• Selected Papers of The Society of Naval Architects of Korea
• /
• v.1 no.1
• /
• pp.76-90
• /
• 1993

A new propeller series is developed using the newly developed blade section (KH 18 section) which has better cavitation characteristics and higher lift-drag ratio at wade angle-of-attack range than a conventional section. The radial patch distribution of the new series propellers is variable stance they were designed adaptively to a typical wake distribution. Basic geometric particulars of the series propellers. such as chord length, thickness, skew and rake distributions, are determined on the basis of recent full scale propeller geometric data. The series is developed for propellers having 4 blades, and blade area ratios of 0.3, 0.45, 0.6 and 0.75. Mean pitch ratios are varied as 0.5, 0.6, 0.7, 0.95 and 1.1 for each blade area ratio. The new propeller series consists of 20 propellers and is named as the KD(KRISO-DAEWOO)-propeller series. Propeller open-water tests are performed at the towing tank, and cavitation observation tests and fluctuating pressure tests are carried out at the cavitation tunnel of KRISO. $B_{p}-\delta$ curves, which can be used to select the optimum propeller diameter at the preliminary design stage, are derived from a regression analysis of the propeller open-water test results. The KD-cavitation chart is derived from the cavitation observation test results by choosing the local maximum lift coefficient and the local cavitation number as parameters. The cavity extent predicted by the KD-cavitation chart would be more accurate compared to that by an existing cavitation charts, such as the Burrll's cavitation chart, since the former is derived from the cavitation observation test results in a typical ship's wake, while the lather is derived from the test results in a uniform flow.

• Plant Journal
• /
• v.12 no.3
• /
• pp.24-31
• /
• 2016

Wind-induced vibration is a phenomenon that a struture is oscillated due to wind force such as buffeting, vortex shedding wake and etc., which is one of important characteristics to be considered for design in case that stack has significant slenderness ratio or low natural frequency. International design standards of stack define several criteria for evaluating the suitability of stack design, which describe the required design considerations for each range of design parameters and provide the instruction to verify the stack design against wind-induced vibration simply. However, there is a limitation that they cannot provide quantitative information in case code requirement cannot be satisfied due to constraints of plant space or economical design. In order to overcome the limiation of code, integrated numerical analysis of computational fluid dynamics, harmonic analysis and finite element analysis were proposed to investigate wind-induced vibration for multiple stacks in actual plant. Simulated results of mutual wake interference effect between adjacent stacks were evaluated and compared to the criteria in international standards.

• Journal of Navigation and Port Research
• /
• v.35 no.10
• /
• pp.805-810
• /
• 2011

An experiment was carried out to figure out the instantaneous flow characteristics in the wake of the transom stern's 2-dimensional section by 2-frame grey level cross correlation PIV method at $Re=3.5{\times}103$, $Re=7.0{\times}103$. The stern angles of models were learning at $45^{\circ}$(Model "A"), $90^{\circ}$(Model "B") and $135^{\circ}$(Model "C") respectively based on the survey results of real ships. The depth of wetted surface is 40mm from free surface. As Reynolds number increases, vortices increase in volume and move their way to the downstream. Flow separation appeared at the end of model's bottom.

• Journal of Ocean Engineering and Technology
• /
• v.33 no.2
• /
• pp.123-130
• /
• 2019

The flow around a curved riser exposed to the current in various directions was investigated at a Reynolds number of 100 using a numerical simulation. The present study found that the flow features of the curved riser were distinct from those of a straight riser as a result of its large radius of curvature. Namely, there were various wake patterns according to the flow's incident angle. As the incident angle increased from $0^{\circ}$ to $90^{\circ}$, a two-row street of vortices that developed along the centerline of the curved riser became more apparent. However, when the incident angle approached $180^{\circ}$ from $90^{\circ}$, these vortices were completely suppressed by the interaction between the wake and an axial flow induced by the curvature of the riser. To identify this feature, the sectional force coefficients were also considered, and it was found that the force coefficients could be different from those found in a sectional analysis based on the strip theory when investigating vortex-induced vibration. As a result, this kind of study would be important to realistically estimate the riser VIV (vortex-induced vibration) and fatigue life, and a new force coefficient database that includes the three-dimensional effect should be established.

• Journal of computational fluids engineering
• /
• v.13 no.1
• /
• pp.57-62
• /
• 2008

Laminar flows over a cube and a cuboid (cube extended in the streamwise direction) are numerically investigated for the Reynolds numbers between 50 and 350. First, vortical structures behind a cube and lift characteristics are scrutinized in order to understand the variation in vortex shedding characteristics with respect to the Reynolds number. As the Reynolds number increases, the flow over a cube experiences the steady planar-symmetric, unsteady planar-symmetric, and unsteady asymmetric flows. Similar to the sphere wake, the planar-symmetric flow over a cube can be divided into two different regimes: single-frequency regime and multiple-frequency regime. The former has a single frequency due to regular shedding of vortices with the same strength in time, while the latter has multiple frequency components due to temporal variation in the strength of shed vortices. Second, the effect of the length-to-height ratio of the cuboid on the flow characteristics is investigated for the Reynolds number of 270, at which planar-symmetric vortex shedding takes place behind a cube. With the ratio smaller than one, the flow over the cuboid becomes unsteady asymmetric flow, whereas it becomes steady flow for the ratios greater than one. With increasing the ratio, the drag coefficient first decreases and then increases. This feature is related to the flow reattachment on the side faces of the cuboid.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.158-163
• /
• 2005

