• Journal of Bio-Environment Control
• /
• v.24 no.2
• /
• pp.100-105
• /
• 2015

The calculation method of infiltration loss in greenhouse has different ideas in each design standard, so there is a big difference in each method according to the size of greenhouses, it is necessary to establish a more accurate method that can be applied to the domestic. In order to provide basic data for the formulation of the calculation method of greenhouse heating load, we measured the infiltration rates using the tracer gas method in plastic greenhouses equipped with various thermal curtains. And then the calculation methods of infiltration loss in greenhouses were reviewed. Infiltration rates of the multi-span and single-span greenhouses were measured in the range of $0.042{\sim}0.245h^{-1}$ and $0.056{\sim}0.336h^{-1}$ respectively, single-span greenhouses appeared to be slightly larger. Infiltration rate of the greenhouse has been shown to significantly decrease depending on the number of thermal curtain layers without separation of single-span and multi-span. As the temperature differences between indoor and outdoor increase, the infiltration rates tended to increase. In the range of low wind speed during the experiments, changes of infiltration rate according to the outdoor wind speed could not find a consistent trend. Infiltration rates for the greenhouse heating design need to present the values at the appropriate temperature difference between indoor and outdoor. The change in the infiltration rate according to the wind speed does not need to be considered because the maximum heating load is calculated at a low wind speed range. However the correction factors to increase slightly the maximum heating load including the overall heat transfer coefficient should be applied at the strong wind regions. After reviewing the calculation method of infiltration loss, a method of using the infiltration heat transfer coefficient and the greenhouse covering area was found to have a problem, a method of using the infiltration rate and the greenhouse volume was determined to be reasonable.

• Journal of Bio-Environment Control
• /
• v.29 no.2
• /
• pp.141-152
• /
• 2020

The rapid on-site measurement of hydroponic nutrients allows for the more efficient use of crop fertilizers. This paper reports on the development of an embedded on-site system consisting of multiple ion-selective electrodes (ISEs) for the real-time measurement of the concentrations of macronutrients in hydroponic solutions. The system included a combination of PVC ISEs for the detection of NO₃, K, and Ca ions, a cobalt-electrode for the detection of H₂PO₄, a double-junction reference electrode, a solution container, and a sampling system consisting of pumps and valves. An Arduino Due board was used to collect data and to control the volume of the sample. Prior to the measurement of each sample, a two-point normalization method was employed to adjust the sensitivity followed by an offset to minimize potential drift that might occur during continuous measurement. The predictive capabilities of the NO₃ and K ISEs based on PVC membranes were satisfactory, producing results that were in close agreement with the results of standard analyzers (R² = 0.99). Though the Ca ISE fabricated with Ca ionophore II underestimated the Ca concentration by an average of 55%, the strong linear relationship (R² > 0.84) makes it possible for the embedded system to be used in hydroponic NO₃, K, and Ca sensing. The cobalt-rod-based phosphate electrodes exhibited a relatively high error of 24.7±9.26% in the phosphate concentration range of 45 to 155 mg/L compared to standard methods due to inconsistent signal readings between replicates, illustrating the need for further research on the signal conditioning of cobalt electrodes to improve their predictive ability in hydroponic P sensing.

• Geophysics and Geophysical Exploration
• /
• v.13 no.4
• /
• pp.357-363
• /
• 2010

In this study, we investigated the geologic structure of the basement and overlying sediments of the construction site of the dinosaur egg fossil museum in Hwasung, Gyeonggi Province through refraction seismology, drilling, and downward seismic velocity measurements in the drill holes. The construction site ($350{\times}750\;m^2$) is located in the reclaimed area south of Sihwa Lake, Gojeong-ri. About 6,950 m of seismic refraction data consisting of 11 lines were acquired using a sledge hammer source. Drilling to the basement was performed at five sites. Sediment samples from drilling were analysed for grain-size distribution and age dating. At two drill holes, seismic velocity was measured with depth using a hammer as a seismic source. The geological structure of the study area consists of, from top to bottom, a tidal flat layer (5 ~ 12 m thick), a weathered soil layer (2 ~ 8 m thick), and the basement. The basement is interpreted as Cretaceous sedimentary rocks that tend to be shallow eastward. The volume of the tidal flat sediments and weathered soil in the study area is estimated as $1.4{\times}10^6\;m^3$, weighing $3.5{\times}10^6$ tons. The rate of sea level rise since 8,000 yrs BP is estimated to be 0.1 ~ 0.15 cm/yr.

