• 한방재활의학과학회지
• /
• 제20권2호
• /
• pp.63-77
• /
• 2010

Objectives : It is known that abdominal obesity increases the possibility of cardiovascular diseases, early death, and metabolic syndrome including dyslipidemia and insulin resistance. Clinical trials have been under way to verify the effectiveness of treatment for abdominal obesity. The objective of this study is to set criteria about how effective oriental medicine and acupuncture are in abdominal obesity. Methods : I manually search "www.clinicaltrial.gov", 4 Korean medical databases and 4 Korean medical journals of abdominal obesity. Search terms used were "abdominal obesity" or "visceral obesity". In order to see detail review, searching was performed from 01, 01, 2005 to 11, 31, 2009. And I classified all the searched studies into design, intervention, purpose, end point, diseases, condition and etc. Results : 1. I could search total 67 trials in "www.clinicaltrial.gov". I found 9, 10, 13, 8, 6 clinical trial from 2005 to 2009 every year. 2. Test on both gender and adult or adult and senior have been most frequent. 3. Randomization clinical trial is 51 cases that occupied 96.2%. 38 cases use control group. 4. Body mass index(BMI) and waist circunference(WC) are major criteria of abdominal obesity clincal trial. WC, BMI, abdominal fat mass, body weight are measured at end point of abdominal obesity clincal trial. 5. I could search total 86 cases in domestic study. I found 15, 23, 23, 20, 5 cases from 2005 to 2009 every year. 6. Test on female and adult have been most frequent in domestic study. 7. Randomization clincal trial is only 2 cases that occupied 2.3%. 62 cases use control group in domestic study. 8. BMI, body fat percent, WC, visceral-subcutaneous fat ratio(VSR), waist-hip ratio(WHR) are criteria of abdominal obesity clincal trial in domestic study. WC, BMI, abdominal fat mass, body weight are measured at end point of abdominal obesity clincal trial in domestic study. Conclusions : To improve abdominal obesity study in traditional korean medicine, it is need to activate clinical trial, meta analysis, develope of clinical practice guidelines, co-works with conventional medicine and etc.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.215-216
• /
• 2002

This paper describes the wear characteristics of WC-Co cemented carbides machined with Wire-cut or Die-sinking EOM. We prepared the specimens with different grades of grinding to remove the affected layer after the EDM. These specimens were experimented by block-on-cylinder type tribometer. The result indicated that although the hardness of the affected layer was lower than that of the bulk, wear resistance was increased. In order to investigate the cause of the increase in wear resistance of the affected layer, the layer was observed and analyzed by SEM and ESCA. We also discussed the mean free path of Co phase.

• Corrosion Science and Technology
• /
• 제14권2호
• /
• pp.59-63
• /
• 2015

Airless spray which is widely used for painting to ship blocks and hull sides is the coating method for attaching atomized paint material to the substrate using spray tip nozzle with compressed air. When the paint material which has high solid contents such as epoxy primer paint is atomized by passing through spray tip nozzle with high pressure, the nozzle composed of tungsten carbide(WC) undergoes the erosive wear, leading to widening of nozzle hole. The deformation of nozzle hole induces improper spray pattern and coating failures such as finger pattern and sagging because the conditions of spray pump pressure and paint flow rate for developing full spray pattern are changed. In this study, an appropriate replacement cycle of spray tip was predicted by measuring the erosive wear tendency as increasing the spraying time of epoxy primer paint.

• 한국분말재료학회지
• /
• 제22권3호
• /
• pp.203-207
• /
• 2015

This study investigated the microstructure and wear resistance property of HPHT(high pressure high temperature) sintered PDC(polycrystalline diamond compact) in accordance with initial molding pressure. After quantifying an identical amount of diamond powder, the powder was inserted in top of WC-Co sintered material, and molded under four different pressure conditions (50, 100, 150, $200kgf/cm^2$). The obtained diamond compact underwent sintering in high pressure, high temperature conditions. In the case of the $50kgf/cm^2$ initial molding pressure condition, cracks were formed on the surface of PDC. On the other hand, PDCs obtained from $100{\sim}200kgf/cm^2$ initial molding pressure conditions showed a meticulous structure. As molding pressure increased, low Co composition within PDC was detected. A wear resistance test was performed on the PDC, and the $200kgf/cm^2$ condition PDC showed the highest wear resistance property.

