The KSFM Journal of Fluid Machinery (한국유체기계학회 논문집)

Korean Society for Fluid machinery (한국유체기계학회)
권호 표지
DOI QR코드

DOI QR Code

Heat/Mass Transfer Characteristics in Impingement/Effusion Cooling System with Rectangular Fins for Combustor Liner Cooling

가스터빈 연소실 냉각을 위한 충돌제트/유출냉각기법에서 사각핀 설치에 따른 열/물질전달 특성

  • Published : 2005.08.01
Download PDF
⟨ Previous Next ⟩

Abstract

The present study has been performed to investigate the influences of rectangular fins on heat transfer in an impingement/effusion cooling system with crossflow. To simulate the impingement/effusion cooling system with initial crossflow, two perforated plates are placed in parallel and staggered arrangements with a gap distance of 2 times of the hole diameter. The crossflow passes between the plates, and various rectangular fins are installed on the plates. Reynolds number based on the hole diameter is fixed to 10,000 and the flow rate of crossflow is changed from 0.5 to 1.5 times of that of the impinging jet. A naphthalene sublimation method is used to obtain the heat/mass transfer coefficients on the effusion plate. Also to analyze the flow characteristics, a numerical calculation is performed. When rectangular fins are installed, the flow and heat transfer pattern is changed greatly from the case without fins. In the injection hole region, the jet impinges on effusion plate without deflection and wall jet spreads symmetrically. In the effusion region, the crossflow accelerates due to the decrease of cross-sectional area in the channel. Local heat/mass transfer coefficients are enhanced significantly compared to the case without fins. As the blowing ratio increases, the effect of rectangular fins against the crossflow becomes more significant and then the higher average heat/mass transfer coefficients are obtained than the case without fins. However, the increase of blockage effect gives more pressure loss in the channel.

Keywords

References

  1. HoIlwarth, B. R. and Dagan, L., 1980, 'Arrays of Impinging Jets with Spent Fluid Removal through Vent Holes on the Target Surface Part 1: Average Heat Transfer,' Journal of Engineering for Power, Vol. 102, pp. 994-999 https://doi.org/10.1115/1.3230372
  2. HoIlwarth, B. R, Lehmann, G. and Rosiczkowski, J., 1983, 'Arrays of Impinging Jets with Spent Fluid Removal through Vent Holes on the Target Surface Part 2: Local Heat Transfer,' Journal of Engineering for Power, Vol. 105, pp. 393-402 https://doi.org/10.1115/1.3227428
  3. Cho, H. H. and Goldstein, R. J., 1996, 'ÁEffect of Hole Arrangements on Impingement/ Effusion Cooling,' Proceeding of the 3rd KSME-JSME Thermal Engineering Conference, pp. 71-76
  4. Cho, H. H. and Rhee, D. H., 2001, 'Local Heat/Mass Transfer Measurement on the Effusion Plate in Impingement/Effusion Cooling System,' Journal of Turbomachinery, Vol. 123, pp. 601-608 https://doi.org/10.1115/1.1344904
  5. Cho, H. H., Choi, J. H. and Rhee, D. H. 2001, 'The Effects of Hole Arrangements on Heat/Mass Transfer of Impingement/Effusion Cooling System,' Proceedings of ExHFT-5, pp. 975-980
  6. Metzger, D. E. and Korstad, R. J., 1992, 'Effect s of Cross flow in Impingement Heat Transfer,' Journal of Engineer-ing for Power, Vol. 94 , pp. 35-41
  7. Florschuetz, L. W., Metzger, D. E. and Su, C. C., 1984, 'Heat Transfer Characteristics for Jet Array Impingement With Initial Crossflow,' Journal of Heat Transfer, Vol. 106, pp. 34-41 https://doi.org/10.1115/1.3246656
  8. Haiping, C., Wanbing, C. and Taiping, H., 1999, '3-D Numerical Simulation of Impinging Jet Cooling with Initial Crossflow,' ASME Paper No. 99-GT-256
  9. Rhee, D. H., Nam, Y. W. and Cho, H. H., 2004, 'Local Heat/Mass Transfer with Various Rib Arrangement in Impingement/Effusion Cooling System,' ASME Paper No. GT2004-53686
  10. 홍성국, 이동호, 조형희, 2004, '충돌제트/유출냉각기법에서 핀-훤 설치에 따른 냉각특성에 대한 연구,' 제3회 한국유체공학 학술대회, pp. 663-666
  11. Ambrose, D., Lawrenson, I. J. and Sparke, C. H. S., 1975, 'The Vapor Pressure of Naphthalene,' Journal of Chemical Thermodynamics, Vol. 7, pp. 1173-1176 https://doi.org/10.1016/0021-9614(75)90038-5
  12. Goldstein, R. J. and Cho, H. H., 1995, 'A Review of Mass Transfer Mea surement Using Naphthalene Sublimation,' Experimental Thermal and Fluid Science, Vol. 10, pp. 416-434 https://doi.org/10.1016/0894-1777(94)00071-F
  13. Kline, S. J. and McClintock, F. A., 1953, 'Describing Uncertainty in Single-Sample Experiments,' Mechanical Engineering, Vol. 75 , pp. 3-8