• 대한기계학회논문집B
• /
• 제37권9호
• /
• pp.799-805
• /
• 2013

본 논문에서는 나노유체를 사용한 평판형 집열기의 효율을 예측하기 위한 이론적인 연구를 수행하였다. 평판형 태양열 집열기 내부의 온도분포에 관한 해석적 해를 구하기 위해 무차원화된 2 차원 열 확산방정식을 풀었으며, 이 과정에서 흡광계수와 복사강도는 파장에 독립적이라고 가정하였다. 이렇게 주어진 식을 바탕으로, 물-기반 단일벽 탄소나노혼 나노유체를 작동유체로 사용할 경우 나노입자의 부피비, 열손실의 크기, 집열기의 높이에 따른 무차원 온도분포를 파악해 보았다. 마지막으로 나노유체 기반 평판형 집열기의 효율을 예측해 본 결과 일정 형상조건 이내에서 나노유체 태양열 집열기가 기존 집열기 보다 높은 효율을 가질 수 있음을 파악하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.1
• /
• pp.361-365
• /
• 2003

Planar Inductively Coupled Plasma (PICP) etching of InGaP was performed in $BCl_3,\;BCl_3/Ar\;and\;BCl_3/Ne$ plasmas as a function of ICP source power ($0\;{\sim}\;500\;W$), RIE chuck power ($0\;{\sim}\;150\;W$), chamber pressure ($5\;{\sim}\;15\;mTorr$) and gas composition of $BCl_3/Ar\;and\;BCl_3/Ne$. Total gas flow was fixed at 20 sccm (standard cubic centimeter per minute). Increase of ICP source power and RIE chuck power raised etch rate of InGaP, while that of chamber pressure reduced etch rate. We also found that some addition of Ar and Ne in $BCl_3$ plasma improved etch rate of InGaP. InGaP etch rate was varied from $1580\;{\AA}/min$ with pure $BC_3\;to\;2800\;{\AA}/min$ and $4700\;{\AA}/min$ with 25 % Ar and Ne addition, respectively. Other process conditions were fixed at 300 W ICP source power, 100 W RIE chuck power and 7.5 mTorr chamber pressure. SEM (scanning electron microscopy) and AFM (atomic force microscopy) data showed vertical side wall and smooth surface of InGaP at the same condition. Proper addition of noble gases Ar and Ne (less than about 50 %) in $BCl_3$ inductively coupled plasma have resulted in not only increase of etch rate but also minimum preferential loss and smooth surface morphology by ion-assisted effect.

• 한국유체기계학회 논문집
• /
• 제8권4호
• /
• pp.39-47
• /
• 2005

The present study has been performed to investigate the influences of rectangular fins on heat transfer in an impingement/effusion cooling system with crossflow. To simulate the impingement/effusion cooling system with initial crossflow, two perforated plates are placed in parallel and staggered arrangements with a gap distance of 2 times of the hole diameter. The crossflow passes between the plates, and various rectangular fins are installed on the plates. Reynolds number based on the hole diameter is fixed to 10,000 and the flow rate of crossflow is changed from 0.5 to 1.5 times of that of the impinging jet. A naphthalene sublimation method is used to obtain the heat/mass transfer coefficients on the effusion plate. Also to analyze the flow characteristics, a numerical calculation is performed. When rectangular fins are installed, the flow and heat transfer pattern is changed greatly from the case without fins. In the injection hole region, the jet impinges on effusion plate without deflection and wall jet spreads symmetrically. In the effusion region, the crossflow accelerates due to the decrease of cross-sectional area in the channel. Local heat/mass transfer coefficients are enhanced significantly compared to the case without fins. As the blowing ratio increases, the effect of rectangular fins against the crossflow becomes more significant and then the higher average heat/mass transfer coefficients are obtained than the case without fins. However, the increase of blockage effect gives more pressure loss in the channel.

