• 인터넷정보학회논문지
• /
• 제18권6호
• /
• pp.15-23
• /
• 2017

Wireless power transmission (WPT) for wireless charging is currently attracting much attention as a promising approach to miniaturize batteries and increase the maximum total range of an electric vehicle. The main advantage of the laser power beam (LPB) approach is its high power transmission efficiency (PTE) over long distance. In this paper, we present the design of a laser power beam based WPT system, which has a best WPT channel selection technique at the receiver end when multiple power transmitters and single power receiver are operated simultaneously. The transmitters send their transmission channel information via optically modulated laser pulses. The receiver uses the received signal strength indicator and digitized data to choose an optimum power transmission path. We modeled a vertical multi-junction photovoltaic cell array, and conducted an experiment and simulation to test the feasibility of this system. From the experimental result, the standard deviation between the mathematical model and the measured values of normalized energy distribution is 0.0052. The error between the mathematical model and measured values are acceptable, thus the validity of the model is verified.

• Journal of electromagnetic engineering and science
• /
• 제10권4호
• /
• pp.219-223
• /
• 2010

Based on a provided closed-form wireless power transmission (WPT) efficiency formula, which may be used for any value of load, we have analyzed the WPT efficiencies between two metamaterial-inspired loop antennas in various aspects. Due to the modeling based on low frequency circuit theory, the provided formula at the center resonant frequency has been found to be accurate until when the distance between the two loop antennas increases to 15 cm (about $\lambda_0/6$ at 300 MHz). When the two loops get closer, the resonant frequency has been found to split into two in theory, simulations, and measurements. The EM-simulated and measured efficiencies at new resonant frequencies are 60.9 % and 46.3 %, respectively, at d=15 cm. With two extra rings around the loops, the maximum efficiency is enhanced to 93.7 % at d=15 cm. The effect of the additional two rings is about 30 %.

• 한국항행학회논문지
• /
• 제27권1호
• /
• pp.63-70
• /
• 2023

본 연구는 선박 추진 축계의 무선 센서 시스템(WSS) 응용을 위한 용량성 무선 전력 전송(C-WPT) 시스템을 제시한다. 커플링 커패시터 양쪽의 단일 Q 팩터 및 회로에서 무효 전력제거를 위해 양면 LCLC 컨버터 및 변압기 토폴로지가샤프트에서 WSS용 회전식 C-WPT 시스템을 구동하도록 설계되었습니다. 170pF의 용량을 갖는 병렬 연결된 평행판 회전 커패시터가 설회전축의 C-WPT 시스템용으로 설계 및 구현된다. 실험 결과 C-WPT 시스템은 3mm 거리 및 1 MHz 작동 주파수에서 7.8 W 출력 전력으로 66.67 %의 전송 효율을 달성했다. 따라서 제작된 C-WPT 시스템은 회전축의 WSS에 전원을 공급할 수 있음을 증명하였다.

• 전기학회논문지
• /
• 제63권6호
• /
• pp.776-779
• /
• 2014

In this paper, we analyzed the efficiency of magnetic resonance wireless power transmission (WPT) using superconductor coil according to the changing position of transmission and receiving coils. We implemented a WPT system using a magnetic resonance at a frequency of 63.1 kHz. Transmission and receiving coils using superconductor coil were wound on a spiral manner of diameter 100mm. For comparison, transmission and receiving coils using normal conductor coil were designed under the same condition. At a distance of 50mm, we measured efficiency when transmission-receiving coils were matched 25%, 50%, 75% and 100%. When a superconductor coil was applied to the transmission and receiving units, efficiency of WPT was very high. In addition, in the case of the superconducting transmission-receiving coils, when coils matched 100% the efficiency was 30% and matched 25% the efficiency was 8%.