• 대한화학회지
• /
• 제10권1호
• /
• pp.32-42
• /
• 1966

$CaCl_2$, CaO 및 $WO_3$로 構成되는 熔融鹽을 黑鉛 陽極과 鐵 陰極으로 電解하여 순수한 金屬텅스텐을 얻는 方法에 관하여 실험하였다. 電氣分解에 적합한 熔融浴을 選定하기 위하여 $CaCl_2$-CaO系와 $CaCl_2-CaWO_4$系에 관한 二相 狀態圖를 작성하였으며 同時에 $CaCl_2$와 $WO_3$와의 高溫下에서의 化學反應을 검토하여 安定한 電解浴을 얻기 위해서는 一定量의 CaO가 添加되어야 할 것임을 알 수 있었다. 炭素陽極을 사용하여 $WO_3$를 W와 CO로 분해시킬 때의 分解電壓은 -0.1 volt이었으며 熱力學的 計算에 의한 것은 -0.3 volt이었다. 熔融鹽을 電氣分解한 結果 金屬텅스텐이 100%에 가까운 電流效率로 電極에 析出되나 이는 陽極에서 二次的으로 발생하는 CO가스에 의하여 쉽게 WC등으로 변화하므로 순수한 텅스텐을 얻기 위해서는 電解浴의 溫度를 $1100^{\circ}C$이상으로 유지하여야 된다는 것을 알게 되었다. 電解浴의 組成은 可及的 低融點과 $WO_3$의 分解, $CaCl_2$의 蒸發 등을 억제하기 위해서는 $CaCl_2$ 100分에 대하여 CaO와 $WO_3$가 각 10 乃至 20分이 適切하였으며 CaO와 $WO_3$의 몰比率은 1이상이 요구되었다. 陰極 電流密度를 1~5 $amp/cm^2$의 範圍에서 變化시켜도 電流效率에 큰 影響이 없었다.

• 한국표면공학회지
• /
• 제40권1호
• /
• pp.23-31
• /
• 2007

The objective of this study is to investigate the effect of Al addition on the reaction behavior of cobalt with molten zinc. Pure cobalt specimen was immersion tested in the three kinds of molten zinc (pure, 0.12%Al added and 0.24%Al added) baths at $460^{\circ}C,\;490^{\circ}C\;and\;520^{\circ}C$. For the understanding of degradation processes, specimens were analyzed with scanning electron microscope (SEM) and energy dispersive spectrum (EDS), and electrochemical stripping method. When 0.12% and 0.24% Al was added in molten zinc baths, three intermetallic compounds layers of ${\gamma},\;{\gamma}_1,\;and\;{\gamma}_2$ were formed on the Co matrix and ${\beta}_1$ layer was not formed between the Co matrix and the ${\gamma}$ layer. Particles of CoAl intermetallic compound were formed at the interface between the ${\gamma}_2$ layer and zinc melt and they did not adhere to the Co-Zn intermetallic layer. Weight loss of the Co specimen increased as Al content in the molten zinc increased and the relationship of weight loss vs. immersion time followed parabolic rate law. Rate controlling process for the reaction rate of Co with Al added molten zinc was analyzed as the diffusion process of Al atom through a boundary layer between the ${\gamma}_2$ layer and the Al added zinc melt.

• Journal of Welding and Joining
• /
• 제18권3호
• /
• pp.51-59
• /
• 2000

Sink roll has been used in molten 55%Al-Zn alloy bath of continuous galvanizing line for sinking and stabilizing working steel strip in molten metal bath. In the process, the sink roll body inevitably build up dross compounds and pitting on the sink roll surface during 55%Al-Zn alloy coated strip production, and the life time of the sink roll is shorten by build up dross compounds and pitting. The present study examined the application of thermally sprayed ceramic coatings method on sink roll body for improving erosion resistance at molten 55% Al-Zn pool. In this experiment, the stainless steels such as STS 316L and STS 430F were used as the substrate materials. The CoNiCr and WE-Co powder were selected as bond coating materials. Moreover $Al_2O_3-ZrO_2-SiO_2 and ZrO_2-SiO_2$ powders selected as the top coating materials. Appearances of the specimens before and after dipping to molten 55%Al-Zn pool were compared and analyzed. As a result of this study, STS430F of substrate, WC-Co of bond spray coatings, $ZrO_2-SiO_2$ power of top spray coatings is the best quality in erosion resistance test at molten 55%Al-Zn pool