• 한국임상수의학회지
• /
• 제23권2호
• /
• pp.197-201
• /
• 2006

A 2-year-old female mongrel dog was referred to the Veterinary Medical Center of Chungbuk National University due to anorexia, depression and weight loss after the administration of exogenous estrogen for contraception in the local hospital. Although the dog was medicated with antibiotics and fluid for two weeks in the local hospital, there was a deterioration in the patient's general condition. Therefore the dog was referred to our Veterinary Medical Center. Hematological and biochemical analysis showed non-regenerative anemia, thrombocytopenia, severely immature leukocytosis, hyperbilirubinemia, hyperglycemia and elevated serum alkaline phosphatase, gamma-glutamyltransferase, and lactate dehydrogenase. Abdominal ultrasonography showed double line of gallbladder and irregular hypertrophic wall of uterus. On the basis of these examination's results and history taking, final diagnosis was exogenous estrogen-induced myelotoxicosis with cholecystitis and endometritis. The symptomatic therapy for estrogen toxicosis was performed for 26 days after the final diagnosis. However, the symptom had no response to therapy except endometritis and anemia. On day 135 after administration of estrogen, platelet and neutrophil count were normalized, but monocytic leukocytosis was occurred.

• 한국정밀공학회지
• /
• 제23권2호
• /
• pp.199-206
• /
• 2006

Automatic grease lubricator is equipment that provides adequate amount of fresh grease constantly to the shaft and the bearings of machines. It minimizes the friction heat and reduces the friction loss of machines to the least. This research is to develop automatic grease lubricator by gear driven mechanism with controlled operation time. The ultimate design of this equipment is to lubricate an adequate amount of grease by a simple switch clicking according to the advanced set cycle. The backlash of the gear was minimized to increase the output power. To increase the power of gear mechanism, the binding frequency and the thickness of the coil were changed. To control the rotating cycles of the main shaft according to its set numbers, different resistance and chips were used to design the circuit to controls electrical signals with pulse. The body of the lubricator was analyzed by stress analysis with different constructed angle. The stress analysis for differing loading pressures applied to the exterior body of grease lubricator due to the setup angle, was found that the maximum stress was distributed over the outlet part where the grease lubricator suddenly narrowed contracts. Digital mock-up was analyzed and the rapid prototyping(RP) trial products were tested with PCB circuit and grease. The evaluation of the outlet capacity for RP trial products was conducted, because the friction caused by the outlet on the wall surface was an important factor in the operation of the equipment. Finally, the finishing process was applied to decrease the roughness of the surface to a comparable level and was able to test the performance examination for the product.

• Journal of Chest Surgery
• /
• 제38권7호
• /
• pp.514-517
• /
• 2005

위장관 간질 종양은 위장관 전역에서 발생하며 그 중 위와 소장 등에 많이 생기며 식도에서도 발생한다. 44세 남성이 연하곤란과 체중감소를 주소로 내원하여 시행한 상부 위장관 내시경 검사 및 흉부 전산화 단층 촬영에서 식도 하부의 완전폐쇄, 위의 전방 편위 소견과 중앙부 괴사를 동반하는 최대 직경 15cm 정도의 저음영의 거대 종괴를 보여 흉복부 절개를 이용하여 하부 식도 및 위전적출술을 시행하였다 종양은 CDl17 (c-kit)와 CD34에서 양성을 보여 악성 위장관 간질 종양으로 확진되었으며 현재 외래 추적관찰 중이다.

• 한국해양학회지:바다
• /
• 제5권2호
• /
• pp.77-85
• /
• 2000

회전반 유체실험을 이용하여 국지적 외력에 의한 순환특성을 모의하는 방법을 고찰하였다. 기존의 실험들은 균일한 외력에 의한 순환특성을 고려하였으나 한국 동해를 고려할 때 바람응력 컬의 남북 방향으로의 분포특성 및 해수면 열 손실의 북부해역에서의 존재를 근거로 공간적인 국지성 및 계절 변화를 염두에 둔 주기성을 복합적으로 모의할 수 있는 방법과 실험을 실시하였다. 바람응력 컬의 국지성은 에크만 층내 압력 경도력을 발생시켜 내부에도 같은 압력 경도력이 전달되어 지형류가 발생되게 하였으며 해수면 냉각을 위해서는 용기의 측면을 국지적으로 냉각시켜 자유표면을 유지할 수 있는 방법을 제시하였다. 남북에 위치한 두 개의 서로 다른 방향을 갖는 폐쇄순환과 서안경계류의 크기 및 이안 위치 변화등을 냉각효과 첨부시 및 응력 컬의 주기성을 갖는 경우를 택하여 실험적으로 관찰하였다.

