• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.5
• /
• pp.270-276
• /
• 2023

In this study, we analyzed two types of cold forging dies commonly used for manufacturing general nuts and screws to investigate the differences in WC powder according to the lifespan. For both Type I and Type II dies, it was observed that as the lifespan of the molds increases, the area fraction of Co becomes larger and the size of the powder becomes smaller. Moreover, there is a trend where the strength also increases as the lifespan gets longer. Actually, the hardness value of the sample with the longest lifespan is ~ 131 HV higher than the specimen of the shortest lifespan, It is noted that the reduction in toughness of the WC-Co mold is caused by insufficient Co and the decrease in contact surface area of WC-Co results in a reduced bonding surface area. The lifespan of cold-working WC molds increases when the W content and the volume fraction of WC are high, and the size of the WC powder is small. The results can significantly enhance producing high-quality molds with an extended lifespan using WC powder for cold forging.

• Journal of Animal Science and Technology
• /
• v.47 no.6
• /
• pp.1075-1080
• /
• 2005

The objective of this experiment was conducted to evaluate the effect of various legumes in mixtures: AA mixtures(orchardgrass 40%+tall fescue 25%+Kentucky bluegrass 15%+alfalfa 20%), RC mixtures (orchardgrass 40% + tall fescue 25% + Kentucky bluegrass 15% + red clover 20%) and WC mixtures (orchardgrass 50% + tall fescue 25% + Kentucky bluegrass 15% + white clover 10%). The field trials were conducted from 2000 to 2003 at Chungnam National University in order to evaluate the dry matter yield and forage quality on different legumes in mixtures. The dry matter yield was significantly higher in WC mixtures than in other mixtures(p<0.05). In the chemical composition, the content of crude protein and dry matter digestibility were higher in WC mixtures than in other mixtures. However, the content of fibrous constituents of WC mixtures was lower than in other mixtures. The yields of crude protein dry matter and digestible dry matter were significantly higher in WC mixtures than in other mixtures. In botanical composition of alfalfa, red clover and white clover in each mixture were maintained 21%, 36% and 48% respectively, at the last cutting time in 2003. The results of this experiment indicated that WC mixtures were more effective in enhancing the DM yield and forage quality, but it needs to control the optimum botanical composition of WC.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.255-255
• /
• 2013

WC-Co 초경합금은 실온경도, 고온경도, 강도, 내마모, 내충격 등 기계적 특성이 우수하여 공구재료, 절삭공구 및 고압용 부품 등 다양한 응용분야를 가지고 있으며 WC-Co 분말 코팅같은 경우 항공분야, 일반 공업 분야에 내마모 특성 및 내열특성 향상을 위한 코팅용 소재로서 활용되어 지고 있다. 활용분야가 넓은 WC-Co 초경합금의 제조방법은 WC, Co 분말을 혼합하여 약 900도에서 1차 예비소결 후 원하는 형상 가공 후 약 1,300~1,600도에서 2차 소결을 진행한다. 지금 현재 초경분말의 조성, 크기와 같은 변수들에 따른 초경합금의 기계적 특성 변화에 대한 연구가 계속적으로 진행되고 있다. 본 연구에서는 WC-Co 분말의 소결 특성을 향상시키고자 Planetary ball mill 장비를 활용하여 볼 밀링 공정을 진행하였고 Spark plasma sintering 장비를 활용하여 빠른 소결을 진행하였다. WC-Co 분말의 미세구조, 입도, 조성 및 분산의 변화를 관찰하기 위해 볼 밀링 전, 후 분말을 분석하였고 제조된 분말의 소결 특성을 확인하기 위해 상용화 된 WC-Co 분말의 소결 특성과 비교 평가하였다. 분석 결과 볼 밀링 공정 후 분말은 약 15 ${\mu}m$에서 4.4 ${\mu}m$로 미세해지는 것을 확인하였고 밀링 후 분말로 초경합금을 제작하였을 때 기존 상용화 초경합금제작 온도보다 약 100~400도 낮아지면서 경도 값은 약 20% 향상된 것을 확인할 수 있었다.

