• Geophysics and Geophysical Exploration
• /
• v.8 no.2
• /
• pp.145-155
• /
• 2005

A two-dimensional (2-D) interpretation of MT data has been performed for the purpose of fracture detection for geothermal development. Remote stations have been operated in Kyushu, Japan (480 km apart) as well as in Korea (60 km and 165 km apart in 2002 and 2003 data set, respectively). Apparent resistivity and phase curves calculated by remote processing with the Japan remote data showed enough quality for 2-D inversion for the whole frequency range. Remote reference processing with Korea remote reference data also showed quite good continuity in apparent resistivity and phase curves except some noisy frequency bands; around the power frequency, 60 Hz, and around the dead band $10^{-1}Hz\;Hz\;\~1\;Hz$, where the natural EM signal is known to be very weak. Even though the subsurface showed severe three-dimensional (3-D) characteristics in the survey area so that 2-D inversion by itself could not give enough information for deep geological structures, the 2-D inversion for the 5 survey lines showed several common features. The conductive semi-consolidate mudstone layer is dipping from north to south (about 500 m depth on the south and 200 m on the north most part of the survey area). The boundary between the low (L-2) and high (H-2) resistivity anomalies can be thought as a major fault with strike $N15^{\circ}E$, passing through the sites 206, 112 and 414. The shallow (< 1 km) conductive anomalies (L-4) seem to be fracture zones having strike E-W (at site 105) and $N60^{\circ}W$ (at site 434). And there exists a conductive layer in the western and west-southern part of the survey area in the depth below $2\~3\;km$, for which further investigation is to be needed.

• Parasites, Hosts and Diseases
• /
• v.26 no.2
• /
• pp.73-86
• /
• 1988

The sensitivity and specificity of crude and affinity-purified antigens of Clcnorchis sinensis obtained from the infected rabbits were studied. Stage-specific antigenic proteins from the eggs, metacercariae and adult worms were characterized by SDS-polyacrylamide gel electrophoresis (SDS-PAGE) and enzyme-linked immunosorbent astray (ELISA). The results were as follows: 1. The antibody.binding antigen (ABA) purified from whole worm crude antigen (IVWA) by CNBr-activated Sepharose 4B affinity chromatography made :l specific bands against rabbit antisera on Ouchterlony gel diffusion plate, while WWA made 7 bands. Major WWA protein bands by SDS-PAGE were found at 16, 300~18, 500 and 28, 000~29, 000 daltons, while major ABA protein bands were at 18, 000~21, 000 and 29, 000~31, 000 daltons. The reactivity of ABA with rabbit anti-sera in ELISA was remarkably less sensitive than that of WWA. 2. Molecular weights of egg antigen (EGA), metacercarial antigen (MEA) and adult worm antigen (WWA) of C. sinensis ranged from 15, 000-200, 000 daltons, 15, 000-100, 000 daltons and 11, 000~80, 000 daltons, respectively. Major WWA proteins consisted mainly of polypeptide bands of low molecular weight, less than 31, 000 daltons, while those of EGA and MEA consisted of higher molecular T.eights than 30, 000 daltons. 3. The ELISA reactivities of WWA to rabbit anti.sera were remarkably greater than those of MEA. EGA showed negative reaction throughout the experiments. WWA showed higher optical density (O.D.) than 1.0, when reacted with rabbit anti-sera obtained at 4~6 weeks after the infection. In the rabbit anti-sera later than 12 weeks after the infection, the O.D. reacting witll WWA showed a plateau without variation. MEA shoT.ed relatively low O.D. values (<0.6), when reacted with anti-sera from lightly in(ected groups throughout the experiments, althougll there were some wealth positive cases (O.D.>0.6) ill heavily infected groups. MEA reacted with rabbit anti-sera showed negative results on Ouchterlony gel diffusion plates. Summarizing the above results, it is suggested that the whole worm antigen prepared from the adult worms of C. sinensis is most highly antigenic. However, this antigen might reveal cross reactions with other trematodes such as Paragonimus westermani, therefore, purification of antigenic proteins from the crude antigen is essential 18 increase the sensitivity and specificity for the immuncdiagnosis of clonorchiasis.