• 센서학회지
• /
• 제9권5호
• /
• pp.334-340
• /
• 2000

본 논문에서는 패러데이의 전자기 유도 법칙을 응용한 마이크로 전자 유량 센서를 제작하였다. 마이크로전자 유량 센서는 열 발생이 없고 빠른 응답 속도를 가지고 있고 압력 손실이 없는 장점을 가지고 있다. 전도성 유체가 영구 자석 자장 내의 유로를 통과할 때, 유속에 비례하는 유도 기 전력이 발생하게 되는데, 발생된 기 전력은 유로 벽에 제작된 전극으로 검출된다. 마이크로 전자 유량 센서는 유로를 가지고 있는 두 장의 실리콘 웨이퍼 기판과 전극, 그리고 두 개의 영구 자석으로 구성되어 있다. 두 장의 실리콘 웨이퍼 기판을 이방성 식각 공정으로 유로를 제작하고, Cr/Au를 증착하여 전극을 제작한다. 제작된 마이크로 전자 유량 센서에 유량을 변화시킬 때, 발생되는 기 전력을 측정한다.

• Journal of Gastric Cancer
• /
• 제15권4호
• /
• pp.278-285
• /
• 2015

Purpose: Gastric submucosal tumors (SMTs) located very close to the esophagogastric junction (EGJ) are a challenge for gastric surgeons. Therefore, this study reports on the experience of using endoscopic and laparoscopic full-thickness resection (ELFR) with laparoscopic two-layer suturing in such tumors. Materials and Methods: Six patients with gastric SMTs very close to the EGJ underwent ELFR with laparoscopic two-layer suturing at Kyungpook National University Medical Center. With the patient under general anesthesia, the lesser curvature and posterior aspect adjacent to the EGJ were meticulously dissected and visualized using a laparoscopic approach. A partially circumferential full-thickness incision at the distal margin of the tumor was then made using an endoscopic approach under laparoscopic guidance. The SMT was resected using laparoscopic ultrasonic shears, and the gastric wall was closed using two-layer suturing. Thereafter, the patency and any leakage were checked through endoscopy. Results: All the ELFR procedures with laparoscopic two-layer suturing were performed successfully without an open conversion. The mean operation time was $139.2{\pm}30.9$ minutes and the blood loss was too minimal to be measured. The tumors from four patients were leiomyomas, while the tumors from the other two patients were gastrointestinal stromal tumors with clear resection margins. All the patients started oral intake on the third postoperative day. There was no morbidity or mortality. The mean hospital stay was $7.7{\pm}0.8$ days. Conclusions: ELFR with laparoscopic two-layer suturing is a safe treatment option for patients with an SMT close to the EGJ, as major resection of the stomach is avoided.

• 한국태양에너지학회 논문집
• /
• 제35권4호
• /
• pp.1-7
• /
• 2015

The operation of the natural circulation type solar heating systems with facade integrated collector was analyzed by experiment. Two different types of flat plate solar collectors were used for these experiments. One was for the normal flat plate solar collector with the size of 1m*2m and the other was for the large size solar collector with $4m^2$(1m*4m). The experiments were carried out to investigate the effect of the series or parallel connection method on the performance of the collectors. As a result, the solar thermal system which is installed on the wall or facade would be applicable for the natural circulation type if the system design reflects various parameters, including collector connecting method(series or parallel), to provide enough vertical height between collector and storage tank, and to reduce pressure loss due to collector and piping network, etc. The natural circulation type of solar thermal system as proposed in this study can increase the system reliability by removing or minimizing the use of the components such as pump, controller, sensors which may cause serious troubles of the system for a long-time operation