• 전기전자학회논문지
• /
• 제17권3호
• /
• pp.317-323
• /
• 2013

본 논문에서는 자기공명 방식을 이용한 25W급 무선전력 전송 시스템을 설계 및 구현하는 것을 제안하고 있다. 본 논문에서 제안하는 자기공명 방식 무선전력 전송 시스템은 100W급 Class-F 송신기, 1.7MHz대역의 송수신 공진기, 40W급 Full-bridge 다이오드 수신기로 구성되어 있다. 특히 제안된 시스템은 수신기에 전달되는 전력이 부하를 구동할 수 있는 적정레벨로 유지될 수 있도록 송신기와 수신기 사이의 통신을 이용한 송신전력제어 기능을 구현하여 송신기가 최적의 전력을 송신하여 불필요한 전력 낭비를 줄일 수 있도록 구현되었다. 본 논문에서 제안된 시스템 및 송신전력 제어기능을 기반으로 다양한 기기에 동일한 기능의 적용이 가능하며 상용화에 보다 근접할 수 있을 것이다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2016년도 전력전자학술대회 논문집
• /
• pp.349-350
• /
• 2016

In the magnetically coupled wireless power transmit (WPT), the study of the multi-dimensional transmission coil to solve the low power transmission efficiency from the location of transmit coil and receiving coil is being developed. This paper, an important step in this study, presents the magnetically coupled model of the WPT system consist of the two-dimensional transmit coil and verifies by the simulation and experiment. The induced model in this paper can be used to design the WPT circuit and controller for the maximum transmission efficiency.

• 한국초전도ㆍ저온공학회논문지
• /
• 제18권1호
• /
• pp.46-49
• /
• 2016

The wireless power transfer (WPT) system using a magnetic resonance was based on magnetic resonance coupling of the transmission and the receiver coils. In these system, it is important to maintain a high quality-factor (Q-factor) to increase the transmission efficiency of WPT system. Our research team used a superconducting coil to increase the Q-factor of the magnetic resonance coil in WPT system. When the superconductor is applied in these system, we confirmed that transmission efficiency of WPT system was higher than normal conductor coil through a preceding study. The efficiency of the transmission and the receiver coil is affected by the magnetic shielding effect of materials around the coils. The magnetic shielding effect is dependent on the type, thickness, frequency, distance, shape of materials. Therefore, it is necessary to study the WPT system on the basis of these conditions. In this paper, the magnetic shield properties of the cooling system were analyzed using the High-Frequency Structure Simulation (HFSS, Ansys) program. We have used the shielding materials such as plastic, aluminum and iron, etc. As a result, when we applied the fiber reinforced polymer (FRP), the transmission efficiency of WPT was not affected because electromagnetic waves went through the FRP. On the other hand, in case of a iron and aluminum, transmission efficiency was decreased because of their electromagnetic shielding effect. Based on these results, the research to improve the transmission efficiency and reliability of WPT system is continuously necessary.

• 한국기계가공학회지
• /
• 제19권8호
• /
• pp.73-80
• /
• 2020

The 3D printing of electronics has been a major application topics in additive manufacturing technology for a decade. In this paper, wireless power transfer (WPT) technology for 3D electronics is studied to supply electric power to its inner circuit. The principle of WPT is that electric power is induced at the recipient antenna coil under an alternating magnetic field. Importantly, the efficiency of WPT does rely on the design of the antenna coil shape. In 3D printed electronics, a flat antenna that can be placed on the printed plane within a layer of a 3D printed part is used, but provided a different antenna response compared to that of a conventional PCB antenna for NFC. This paper investigates the WPT response characteristics of a WPT antenna for 3D printed electronics associated with changes in its design elements. The effects of changing the antenna curvature and the gap between the wires were analyzed through experimental tests.

• Journal of Power Electronics
• /
• 제16권3호
• /
• pp.1056-1066
• /
• 2016

Wireless power transfer (WPT) technology is now recognized as an efficient means of transferring power without physical contact. However, frequency detuning will greatly reduce the transmission power and efficiency of a WPT system. To overcome the difficulties associated with the traditional frequency-tracking methods, this paper proposes a Direct Phase Control (DPC) approach, based on the Second-Order Generalized Integrator Phase-Locked Loop (SOGI-PLL), to provide accurate frequency-tracking for WPT systems. The DPC determines the phase difference between the output voltage and current of the inverter in WPT systems, and the SOGI-PLL provides the phase of the resonant current for dynamically adjusting the output voltage frequency of the inverter. Further, the stability of this control method is analyzed using the linear system theory. The performance of the proposed frequency-tracking method is investigated under various operating conditions. Simulation and experimental results convincingly demonstrate that the proposed technique will track the quasi-resonant frequency automatically, and that the ZVS operation can be achieved.

• 전기저널
• /
• 통권442호
• /
• pp.64-66
• /
• 2013