• Journal of Power System Engineering
• /
• v.13 no.6
• /
• pp.22-28
• /
• 2009

열역학 제 2법칙의 관점의 열역학적 가용에너지인 엑서지 해석법을 적용하여 가솔린, 메탄올, M90 연료를 사용한 전기점화 기관의 성능해석을 수행하였다. 열역학적 사이클 해석을 위하여 사이클을 구성하는 각 과정은 열역학적 모델로 단순화하였고, 크랭크 각도에 따른 실린더의 압력과 작동유체를 구성하는 연료, 공기 및 연소생성물의 열역학적 물성 값들을 이용하여 각 과정에서의 엑서지와 손실 일을 계산하였다. 실험데이터는 단기통 전기점화기관을 가솔린, 메탄올과 M90(메탄을 90%+부탄 10%의 혼합연료)을 연료로 WOT(Wide Open Throttle), MBT(Minimum advanced spark timing for Best Torque), 2500rpm 조건으로 운전하여 측정하였다. 계산에 이용한 자료는 실험으로 측정한 크랭크 각도에 따른 연소실의 압력, 흡입공기와 연료유량, 흡입공기 온도, 냉각수 온도와 배출가스 온도 등이다. 이를 이용하여 각 과정에서의 엑서지와 손실 일을 계산하였으며 각 과정에서의 손실 일은 연소과정에서 가장 크며 팽창과정, 배출과정, 압축과정 및 흡입과정 순으로 크게 나타났다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.6
• /
• pp.11-17
• /
• 1996

Many researches on natural gas engines, with lean mixtures are being conducted for the purpose of preservation of global environment. Lean combustion is one of the most promising method for increasing engine efficiency and reducing the emission from SI engines. Due to the possibility of partial burn and misfire, however, under lean burn operation, stable flame kernel formation and fast burn rate, by use of swirl or tumble flow, are needed to guarantee a successful subsequent combustion. Experimental data were obtained on a 4-stroke, natural gas fueled SI engine to investigate the effect of compression ratio, swirl and spark plug electrode rotation on efficiency and emission under lean burn condition. Experimental results have displayed that higher compression ratio, presence of swirl vane and favorable direction of electrode gap brougth about the improvements in engine efficiency and its operational stability.

• Journal of Energy Engineering
• /
• v.9 no.2
• /
• pp.83-88
• /
• 2000

In this study, the performance and pollutant emission of CNG engine using diesel oil as a source of ignition, so called CNG dual fuel diesel engine is considered by experiment. One of the unsolved problems of the natural gas dual fuel engine is that there is too much exhaust of total hydrocarbon (THC) at a low equivalent mixture ratio. To fix it, a natural gas mixed with hydrogen was applied to engine test. The results showed that the higher the mixture ratio of hydrogen to natural gas, the higher the combustion efficiency. and when the amount of the intake air is reached to 90% of WOT, the combustion efficiency was promoted. But, like a case making the injection timing earlier, the equivalent mixture ratio for the knocking limit decrease and the produce of NOx increases.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1999.05a
• /
• pp.95-100
• /
• 1999

One of the unsolved problems of the natural gas dual fuel engine is that there is too much exhaust of Total Hydrogen Carbon(THC) at a low equivalent mixture ratio. To fix it, a natural gas mixed with hydrohen was applied to engine test. The results showed that the higher the mixture ratio of hydrogen to natural gas, the higher the combustion efficiency. And when the amount of the intake air is reached to 90% of WOT, the combustion efficiency was promoted. But, like a case making the injection timing earlier, the equivalent mixture ratio for the nocking limit decreases and the produce of NOx increases.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.6
• /
• pp.89-94
• /
• 2006

The tire delivering power generated from engine to the ground pulls a vehicle to move. Radius of tires is changeable due to elasticity that depends on the speed of vehicle and traction force. The main objectives on this study are real time measurement of dynamic radius and slip ratio according to the speed and traction force. The dynamic radius is proportional to speed and traction force. According to measurement, the dynamic radius is increased about 3mm under 100km/h compared to stop. It is also increased about 1.5mm when a traction force is supplied as much as 4kN compared to no load state at low speed. There is no strong relationship between slip ratio and vehicle speed. The slip ratio is measured up to 4% under WOT at first stage gear. Through this research, the method of measuring dynamic radius and slip ratio is set up and is expected to be applied to the measurement of traction force in chassis dynamometer or accelerating and climbing ability.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.6
• /
• pp.31-39
• /
• 2000