• Journal of Welding and Joining
• /
• v.18 no.6
• /
• pp.102-107
• /
• 2000

It was attempted to improve the wear resistance of Al alloy under the load condition by making a formation of the thick surface hardening alloy layers. The thick surface hardening alloy layers were formed on 6061 Al alloys overlayed by MIG welding process with WC-12%Co powder addition. Effects of the dispersion of WE-12%Co powders on hardness and wear characteristics of alloys were investigated. The following results were obtained. Most of WE-12%Co powders are dispersed nearly uniform as unmelted particles in the matrix alloy. A part of WC-12%Co powders are melted in the molten pool, and during solidification {TEX}$Al_{9}Co_{2}${/TEX} appeared. With increasing addition of WC-12%Co powders, the hardness and specific wear resistance of the overlay weld alloys increased and reached Hv450 at WC-12%Co powder addition rate of 54g/min. It is considered that excellent wear resistance of the overlayed alloys was due to dispersed WC-12%Co powders and increased 10 times at WC-12%Co powder addition rate of 54 g/min than that of the WC-free overlaying layers.

• Journal of Powder Materials
• /
• v.12 no.2 s.49
• /
• pp.112-116
• /
• 2005

In the present study, the focus is on the analysis of carbothermal reduction of oxide powder prepared from waste WC/Co hardmetal by solid carbon under a stream of argon for the recycling of the WC/Co hard-metal. The oxide powder was prepared by the combination of the oxidation and crushing processes using the waste $WC-8 wt.\%Co$ hardmetal as the raw material. This oxide powder was mixed with carbon black, and then this mixture was carbothermally reduced under a flowing argon atmosphere. The changes in the phase structure and gases discharge of the mixture during carbothermal reduction was analysed using XRD and gas analyzer. The oxide powder prepared from waste $WC-8wt.\%Co$ hardmetal has a mixture of $WO_{3} and CoWO_{4}$. This oxide powder reduced at about $850^{\circ}C$, formed tungsten carbides at about $950^{\circ}C$, and then fully transformed to a mixed state of tungsten carbide (WC) and cobalt at about $1100^{\circ}C$ by solid carbon under a stream of argon. The WC/Co composite powder synthesized at $1000^{\circ}C$ for 6 hours from oxide powder of waste $WC-8wt.\%Co$ hardmetal has an average particle size of $0.3 {\mu}m$.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.2
• /
• pp.113-120
• /
• 2010

Air-cathode microbial fuel cell consisted of 4 unit cells were operated under batch condition and electricity generation and microbial community structure variation were investigated, depending on separator types and cathode characteristics: A) PEM(Proton Exchange Membrane)-30% Wet proofing Carbon Cloth(WC), B) AEM(Anion Exchange Membrane-WC, C) CEM(Cation Exchange Membrane)-WC, D) PEM-No Wet proofing Carbon Cloth(NC). Maximum power densities of PEM-WC, AEM-WC and CEM-WC were 510.9, 522.1 and 504.8 $mW/m^2$, respectively. But PEM-NC showed relatively lower maximum power density of 218.3 $mW/m^2$. And PEM-WC, AEM-WC and CEM-WC showed similar internal resistances(20.0-28.2 ${\Omega}$). PCRDGGE, PCA and diversity indices showed that uncultured bacteria which reported in previous MFC studies were detected in suspended growth bacteria and attached growth bacteria would be affected not by separator type but by cathode characteristic. Thus, cathode characteristic can be one of the critical factors for power generation in air-cathode MFC using PEM, AEM, and CEM as separator.

• Journal of Powder Materials
• /
• v.14 no.2 s.61
• /
• pp.132-139
• /
• 2007

In the Ti(CN)-Co/Ni cermet, WC is an effective additive for increasing sinterability and mechanical properties such as toughness and hardness. In this work, WC, (WTi)C and (WTi)(CN) were used as the source of WC and their effects were investigated in the respect of microstructural evolution and mechanical properties. Regardless of the kinds of WC sources, the hard phase with dark core and bright rim structure was observed in the Ti(CN)-Co/Ni cermet under the incorporation of relatively small amount of WC. However, hard phases with bright core began to appear and their frequency increased with the increase of all kinds of WC source addition. The ratio of bright core to dark one in the (TiW)(CN)-Co/Ni cermet was greatest under the incorporation of (WTi)C compared at the same equivalent amount of WC. The mechanical properties were improved with the addition of WC irrespective of the kinds of sources, but the addition of (WTi)(CN) was less effective for the increase of fracture toughness.