• 한국광학회:학술대회논문집
• /
• 한국광학회 2007년도 하계학술발표회 논문집
• /
• pp.243-244
• /
• 2007

본 연구에서는 성형용 코어 가공에서 초경합금(WC, Co 0.5%)의 초정밀 가공특성을 파악하기 위하여 다이아몬드 휠의 메시, 주축 회전속도, 터빈 회전속도, 이송속도 및 연삭깊이에 따른 표면거칠기를 측정하여 최적연삭조건을 규명하였다. 규명된 최적연삭가공조건을 활용하여 페러렐 연삭법으로 초정밀 연삭가공을 수행하였다. 연삭가공은 초정밀가공기(ASP01, Nachi-Fujikoshi Co., Japan)를 사용하였다. 최종 정삭가공을 수행한 비구면 성형용 코어의 형상측정결과 형상정도(PV; ${\varphi}$ 3.0mm) 0.15${\mu}m$(비구면), 0.10${\mu}m$(평면)으로 3M급 이상의 고화질 카메라폰에 채용되고 있는 비구면 Glass렌즈 양산용 성형용 코어 규격에 만족한 결과로서 본 연구에 수행된 초정밀 가공조건 및 측정방법이 매우 유효함을 알 수 있었다. 형상정도(PV) 및 표면조도(Ra) 측정은 초정밀 자유곡면 측정기(UA3P, Panasonic Co., Japan)와 3차원 표면조도 측정기(NewView5000, Zygo Co., USA)를 각각 사용하였다. 초정밀 가공된 성형용 코어면에 이온증착법을 활용하여 DLC 코팅을 수행하였다. 코팅 전후의 성형용코어를 활용하여 Glass소재(K-BK7, Sumita Co., Japan)를 최적의 성형조건(성형온도, 압력, 냉각속도)으로 성형하였다. DLC 코팅과 성형은 DLC 코팅기(NC400, Nanotech Co., Japan)와 Glass렌즈 성형기(Nano Press-S, Sumitomo Co., Japan)을 각각 사용하였다. Fig. 1은 초정밀 연삭가공, DLC 코팅막 구조, 코팅된 성형용 코어, 그리고, 성형된 비구면Glass렌즈를 각각 나타낸다.

• 대한기계학회논문집A
• /
• 제36권6호
• /
• pp.591-598
• /
• 2012

본 연구에서는 CNC선반을 사용하여 다양한 공구재질과 절삭속도에서 벌크금속유리(BMG)의 절삭 특성을 평가하였다. 선반가공시 Zr-기 BMG의 표면거칠기와 칩 형상을 관찰하여 가공조건에 따른 절삭력과 공구툴 마모 등 절삭 특성을 비교 검토하였다. 직경 8 mm $Zr_{50}Cu_{40}Al_{10}$ BMG시험편의 절삭에는 네 종류의 절삭공구를 사용하였다. 가공후 BMG 시험편의 표면거칠기를 측정하였고, 표면거칠기에 미치는 공구 회전속도의 영향을 조사하였다. 회전속도가 빠를수록 낮은 표면거칠기를 나타내었고, 공구 재질의 영향도 크게 나타났다. 칩 형상의 관찰 결과, 산화를 일으키지 않은 BMG 칩은 단열 전단띠 발생과 함께 나선형상의 형태를 나타내지만, 산화를 일으킨 칩은 국부적으로 용융과 함께 칩들이 뭉치는 현상을 나타내었다. BMG시험편을 가공하는 동안 발생한 절삭력은 TiN-WC에서 가장 큰 값을 나타내고, PCD가 그 다음, Cermet툴에서 가장 작은 값을 나타내었다.

• Journal of Mechanical Science and Technology
• /
• 제18권5호
• /
• pp.770-779
• /
• 2004

This paper describes the micro cutting of wear resistant tungsten carbides using PCD (Poly-Crystalline Diamond) cutting tools in performance with SEM (Scanning Electron Microscope) direct observation method. Turning experiments were also carried out on this alloy (V50) using a PCD cutting tool. One of the purposes of this study is to describe clearly the cutting mechanism of tungsten carbides and the behavior of WC particles in the deformation zone in orthogonal micro cutting. Other purposes are to achieve a systematic understanding of machining characteristics and the effects of machining parameters on cutting force, machined surface and tool wear rates by the outer turning of this alloy carried out using the PCD cutting tool during these various cutting conditions. A summary of the results are as follows: (1) From the SEM direct observation in cutting the tungsten carbide, WC particles are broken and come into contact with the tool edge directly. This causes tool wear in which portions scrape the tool in a strong manner. (2) There are two chip formation types. One is where the shear angle is comparatively small and the crack of the shear plane becomes wide. The other is a type where the shear angle is above 45 degrees and the crack of the shear plane does not widen. These differences are caused by the stress condition which gives rise to the friction at the shear plane. (3) The thrust cutting forces tend to increase more rapidly than the principal forces, as the depth of cut and the cutting speed are increased preferably in the orthogonal micro cutting. (4) The tool wear on the flank face was larger than that on the rake face in the orthogonal micro cutting. (5) Three components of cutting force in the conventional turning experiments were different in balance from ordinary cutting such as the cutting of steel or cast iron. Those expressed a large value of thrust force, principal force, and feed force. (6) From the viewpoint of high efficient cutting found within this research, a proper cutting speed was 15 m/min and a proper feed rate was 0.1 mm/rev. In this case, it was found that the tool life of a PCD tool was limited to a distance of approximately 230 m. (7) When the depth of cut was 0.1 mm, there was no influence of the feed rate on the feed force. The feed force tended to decrease, as the cutting distance was long, because the tool was worn and the tool edge retreated. (8) The main tool wear of a PCD tool in this research was due to the flank wear within the maximum value of $V_{max}$ being about 260 $\mu\textrm{m}$.