• Journal of Animal Science and Technology
• /
• v.45 no.6
• /
• pp.911-916
• /
• 2003

The mitochondrial DNA(mtDNA) D-loop region was amplified from Duroc(Sus scrofa) by polymerase chain reaction(PCR). The oligonucleotide primer used to amplify the Sus scrofa mtDNA D-loop region was designed using tRNA-Pro and tRNA-Phe sequence in mtDNA regions highly conserved in many other animal species. There were 1,145 base pairs(bp) in the D-loop region. The middle of the region contained 10 tandem repeat of an 10-bp Sus scrofa-specific sequence, TACACGTGCG. We designed primers for PCR-mediated single stranded conformation polymorphism(SSCP) analysis that amplified a 345 bp fragment, which contained the most variable region according to our sequencing data. SSCP analysis of denatured amplification products was carried out by polyacrylamide(8%) gel electrophoresis followed by ethidium bromide staining. The SSCP analysis identified two band patterns(A and B) and comparision of these two nucleotide sequences identified 21 base substitutions. These results show that SSCP analysis of the D-loop region is useful for detecting the genetic polymorphism.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.2
• /
• pp.629-635
• /
• 2012

Two novel conjugated copolymers utilizing 4,7-dithien-2-yl-2,1,3-benzothiadiazole (DTBT) coupled with cyano (-CN) substituted vinylene, as the electron deficient moeity, have been synthesized and evaluated in bulk heterojunction solar cell. The electron deficient moeity was coupled with carbazole and fluorene unit by Knoevenagel condition to provide poly(bis-2,7-((Z)-1-cyano-2-(5-(7-(2-thienyl)-2,1,3-benzothiadiazol-4-yl)-2-thienyl)ethenyl)-alt-9-(1-octylnonyl)-9H-carbazol-2-yl-2-butenenitrile) (PCVCNDTBT) and poly(bis-2,7-((Z)-1-cyano-2-(5-(7-(2-thienyl)-2,1,3-benzothiadiazol-4-yl)-2-thienyl)ethenyl)-alt-9,9-dihexyl-9H-fluoren-2-yl) (PFVCNDTBT). The optical band gaps of PCVCNDTBT (1.74 eV) and PFVCNDTBT (1.80 eV) are lower than those of PCDTBT (1.88 eV) and PFVDTBT (2.13 eV), which is advantageous to provide better coverage of the solar spectrum in the longer wavelength region. The high $V_{oc}$ value of the PSC of PCVCNDTBT (~0.91 V) is attributed to its lower HOMO energy level ( 5.6 eV) as compared to PCDTBT ( 5.5 eV). Bulk heterojunction solar cells based on the blends of the polymers with [6,6]phenyl-$C_{61}$-butyric acid methyl ester ($PC_{61}BM$) gave power conversion efficiencies of 0.76% for PCVCNDTBT under AM 1.5, 100 mW/$cm^2$.

• Korean Journal of Materials Research
• /
• v.22 no.4
• /
• pp.180-184
• /
• 2012

