large discrepancy in short through-wall crack (both axial and circumferential) for internal pressure. In the case of combined loading, the FE limit analyses results show thickness effect on limit load solutions. Furthermore, the plastic limit load solution for circumferential through-wall cracked pipes under bending is applied to derive plastic $\eta\;and\;{\gamma}$-factor of testing circumferential through-wall cracked pipes to estimate fracture toughness. Being based on detailed 3-D FE limit analysis, the present solutions are believed to be meaningful fur structural integrity assessment of through-wall cracked pipes.

• 대한기계학회논문집B
• /
• 제36권11호
• /
• pp.1055-1063
• /
• 2012

16채널 어레이 마이크로폰을 이용하여 난류 유동장 내 벽면 압력섭동에 대한 측정을 수행하였다. 본 실험에 사용된 코팅재질은 약 50 ppi (pores per inch)의 다공성 구조로 이루어진 우레탄 물질로 이루어져 있다. 코팅의 주된 목적은 난류 유동장 내 최소한의 공간을 유지하면서 대류속도로 진행하는 난류 와들을 필터링하는 역할을 하는 것이다. 평판 위 경계층의 측정은 열선 유속계를 이용하였으며 표면 마찰계수 값을 얻기위해 CPM법을 사용하였다. 벽압력 스펙트럼과 파수-주파수 스펙트럼 측정은 코팅에 의해 얼마나 에너지가 저감되는 지를 비교하기 위해 사용되었다. 벽면 코팅은 대류하는 무차원 벽면섭동압력에너지를 저감시켰지만, 컴플라이언트 코팅된 벽면 거칠기로 인해 일반 강체 평판에 비해 상대적으로 발달된 경계층을 형성하였으며 벽면 평균전단응력과 저주파수 압력스펙트럼 레벨도 함께 증가하였다.

• 한국지반공학회논문집
• /
• 제33권11호
• /
• pp.59-72
• /
• 2017

본 연구에서는 사질토 뒷채움재의 캔틸레버 옹벽에서 뒷굽 끝단 연직면에 작용하는 주동토압을 산정하는 방법을 제안하였다. 캔틸레버 옹벽에서 뒷굽길이에 따른 전단 영역의 변화는 벽체의 벽마찰력, 뒷채움 경사에 따라 뒷굽 끝단 연직면에 작용하는 주동토압에 영향을 준다. 뒷굽길이에 따라 변하는 파괴면각도를 가정하여 토압을 산정하는 한계평형법은 적용하기에 매우 복잡하므로 본 연구에서는 한계해석법을 사용하여 토압을 구하였다. 한계해석법으로 뒷굽길이에 따라 실제 파괴면각도가 고려된 토압을 정확히 산정하고, 이로부터 뒷굽 끝단 연직면에 작용하는 수평토압과 연직토압을 분석하였다. 본 연구결과에 의하면, 뒷굽길이가 짧아짐에 따라 내측 파괴면 경사각은 이론식보다 증가한 반면에 외측 파괴면 경사각은 영향을 받지 않았다. 뒷굽 끝단의 연직면에 작용하는 배면마찰각은 지표면 경사각과 벽면마찰각 사이의 값을 나타내었으며, 주동토압 또한 감소하였다. 최종적으로 상대적인 뒷굽길이와 뒷굽 끝단의 연직면에 작용하는 마찰각(연직토압/수평토압의 비)의 상관관계를 사용함으로써 Coulomb 토압을 간편하게 산정할 수 있도록 하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 지반공학 공동 학술발표회
• /
• pp.84-91
• /
• 2005

In case of soil nailing system, there have been many attempts to expand into slope and temporary earth retaining system stabilization method since the first ground excavation earth retaining system construction in 1993. Recently, jointing wall, underground wall of buildings and excavation earth retaining wall, construction were increasingly applied for effective utilization of the limited underground space and land application maximized. However, the application of joining wall into retaining wall or building by temporary soil nailing system and design of permanent wall were performed by using Rankine earth pressure theory without considering the distribution of earth pressure in the soil nailing. In this study was performed to introduce the design case by 'Two-Body Translation mechanism (TBTM)' to be able to consider distribution of earth pressure in the soil nailing when designing the permanent jointing wall using soil nailing system for effective utilization of ground space. Also, this study attempts to evaluate the earth pressure change, decreasing effect of wall displacement and increasing effect of stability when advanced soil nailing system is constructed using $FLAC^{2D}$ ${\nu}er.$ 3.30 program and 'Two-Body Translation mechanism'.