In this paper, characteristics of a port injection type LPG fuel system were investigated to adopt the system to a spark ignition engine through rig test. Engine combustion characteristics for limited conditions and the precise control method of LPG fuel supply were also studied. As a basic experiment, the effects and the relationships of parameters such as orifice area, fuel delivery pressure, fuel temperature and flow coefficient were established. From this, one dimensional compressible flow equation can be applied to control gaseous fuel flow rate by setting pressure difference between vaporizer and manifold to a certain range, for example about 1.2 bar in a naturally aspirated engine. The combustion analysis results of LPG engine were also compared with those of gasoline engine according to spark timing and load change. At part load and stoichiometric condition, the MBT spark timing of LPG fueled engine is retarded by 2$^{\circ}$ - 4$^{\circ}$CA compared to that of gasoline engine. On the contrary, the spark timing of LPG fueled engine can be advanced by 5$^{\circ}$- 10$^{\circ}$ CA at WOT, which results from higher Octane Number and burned fraction of LPG fuel compared to gasoline.

• Journal of ILASS-Korea
• /
• v.14 no.1
• /
• pp.34-38
• /
• 2009

This paper presents the pulsation of carburetor inlet and outlet pressure of a small SI gasoline engine. The engine used in this paper is a 23cc, single cylinder, diaphragm carburetor, two-stroke, air-cooled for brush cutter. The rpm and pressure wave pulsation at the inlet and the outlet of carburetor were measured and analysed for the understand of the internal air flow into the barrel on the diaphragm carburetor. These data should be used for the development of the duel fuel injection system for gasoline and LPG. The results showed that the carburetor inlet pressure variations were very steady, but the pressure variations at carburetor outlet were very sensitive to the pressure variation into the crank case and were to similar independently to the engine speed on partial opened throttle conditions. According to increasing engine speed, the pressure waves started to come out and be developed after closing the intake port of the engine at carburetor outlet. Reverse flow occurred on the WOT (wide open throttle) condition.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.6
• /
• pp.94-102
• /
• 2001

The thermodynamic second law analysis, which means available energy or exergy analysis, for the indicated performance of Otto cycle engine has been carried out. Each operating process of the engine is simplified and modeled into the thermodynamic cycle. The calculation of the lost work and exergy through each process has been done with the thermodynamic relations and experimental data. The experimental data were measured from the test of single cylinder Otto cycle engine which operated at 2500 rpm, WOT(Wide Open Throttle) and MBT(Minimum advanced spark timing for Best Torque) condition with different fuels: gasoline, methanol and mixture of butane-methanol called M90. Experimental data such as cylinder pressure, air and fuel flow rate, exhaust gas temperature, inlet gas temperature and etc. were used for the analysis. The proposed model and procedure of the analysis are verified through the comparison of the work done in the study with experimental results. The calculated results show that the greatest lost work is generated during combustion process. And the lost work during expansion, exhaust, compression and induction process follows in order.

• Transactions of the Korean hydrogen and new energy society
• /
• v.18 no.1
• /
• pp.67-74
• /
• 2007

고효율의 실현이 가능한 흡기관 분사식 수소기관의 역화 억제 가능성을 파악하고자 밸브 오버랩 기간의 변화에 따른 제반 기관성능과 역화가 발생되는 역화한계 당량비를 실험적으로 해석하였다. 실험에는 기계식 연속 가변밸브 타이밍 시스템이 부착된 연구용 수소기관을 사용하였다. 밸브 오버랩기간은 배기밸브 개폐시기를 고정하고 흡기밸브 캠의 위상각을 조절하여 변화시켰다. 해석결과 밸브 오버랩 기간의 감소에 따른 제반기관성능은 통상의 기관과 유사하지만 역화한계 당량비가 확장되어 초기 단계이지만 수소기관의 역화발생에 밸브오버랩 기간이 관여하는 것이 보였다. 기관 회전수 1600 rpm, WOT의 실험 조건에서 밸브 오버랩 기간을 $20^{\circ}CA$에서 $0^{\circ}CA$로 감소시킨 경우 역화한계당량비는 약 45% 정도 확장되고 정미 토크는 16% 감소했다.

• Journal of Energy Engineering
• /
• v.20 no.2
• /
• pp.163-169
• /
• 2011

This research is to decide the possibility of using RM50(reformulated methanol fuel) without any modification of engine by the method of numerical analysis. Comparing the heat release rate, the difference among each fuel was decreased according to the increase of the engine speed, and the maximum heat release rate was higher in the order of RM50 and gasoline fuel. Also, this order corresponds to the order of burning speed. RM50 had the higher turbulent burning speed, and the curve of turbulent intensity was showed similar tendency to the curve of turbulent burning speed. RM50 had relatively high burning speed, short quenching length, high temperature in cylinder, so that it might increase NO emission, but owing to chemical reaction dynamics, it was decreased NO emission. Therefore, in order to predict the possibility of using RM50, it is needed to consider not only the temperature in cylinder by low heating value, but also combustion characteristics including burning speed.