Nanostructures of ZnO, such as nanowires, nanorods, nanorings, and nanobelts have been actively studied and applied in electronic or optical devices owing to the increased surface to volume ratio and quantum confinement that they provide. ZnO seed layer (about 40 nm thick) was deposited on Si(100) substrate by RF magnetron sputtering with power of 60 W for 5 min. ZnO nanorods were grown on ZnO seed layer/Si(100) substrate at $95^{\circ}C$ for 5 hr by hydrothermal method with concentrations of $Zn(NO_3)_2{\cdot}6H_2O$ [ZNH] and $(CH_2)_6N_4$ [HMT] precursors ranging from 0.02M to 0.1M. We observed the microstructure, crystal structure, and photoluminescence of the nanorods. The ZnO nanorods grew with hexahedron shape to the c-axis at (002), and increased their diameter and length with the increase of precursor concentration. In 0.06 M and 0.08 M precursors, the mean aspect ratio values of ZnO nanorods were 6.8 and 6.5; also, ZnO nanorods had good crystal quality. Near band edge emission (NBE) and a deep level emission (DLE) were observed in all ZnO nanorod samples. The highest peak of NBE and the lower DLE appeared in 0.06 M precursor; however, the highest peak of DLE and the lower peak of NBE appeared in the 0.02 M precursor. It is possible to explain these phenomena as results of the better crystal quality and homogeneous shape of the nanorods in the precursor solution of 0.06 M, and as resulting from the bed crystal quality and the formation of Zn vacancies in the nanorods due to the lack of $Zn^{++}$ in the 0.02 M precursor.

• Journal of the Institute of Convergence Signal Processing
• /
• v.14 no.2
• /
• pp.136-146
• /
• 2013

In this paper, the residual delay compensation algorithm is proposed for FX-type KJJVC. In case of initial version as that design algorithm of KJJVC, the integer calculation and the cos/sin table for the phase compensation coefficient were introduced in order to speed up of calculation. The mismatch between data timing and residual delay phase and also between bit-jump and residual delay phase were found and fixed. In final design of KJJVC residual delay compensation algorithm, the initialization problem on the rotation memory of residual delay compensation was found when the residual delay compensated value was applied to FFT-segment, and this problem is also fixed by modifying the FPGA code. Using the proposed residual delay compensation algorithm, the band shape of cross power spectrum becomes flat, which means there is no significant loss over the whole bandwidth. To verify the effectiveness of proposed residual delay compensation algorithm, we conducted the correlation experiments for real observation data using the simulator and KJJVC. We confirmed that the designed residual delay compensation algorithm is well applied in KJJVC, and the signal to noise ratio increases by about 8%.

• Journal of Life Science
• /
• v.18 no.7
• /
• pp.968-973
• /
• 2008

The study was to provide basic data and to examine the effect of combined exercise for 12 months on functional fitness and bone mineral density (BMD) in breast cancer survivors. The subjects of this study were 40 to 60-year-old married women (N=24) who finished their treatments chemotherapy and radiation therapy. They were divided into two groups that exercise group and exercise with alendronate group. Eighteen (T-score=$-2.2{\pm}0.8$) of the 24 women who were diagnosed osteopenia (N=15) and osteoporosis (N=3), participated in combined exercise (EG). The other six (T-score=$-4.6{\pm}0.9$) women who were diagnosed as osteoporosis (EDG), participated in the combined exercise program with osteoporosis drug (Alendronate 70 mg/w). The result of the analysis was as follows: Twelve months after, the participants (N=24) had a significant increase of the items such as sit and reach ups, grip strength (R and L) and sit ups test of functional fitness in the periods. In body composition, FM (fat mass) had significant decrease in periods. In the comparison of BMD, EG (N=18) had no change, while EDG (N=6) had significant improvement in L1, T12 and T-score after 12months. Consequently, complex exercise program (Hatha yoga, elastic band, gym ball) had positive effect on functional fitness and bone mineral density. We suggest that complex exercise program can be applied as recovery program after breast cancer surgery. Further research needs various and repetitive studies from more different targets or methods in the exercise program for its improvement.