• The Journal of the Petrological Society of Korea
• /
• v.17 no.1
• /
• pp.16-35
• /
• 2008

We study metamorphism of metasedimetary rocks and origin and evolution of leucogranite form Samcheok area, northeastern Yeongnam massif, South Korea. Metamorphic rocks in this area are composed of metasedimentary migmatite, biotite granitic gneiss and leucogranite. Metasedimentary rocks, which refer to major element feature of siliclastic sediment, are divided into two metamorphic zones based on mineral assemblages, garnet and sillimanite zones. According to petrogenetic grid of mineral assemblages, metamorhpic P-T conditions are $740{\sim}800^{\circ}C$ at $4.8{\sim}5.8\;kbar$ in the garnet zone and $640-760^{\circ}C$ at 2.5-4.5kbar in sillimanite zone. The leucogranite (Imwon leucogranite) is peraluminous granite which has high alumina index (A/CNK=1.31-1.93) and positive discriminant factor value (DF > 0). Thus, leucogranite is S-type granite generated from metasedimentary rocks. Major and trace element diagram ($R_1-R_2$ diagram and Rb vs. Y+Nb etc.) show collisional environment such as syn-collisional or volcanic arc granite. Because Rb/sr ratio (1.8-22.9) of leucogranites is higher than Sr/Ba ratio (0.21-0.79), leucogranite would be derived from muscovite dehydrate melting in metasedimentary rocks. Leucogranites have lower concentration of LREE and Eu and similar that of HREE relative to metasedimentary rocks. To examine difference of REEs between leucogranites and metasedimentary rocks, we perform modeling using volume percentage of a leucogranite and a metasedimenatry rock from study area and REE data of minerals from rhyolite (Nash and Crecraft, 1985) and melanosome of migmatite (Bea et al., 1994). Resultants of modeling indicate that LREE and HREE are controlled by monazites and garnet, respectively, although zircon is estimated HREE dominant in some leucogranite without garnet. Because there are many inclusions of accessary phases such as monazite and zircon in biotites from metasedimentary rocks. leucogranitic magma was mainly derived from muscovite-breakdown in metasedimenary rocks. Leucogranites can be subdivided into two types in compliance with Eu anomaly of chondrite nomalized REE pattern; the one of negative Eu anomaly is type I and the other is type II. Leucogranites have lower Eu concetnrations than that of metasedimenary rocks and similar that of both type. REE modeling suggest that this difference of Eu value is due to that of components of feldspars in both leucogranite and metasedimentary rock. The tendency of major ($K_2O$ and $Na_2O$) and face elements (Eu, Rb, Sr and Ba) of leucogranites also indicate that source magma of these two types was developed by anatexis experienced strong fractionation of alkali-feldspar. Conclusionally, leucogranites in this area are products of melts which was generated by muscovite-breakdown of metasedimenary rock in environment of continetal collision during high temperature/pressure metamorphism and then was fractionated and crystallized after extraction from source rock.

• International Commerce and Information Review
• /
• v.13 no.4
• /
• pp.177-201
• /
• 2011

Myanmar had fallen behind other southeast asian nations since Burmese way to Socialism settled down. However, historically second election in Myanmar hold in 2011 and dramatic changes in areas such as Special Economic Zone announcement, the very huge inflows of foreign direct investment in a year of 2009, the infrastructure building projects, a permit of the right to strike for Labour Organization in Myanmar etc. Particularly, Foreign investments and trade with neighbouring countries are actively growing and also with Korea. But investments of Korea in Myanmar relatively are not diversity, with limited sectors such as mining and sewing manufacturing. In this point of view, this paper is trying to make implications for strategies of entry and investments of Korea in Myanmar by using previous papers related to Myanmar economies, trade and foreign investments with updated statistical data. The implications for Korea is that recently Myanmar economy is in its early stages of development. Although it can occur huge demand of railway, road, communications and constructions related to social infrastructures essentially needed for development of a country, these sectors relatively need huge investments. On the other hands, textile and sewing industry relatively need smaller investments in which investors can utilize low labour cost and a position for export to third countries. But those firms which set up for those purpose in Myanmar might have trouble creating domestic markets in future. Moreover, due to demand which occur in the early stage of growth in Myanmar, trade volume tend to increase and trading is also possible to invest but Myanmar still have lots of problems with infrastructure such as road and logistics and we need to make pre-survey for the costs and benefits of our products Finally, Myanmar government is trying to promote and encourage some of industries such as export-oriented industry, import substitution industry and labour-intensive industry. It can also means they will accumulate capital which can be sources for Myanmar economic growth.