• Journal of the Korean institute of surface engineering
• /
• v.36 no.1
• /
• pp.79-84
• /
• 2003

$WC-Ti_{1}$ -xA $l_{x}$ N multilayered coatings are performed by their periodically repeated structures of lamellae of WC-Ti/$WC-Ti_{1}$ -xA $l_{x}$ Nmaterials. The $WC-Ti_{1}$ -xA $l_{x}$ N coatings with variable Al content were deposited onto AISI D2 steel by cathodic arc deposition (CAD) method. The electrochemical behavior of multilayered $WC-Ti_{1}$ -xA $l_{x}$ N coatings with different phases (WC- Ti$0.6/Al_{0.4}$ N, $WC-Ti_{0.53}$$Al_{0.47}$N, $WC-Ti_{0.5}$ $Al_{0.5}$ N and $WC-Ti_{ 0.43}$$Al_{0.57}$ N) was investigated in deaerated 3.5% NaCl solution at room temperature. The corrosion behaviors for the multilayered coatings were investigated by electrochemical techniques (potentiodynamic polarization) and surface analyses (X-ray diffraction (XRD), scanning electron microscopy (SEM), and glow discharge optical emission spectroscopy (GDOES)). In the petentiodynamic polarization test, the corrosion current density of $WC-Ti_{0.5}$$Al_{0.5}$N was lower than others.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.5
• /
• pp.435-444
• /
• 2001

WC-( $Ti_{1-x}$ A $l_{x}$) N coatings of constant changing Al concentration were deposited on S45C substrates by high-ionization sputtered PVD method. The Al concentration could be controlled by using evaporation source for Al and fixing the evaporation rate of the metals (i.e, WC- $Ti_{0.86}$A $l_{0.14}$N, WC- $Ti_{0.72}$A $l_{0.28}$N, and WC- $Ti_{0.58}$A $l_{0.42}$N). The corrosion behavior of WC-( $Ti_{1-x}$ A $l_{x}$)N coatings in a deaerated 3.5% NaCl solution was investigated by electrochemical corrosion tests and surface analyses. The measured galvanic corrosion currents between coating and substrate indicated that WC- $Ti_{0.72}$A $l_{0.28}$N coating showed the best resistance of the coating tested. The results of potentiodynamic polarization tests showed that the WC- $Ti_{0.72}$A $l_{0.28}$N coating deposited with 32W/c $m^2$ of Al target revealed higher corrosion resistance. This indicated that the WC- $Ti_{0.72}$A $l_{0.28}$N coating is effective in improving corrosion resistance. In EIS, the WC- $Ti_{0.72}$A $l_{0.28}$N coating showed one time constant loop and increased a polarization resistance of coating ( $R_{coat}$) relative to other samples. Compositional variations of WC-( $Ti_{1-x}$ A $l_{x}$)N coatings were analyzed by EDS and XRD analysis was performed to evaluate the crystal structure and compounds formation behavior. Surface morphologies of the films were observed using SEM and AFM. Scratch test was performed to measure film adhesion strength.strength. adhesion strength.strength.

• Journal of the Korean Ceramic Society
• /
• v.51 no.5
• /
• pp.442-446
• /
• 2014

Influences of Co and inhibitors from nano-sized WC materials were observed in the sintering process. VC and $Cr_3C_2$ were used as inhibitors. The crystal structure and surface images of sintered nano-sized WC materials, as functions of Co and inhibitors, were evaluated by XRD and FE-SEM analyses. The relative densities of sintered nano-sized WC materials did not change even with increased quantity of Co and increased temperature. The density of sintered nano-sized WC materials with inhibitors was lower than that of sintered nano-sized WC materials without inhibitors. No difference in hardness due to change of inhibitors was found.