In this paper the aeroacoustic characteristics of a tilt-rotor system is measured by using a sealed model tilt-rotor. With a microphone array system and the do-dopplerization algorithm, the location and the characteristics of rotor noise are successfully measured. The most of high frequency noise (4kHz) is found to be located at rotor blade tips, but the low frequency tonal noise is dominant on the middle of the rotor blades. The measured tonal noise characteristics are compared to the results of theoretical calculation. At 0.5m distance from the rotor plane, measured and calculated data are relatively well matched regardless of rotating speed and collective pitch angie for the azimuthal angles between $0^{\circ}\;and\;60^{\circ}$. However, the data on the azimuthal angles between $70^{\circ}\;and\;90^{\circ}$ are not quite comparable. In addition, the compared data for far-field case (1.5m) are quite different. This is probably due to the unsteady effect which if not included in the theoretical calculation.

• Journal of computational fluids engineering
• /
• v.6 no.3
• /
• pp.41-50
• /
• 2001

Effects of rotor-stator blade count ratio on the unsteady aerodynamic characteristics of a cascade was studied by using a Navier-Stokes code. Present Navier-Stokes code is a parallel code and works on a multi-cpu machine. It is based on the SIMPLE algorithm and uses QUICK scheme for convection terms and second order back difference for all temporal derivatives. Computations were carried out for two cases : case 1 is for 3 stator cascade passages subjected to two upstream wakes while case 2 is for 2 stator cascade passages subjected to three upstream wakes. Numerical solutions show that rotor-stator blade count ratio plays a significant role in the unsteady aerodynamic characteristics of the stator cascade. Case 2 shows smaller unsteady fluctuation than case 1, even if they show the same time averaged value. The smaller fluctuation of case 2 is believed due to strong interaction between unsteady vortices. The unsteady lift variation of case 2 is shown to have many high frequency fluctuations as more unsteady vortices travel around the cascade. The unsteady turbulent kinetic energy due to the upstream wake is also shown to decay faster through the cascade passage than in the free stream.

• Journal of the Society of Naval Architects of Korea
• /
• v.55 no.1
• /
• pp.75-82
• /
• 2018

Wedge-shaped fins are generally used to provide sufficient forces and moments to control and maneuver a supercavitating vehicle. There are four fins placed along the girth of the vehicle, near he tail: two of the fins are horizontal and the other two fins are vertical. In a fully developed supercavitating flow condition, a part of the fin is in a cavity pocket and the other is exposed to water. In this paper, experimental investigations of hydrodynamic characteristics of the wedge-shaped fin models are presented. Experiments were conducted at a cavitation tunnel of the Chungnam National University. We first closely observed the typical formation of wake cavitation and measured lift and drag forces acting on two different test models. Next, using a special device for generating natural and artificial supercavities, we investigated hydrodynamic forces at different cavitation number conditions. This work provides a basis for interpreting the cavity stability and hydrodynamic characteristics of the wedge-shaped control fin for a supercavitating vehicle.

• Wind and Structures
• /
• v.26 no.2
• /
• pp.89-98
• /
• 2018

For most full-scale tall buildings the Reynolds number of a flow field around a circular cylinder under strong wind is usually greater than $2{\times}10^7$, which is difficult to achieve in most wind tunnel tests. To explore the wind characteristics of tall cylindrical buildings with equidirectional grooves from subcritical to transcritical flow ($6.6{\times}10^4{\leq}Re{\leq}3.3{\times}10^5$ and $9.9{\times}10^6{\leq}Re{\leq}7.2{\times}10^7$), wind tunnel tests and full-scale large eddy simulations were carried out. The results showed that the rectangular-grooves narrow the wake width due to the downstream movement of the separation point and the deeper grooves cause smaller mean and fluctuating pressure while the peak pressure is little affected. Furthermore, the grooves lead to lower frequency of vortex shedding but the Strouhal number remains at the range from 0.15 to 0.35. The drag coefficient of the cylinders with grooves was found to be 2~3 times as large as that of smooth cylinders.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.7
• /
• pp.11-19
• /
• 2002

Inflating characteristics of the parachute canopies have been experimentally investigated with the objective of measuring the parachute opening parameters such as canopy filling time and the peak opening force using scaled parachute models. A device has been made and tested to eject a model parachute into a wind tunnel flow and to measure the drag force acting on it. The force-time histories and the peak opening force are obtained, and these comparative aerodynamic characteristics were analyzed and discussed, including the effect of forebody wake. The opening of the ringslot parachute model appeared to be faster than that of the available similar data by about 10~40%, and fair to good agreement was obtained for the reefed ribbon parachute.