• Management & Information Systems Review
• /
• v.22
• /
• pp.137-165
• /
• 2007

It seems high time to increase productivity by adopting e-business to overcome challenges posed by both external factors including the appreciation of Korean won, oil hikes and fierce global competition and domestic issues represented by disparities between large corporations and small and medium enterprises (SMEs), Seoul metropolitan and local cities, and export and domestic demand all of which weaken future growth engines in the Korean economy. The demands of the globalization era are for innovative changes in businessprocess and industrial structure aiming for creating new values. To this end, e-business is expected to play a core role in the sophistication of the Korean economy through new values and innovation. In order to examine business performance in e-business-adopting industries, this study analyzed the home shopping industry by closely looking into the financial ratios including the ratio of net profit to sales, the ratio of operation income to sales, the ratio of gross cost to sales cost, the ratio of gross cost to selling, general and administrative (SG&A) expense, and return of investment (ROI). This study, for best outcome, referred to corporate financial statements as a main resource to calculate financial ratios by utilizing Data Analysis, Retrieval and Transfer System (DART) of the Financial Supervisory Service, one of the Korea's financial supervisory authorities. First of all, the result of the trend analysis on the ratio of net profit to sales is as following. CJ Home Shopping has registered a remarkable increase in its ratio of net profit rate to sales since 2002 while its competitors find it hard to catch up with CJ's stunning performances. This is partly due to the efficient management compared to CJ's value of capital. Such significance, if the current trend continues, will make the front-runner assume the largest market share. On the other hand, GS Home Shopping, despite its best organized system and largest value of capital among others, lacks efficiency in management. Second of all, the result of the trend analysis on the ratio of operation income to sales is as following. Both CJ Home Shopping and GS Home Shopping have, until 2004, recorded similar growth trend. However, while CJ Home Shopping's operating income continued to increase in 2005, GS Home Shopping observed its operating income declining which resulted in the increasing income gap with CJ Home Shopping. While CJ Home Shopping with the largest market share in home shopping industryis engaged in aggressive marketing, GS Home Shopping due to its stability-driven management strategies falls behind CJ again in the ratio of operation income to sales in spite of its favorable management environment including its large capital. Companies in the Group B were established in the same year of 2001. NS Home Shopping was the first in the Group B to shift its loss to profit. Woori Home Shopping has continued to post operating loss for three consecutive years and finally was sold to Lotte Group in 2007, but since then, has registered a continuing increase in net income on sales. Third of all, the result of the trend analysis on the ratio of gross cost to sales cost is as following. Since home shopping falls into sales business, its cost of sales is much lower than that of other types of business such as manufacturing industry. Since 2002 in gross costs including cost of sales, SG&A expense, and non-operating expense, cost of sales turned out to have remarkably decreased. Group B has also posted a notable decline in the same sector since 2002. Fourth of all, the result of the trend analysis on the ratio of gross cost to SG&A expense is as following. Due to its unique characteristics, the home shopping industry usually posts ahigh ratio of SG&A expense. However, more than 80% of SG&A expense means the result of lax management and at the same time, a sharp lower net income on sales than other industries. Last but not least, the result of the trend analysis on ROI is as following. As for CJ Home Shopping, the curve of ROI looks similar to that of its investment on fixed assets. As it turned out, the company's ratio of fixed assets to operating income skyrocketed in 2004 and 2005. As far as GS Home Shopping is concerned, its fixed assets are not as much as that of CJ Home Shopping. Consequently, competition in the home shopping industry, at the moment, is among CJ, GS, Hyundai, NS and Woori Home Shoppings, and all of them need to more thoroughly manage their costs. In order for the late-comers of Group B and other home shopping companies to advance further, the current lax management should be reformed particularly on their SG&A expense sector. Provided that the total sales volume in the Internet shopping sector is projected to grow over 20 trillion won by the year 2010, it is concluded that all the participants in the home shopping industry should put strategies on efficient management on costs and expenses as their top priority rather than increase revenues, if they hope to grow even further after 2007.