• Journal of the Korean Ceramic Society
• /
• v.44 no.3 s.298
• /
• pp.147-151
• /
• 2007

An improvement for the efficiency of the $Sr_{2}SiO_{4}:Eu$ yellow phosphor under the $450{\sim}470\;nm$ excitation range have been achieved by adding the co-doping element ($Mg^{2+}\;and\;Ba^{2+}$) in the host. White LEDs were fabricated through an integration of an blue (InGaN) chip (${\lambda}_{cm}=450\;nm$) and a blend of two phosphors ($Mg^{2+},\;Ba^{2+}\;co-doped\;Sr_{2}SiO_{4}:Eu$ yellow phosphor+CaS:Eu red phosphor) in a single package. The InGaN-based two phosphor blends ($Mg^{2+},\;Ba^{2+}\;co-doped\;Sr_{2}SiO_{4}:Eu$ yellow phosphor+CaS:Eu red phosphor) LEDs showed three bands at 450 nm, 550 nm and 640 nm, respectively. The 450 nm emission band was due to a radiative recombination from an InGaN active layer. This 450 nm emission was used as an optical transition of the $Mg^{2+},\;Ba^{2+}\;co-doped\;Sr_{2}SiO_{4}:Eu$ yellow phosphor+CaS:Eu red phosphor. As a consequence of a preparation of white LEDs using the $Mg^{2+},\;Ba^{2+}\;co-doped\;Sr_{2}SiO_{4}:Eu$ yellow phosphor+CaS:Eu red phosphor yellow phosphor and CaS:Eu red phosphor, the highest luminescence efficiency was obtained at the 0.03 mol $Ba^{2+}$ concentration. At this time, the white LEDs showed the CCT (5300 K), CRI (89.9) and luminous efficacy (17.34 lm/W).

• Investigative Magnetic Resonance Imaging
• /
• v.6 no.1
• /
• pp.41-46
• /
• 2002

The Fourier transform arteriography (FTA) exploits the periodic variation of arterial flow velociety of arterial flow velocity in stnchronized with cardiac cycles. This technique is intrinsically unique compared to other modern techniques. This technique separates the arteries from the veins using the pulsatile arterial flow without using the presaturation RF pulses. Therefore, it has less RF deposition and is free from the dark band artifacts that can arise from retrograde flow and curved arteries. Furthermore, it is free from the artifacts induced by eddy currents. However, there are some drawbacks such as a single projection view and the saturation of arteries at the end of an imaging slab. These drawbacks are circumvented by applying recently developed techniques. The fast gradient switching capability of modern MRI systems enabled us to incorporate dual projection views into the conventional FTA sequence without increasing the repetition time. In addition, signals from the distal arteries were enhanced by use of a ramped RF pulse and therefore the distal arteries were less saturated. By use of the FTA sequence with dual projection views and the ramped RF pulse, we acquired the sagittal and coronal projection views of femoral arteriograms simultaneously with more enhanced signals of distal arteries than the conventional FTA.

• The Journal of the Acoustical Society of Korea
• /
• v.18 no.5
• /
• pp.68-77
• /
• 1999

The paper looked into the effects of the spectral properties (waveform) of the high intensity focused ultrasound on suppression of the ultrasonic cavitation. Three different types of ultrasound were considered in the study, which were sinusoidal (1 MHz, 5 MPa), frequency modulated (from 1 MHz to 6 MHz for 10 ㎲, 5 MPa), asymmetrically shocked (fundamental frequency 1 MHz, peak positive pressure 12 MPa, peak negative pressure -4 MPa). The temporal response of an air bubble in water initially 1 ㎛ in radius to each type of the ultrasound was predicted using Gilmore bubble dynamic model and Church's rectified gas diffusion equation. It was shown that the radially pulsating amplitude of the bubble was greatly reduced for the frequency modulated wave and was little decreased for the shock wave, compared to the case that the bubble was exposed to the sinusoidal wave. It is interesting that the bubble response to the frequency modulated wave remains similar when the frequency component of the modulated ultrasound is beyond the bubble resonant frequency 3 MHz. This implies that, although the ultrasound is modulated up to 3MHz rather than up to the present 6 MHz, it is likely to produce similar cavitation suppression effects. In practice, it means that a typical narrow band ultrasonic transducer can be taken to generate an appropriate frequency modulated ultrasound to reduce cavitation activity. The present study indicates that ultrasonic cavitation may be suppressed to some extent by a proper spectral modification of high intensity ultrasound.