• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.6
• /
• pp.116-126
• /
• 2008

This paper describes the Dual-band WLAN transmitter with 2.4[GHz], 5[GHz]. Dual-band WLAN transmitter was designed at 2.4[GHz] and 5[GHz]. The Dual-band WLAN transmitter has a amplifier which operate at 2.4[GHz] and 5[GHz] frequency and two VCO(Voltage Controlled Oscillator) or VCO has a wide scope of frequency. these problem cause a size and a power consumption, The Dual-band WLAN transmitter module was proposed to solve these. the transmitter was designed to get output signals of IEEE 802.11a's 5.8[GHz] band signal using frequency multiplication way or to act a amplifier about the 2.4[GHz] band signal of IEEE 802.11b/g, according to inputed frequency and bias voltage that a eve using single transmission block. The output spectrum get the improved specification of ACPR of 4[dB], 6[dB], 16[dB] at +11[MHz], +20[MHz], +30[MHz] offset of center frequency compared to no linearization, was satisfied to transmit spectrum mask of IEEE 802.11a wireless Lan.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.2
• /
• pp.341-348
• /
• 2018

A WLAN dual band dipole antenna with parasitic elements and a reflector is presented for high gain operation. The parasitic elements are used for practical application and high gain operation of the radiation pattern at the WLAN dual band. The proposed antenna consists of three layers, and has dimensions of $74mm{\times}40 mm{\times}31.4mm$. From the experimental results, the achieved impedance bandwidths were 1035 MHz (2.031-3.066 GHz) and 1119 MHz (5.008-6.127 GHz), respectively. The measured maximum gain at each WLAN band was 6.69 dBi and 7.81 dBi, respectively.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.3
• /
• pp.533-538
• /
• 2018

For WLAN dual-band operation, a modified Yagi dipole antenna is presented. The modified dipole antenna consists of a dipole antenna with open sleeves and parasitic elements. The parasitic elements are used for the practical application of the radiation patterns and high-gain operation at the WLAN dual band. The experimental results showed that the achieved impedance bandwidths were 320 MHz (2.4 to 2.72 GHz) and 640 MHz (5.04 to 5.68 GHz), respectively. The measured maximum gain at the two WLAN bands was 7.74 dBi and 6.93 dBi, respectively.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.4
• /
• pp.811-817
• /
• 2014

In this paper, a design method for a dual-band monopole antenna operating in the bands of 2.45 GHz WLAN and UWB is studied. A monopole antenna operating in UWB band is first designed, and a slot is inserted on the monopole to operate in 2.45 GHz WLAN band. The optimized dual-band monopole antenna is fabricated on an FR4 substrate, and the experimental results show that the antenna has a dual-band characterisitc in WLAN and UWB bands with the frequency bands of 2.35-2.50 GHz and 2.99-11.82 GHz for a VSWR < 2. Measured gain is 1 dBi at 2.45 GHz, and ranges 1.5-4.6 dBi in the frequency band of 3.1-10.6 GHz.

• Journal of electromagnetic engineering and science
• /
• v.4 no.3
• /
• pp.124-127
• /
• 2004

A novel printed inverted-F antenna for dual-band WLAN is presented. The proposed design is based on the folded quarter-wave antennas, which have a conductor plate having two arms. An extremely thin prototype antenna is fabricated according to the simulation result. The obtained antenna can perform in IEEE802.11a, b(2.4～2.484 GHz and 5.15～5.35 GHz bands) and be adopted for laptop applications. All the measurements are performed in the actual test fixture.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.9
• /
• pp.814-820
• /
• 2015