• Tuberculosis and Respiratory Diseases
• /
• v.44 no.3
• /
• pp.574-582
• /
• 1997

Background : Normal humans meet the increased ventilatory need during exercise initially by the increase of tidal volume (TV) and later by the increase of respiratory frequency (Rf). And the inspiratory duty cycle (Ti/Ttot) is also increased more than 50% for the compensation of the decrease of respiratory cycle provoked by the increase of respiratory frequency. The patients with chronic airflow obstruction show rapid and shallow breathing pattern during exercise because of the decreased ventilatory capacity and the increased dead space ventilation. However, the studies about the change of inspiratory duty cycle are only a few and there is no literature about the relationship between the change of inspiratory duty cycle and the degree of airflow obstruction. Methods : The subjects were the twelve patients with chronic airflow obstruction (CAO) and ten normal people. The incremental exercise test was done. The increase of work load was 10 W in CAO group and 25 W in normal control group. The analysis of the results was done by the comparison of the parameters such as minute ventilation (VE), TV, Rf, physiologic dead space (Vd/Vt), and inspiratory duty cycle between the two groups. Each parameters were compared after transformation into % control duration base that means dividing the total exercise time into five fractions and % control duration data were obtained at rest, 20%, 40%, 60%, 80%, and max. Statistical analysis was done by repeated measure ANOVA using SAS program. Results : The changes of VE and TV were significantly different between two groups while the change of Rf was not significant. The decrease of Vd/Vt was significantly low in CAO group. Ti/Ttot was markedly increased from 38.4 + 3.0% at rest to 48.6 + 4.5% at max in normal control group while Ti/Ttot showed little change from 40.5 + 2.2% at rest to 42.6 + 3.5% at max. And the change of inspiratory duty cycle showed highly good correlation with the degree of airflow obstruction (FEV1%). (r=0.8151, p < 0.05). Conclusions : The increase of Ti/Ttot during exercise observed in normal humans is absent in the patients with CAO and the change of Ti/Ttot is well correlated with the degree of airflow obstruction.

• Food Science and Preservation
• /
• v.23 no.7
• /
• pp.1065-1073
• /
• 2016

This study investigated the sensory attributes and quality characteristics of Fuji apples based on market commodity price to provide data for quality index of Fuji apples. Samples were purchased from the Garak market (Seoul Agro-Fisheries & Food Corporation) and divided into four groups depending on the price such as group A, B, C, D. There were no significant differences in their volume and weight among groups. In the soluble solid content and total free sugar, A and B group (high price) showed higher content than those of C and D (low price) group. And also, the A group and B, C, D group showed 386.29 mg% and 320.09~359.28 mg% in the total organic acid content, respectively. As an sensory evaluation results, A group and B group were evaluated higher score than those of C and D group in the uniformity of red color and glossiness of skin and unique apple sensory attributes using quantitative descriptive analysis. Consumer test showed similar to quantitative descriptive analysis results in the various sensory attributes. In the analysis results between quality characteristics and sensory attributes of Fuji apples, total acceptability was correlated positively with titratable acidity (r=0.58), soluble solid (r=0.89), soluble solid content/titratable acidity ratio (r=0.42), total free sugar (r=0.36) and total organic acid (r=0.38). Based on principal component analysis of apple's quality characteristics, apples were primary separated along the first principal component (pH, acidity, soluble solid content, total free sugar, organic acid), which accounted for 66.01% of total variance. In addition, principal component analysis of sensory evaluation revealed a total variance for the quantitative descriptive of 55. 65% and a total variance for the consumer test of 55.84%.

• Economic and Environmental Geology
• /
• v.46 no.1
• /
• pp.11-19
• /
• 2013

The Daehwa Mo-W deposit is located within the Gyeonggi massif. Quartz and calcite vein mineralization occurred in the Precambrian gneiss and Jurassic granites. Three main types (Type I: liquid-rich $H_2O$ type, Type II: vapor-rich $H_2O$ type, Type III: $CO_2-H_2O$ type) of fluid inclusions were observed and are classified herein based on their phase relations at room temperature. Within ore shoots, type III fluid inclusions have been classified into four subtypes (type IIIa, IIIb, IIIc and IIId) based on their volume percent of aqueous and carbonaceous ($CO_2$) phase at room temperatures combined with their total homogenization behavior and homogenization behavior of $CO_2$ phase. Homogenization temperatures of primary type I fluid inclusions in the quartz range from $374^{\circ}C$ to $161^{\circ}C$ with salinities between 13.6 and 0.5 equiv. wt.% NaCl. Homogenization temperatures of primary type III fluid inclusions in quartz of main generation, are in the range of $303^{\circ}C$ to $251^{\circ}C$. Clathrate melting temperatures of the type III fluid inclusions were 7.3 to $9.5^{\circ}C$, corresponding to salinities of 5.2 to 1.0 equiv. wt. % NaCl. Melting and homogenization temperatures of $CO_2$ phase of type III fluid inclusions were -57.4 to $-56.6^{\circ}C$ and 29.0 to $30.8^{\circ}C$, respectively. Fluid inclusion data indicate a complex geochemical evolution of hydrothermal fluids. The Daehwa early hydrothermal system is characterized by $H_2O-CO_2$-NaCl fluid at about $400^{\circ}C$. The main mineralization occurred by $CO_2$ immiscibility at temperatures of about 300 to $250^{\circ}C$. At the late base-metal mineralization aqueous fluid formed by mixing with cooler and less saline meteoric groundwater.

• Journal of Intelligence and Information Systems
• /
• v.16 no.3
• /
• pp.163-179
• /
• 2010

Recentlythe concept of fast fashion is drawing attention as customer needs are diversified and supply lead time is getting shorter in fashion industry. It is emphasized as one of the critical success factors in the fashion industry how quickly and efficiently to satisfy the customer needs as the competition has intensified. Because the fast fashion is inherently susceptible to trend, it is very important for fashion retailers to make quick decisions regarding items to launch, quantity based on demand prediction, and the time to respond. Also the planning decisions must be executed through the business processes of procurement, production, and logistics in real time. In order to adapt to this trend, the fashion industry urgently needs supports from intelligent quick response(QR) system. However, the traditional functions of QR systems have not been able to completely satisfy such demands of the fast fashion industry. This paper proposes an intelligent quick response system for the fast fashion(IQRS-FF). Presented are models for QR process, QR principles and execution, and QR quantity and timing computation. IQRS-FF models support the decision makers by providing useful information with automated and rule-based algorithms. If the predefined conditions of a rule are satisfied, the actions defined in the rule are automatically taken or informed to the decision makers. In IQRS-FF, QRdecisions are made in two stages: pre-season and in-season. In pre-season, firstly master demand prediction is performed based on the macro level analysis such as local and global economy, fashion trends and competitors. The prediction proceeds to the master production and procurement planning. Checking availability and delivery of materials for production, decision makers must make reservations or request procurements. For the outsourcing materials, they must check the availability and capacity of partners. By the master plans, the performance of the QR during the in-season is greatly enhanced and the decision to select the QR items is made fully considering the availability of materials in warehouse as well as partners' capacity. During in-season, the decision makers must find the right time to QR as the actual sales occur in stores. Then they are to decide items to QRbased not only on the qualitative criteria such as opinions from sales persons but also on the quantitative criteria such as sales volume, the recent sales trend, inventory level, the remaining period, the forecast for the remaining period, and competitors' performance. To calculate QR quantity in IQRS-FF, two calculation methods are designed: QR Index based calculation and attribute similarity based calculation using demographic cluster. In the early period of a new season, the attribute similarity based QR amount calculation is better used because there are not enough historical sales data. By analyzing sales trends of the categories or items that have similar attributes, QR quantity can be computed. On the other hand, in case of having enough information to analyze the sales trends or forecasting, the QR Index based calculation method can be used. Having defined the models for decision making for QR, we design KPIs(Key Performance Indicators) to test the reliability of the models in critical decision makings: the difference of sales volumebetween QR items and non-QR items; the accuracy rate of QR the lead-time spent on QR decision-making. To verify the effectiveness and practicality of the proposed models, a case study has been performed for a representative fashion company which recently developed and launched the IQRS-FF. The case study shows that the average sales rateof QR items increased by 15%, the differences in sales rate between QR items and non-QR items increased by 10%, the QR accuracy was 70%, the lead time for QR dramatically decreased from 120 hours to 8 hours.