In this paper, A high selective dual-band bandpass filter was proposed using a dual-mode ring resonator with two short-circuited stubs. For dual-mode resonance, the ring resonator is directly connected with non-orthogonal feed-lines via coupling capacitors. Two short-circuited stubs which are unequal lengths are simultaneously placed at two corners along the two symmetry plane of the ring resonator in order to obtain dual-band responses. Because the feeding angle perturbated ring resonator of the proposed dual-band bandpass filter has the symmetrical structure, Even/Odd mode analysis can be well applied to extract the scattering parameters and transmission zero frequencies. The proposed dual-band bandpass filter was designed and fabricated for WLAN(Wireless Local Area Network) application of IEEE 802.11n standard. The measured results showed a good agreement with the simulation results, and it should be well applied not only for WLAN applications but also for any other communication systems.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.6
• /
• pp.1049-1056
• /
• 2017

In this paper, a microstrip-fed dual-band monopole antenna with two arc-shaped lines for WLAN(: Wireless Local Area Networks) applications was designed, fabricated and measured. The proposed antenna is based on a microstrip-fed structure, and composed of two arc-shaped lines and then designed in order to get dual band characteristics. We used the simulator, Ansoft's High Frequency Structure Simulator(: HFSS) and carried out simulation about parameters L2, L5, and with/without slit to get the optimized parameters. The proposed antenna is made of $13.0{\times}34.0{\times}1.0 mm^3$ and is fabricated on the permittivity 4.4 FR-4 substrate($12.0{\times}34.0{\times}1.0mm^3$). The experiment results are shown that the proposed antenna obtained the -10 dB impedance bandwidth 360 MHz (2.29~2.65 GHz) and 1,245 MHz (4.705~5.95 GHz) covering the WLAN bands. Also, the measured gain and radiation patterns characteristics of the proposed antenna are presented at required dual-band(2.4 GHz band/5.0 GHz band), respectively.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.5
• /
• pp.213-217
• /
• 2012

In this paper, we design dual-band microstrip antenna for IEEE 802.16e mobile WiMAX standard IEEE 802.11 WLAN band at the same time. To solve interference at the desired operating frequency band, impedance matching is improved and simple production method showed the characteristics of the omni-directional and compact size. The proposed structure is considered to bring the effect of the installation costs, and show the antenna for dual-band communication.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.6
• /
• pp.1049-1056
• /
• 2016

In this paper, a design method for a compact dual-band slot antenna with bent slot is studied. Bent slots are added on the rectangular slot of the proposed antenna for dual-band operation. The rectangular slot is fed by a coaxial cable by placing a rectangular feeding patch inside the slot. When the bent slots are added onto the both corner of the upper side of the rectangular slot symmetrically, a new resonant frequency is created in low frequency because of the increasement of the slot length. A prototype of the proposed dual-band slot antenna operating at 2.45 GHz WLAN band and 4.50-8.30 GHz band including 5GHz WLAN band is fabricated on an FR4 substrate with a dimension of 30 mm by 30 mm. Experiment results show that the antenna has a desired impedance characteristic with a frequency band of 2.40-2.49 GHz and 4.33-9.85 GHz for an input reflection coefficient < -10 dB.

• Journal of information and communication convergence engineering
• /
• v.15 no.4
• /
• pp.199-204
• /
• 2017

A compact dual-band half-ring-shaped (HRS) bent slot antenna fed by a coplanar waveguide for wireless local area network (WLAN) and worldwide interoperability for microwave access (WiMAX) applications is presented. The antenna consists of two HRS slots with different lengths and widths. The two HRS slots are connected through an arc-shaped slit, and the upper HRS slot is bent in order to reduce the size of the antenna. The optimized dual-band HRS bent slot antenna operating in the 2.45 GHz WLAN and 3.5 GHz WiMAX bands is fabricated on an FR4 substrate with dimensions of 30 mm by 30 mm. The slot length of the proposed dual-band slot antenna is reduced by 35%, compared to a conventional dual-band rectangular slot antenna. Experimental results show that the proposed antenna operates in the frequency bands of 2.40-2.49 GHz and 3.39-3.72 GHz for a voltage standing wave ratio of less than 2, and measured gain is larger than 1.4 dBi in the two bands.