• Journal of the Korean Geotechnical Society
• /
• v.33 no.7
• /
• pp.43-53
• /
• 2017

Road subsidence, frequently occurring in urban areas, is caused by collapsing of surface layer due to underground cavities followed by a loss of soils. To better understand this phenomenon, the mechanism of cavity formation should be identified firstly. Two kinds of possible subsidence mechanisms were established through previous case studies and the numerical analyses based on Distinct Element Method were conducted for each of these mechanisms. It was confirmed that particle loss and surface settlement can develop differently depending on slit size, void ratio, and particle shape among the various factors influencing the road subsidence. The result demonstrated that the effects of varying cavity diameter and depth could be quantified as a damage chart.

• Journal of Welding and Joining
• /
• v.7 no.2
• /
• pp.35-48
• /
• 1989

This study is concerned with a correlation of microstructure and local brittle zone (LBZ) in offshore structural steel welds. The influence of the LBZ on fracture toughness was investigated by means of simulated heat-affected zone (HAZ) tests as well as welded joint tests. Micromechanical processes involved in void and cleavage microcrack formation were also identified using notched round tensile tests and subsequent SEM observations. The LBZ in the HAZ of a multiphase welded joint is the interstitially reheated coarse grained HAZ, which is influenced by metallurgical factors such as effective grain size, the major matrix structure and the amount of high-carbon martensite-austenite (M-A) constituents. The experimental results indicate that Chirpy energy was found to scale monotonically with the amount of M-A constituents, confirming that the M-A constituent is the major microstructural factor controlling the HAZ toughness. In addition, voids and microcracks are observed to initiate at M-A constituents by the shear cracking process. Thus, the M-A constituent played an important role in initiating the voids and microcracks, and consequently caused brittle fracture.

• Korean Journal of Metals and Materials
• /
• v.47 no.7
• /
• pp.397-405
• /
• 2009

The high strain rate deformation behavior of ultra-fine grained 5083 aluminum alloys prepared via equal channel angular (ECA) extrusion was investigated in this study. The microstructure of ECA extruded specimens consisted of ultra-fine grains, and contained a considerable amount of second phase particles, which were fragmented and distributed homogeneously in the matrix. According to the dynamic torsion test results, the maximum shear stress and fracture shear strain of the route A (no rotation) specimen were lower than those of route C ($180^{\circ}$ rotation) specimen since that adiabatic shear bands of $100{\mu}m$ in width were formed in the route A specimen. The formation of adiabatic shear bands was addressed by concepts of critical shear strain, deformation energy required for void initiation, and microstructural homogeneity associated with ECA operations.

• Korean Journal of Optics and Photonics
• /
• v.1 no.1
• /
• pp.73-86
• /
• 1990

The technique of Spectroscopic Ellipsometry (SE) has been examined with emphasis on its inherent sensitivity to the existence of thin films or surface equivalents. A brief review of related theories like the Fresnel reflection coefficients, the effect of a multilayer upon reflectivities, together with the validity of the effective medium theory and the modelling procedure, is followed by a short description of the experimental setup of a rotating polarizer type SE as well as the necessful expressions which lead to tan and cos. Out of its numerous, successful applications, a few are exampled to convince a reader that SE can be applied to a variety of research fields related to surface, interface and thin films. Specifically, those are adsorption and/or desorption on metals or semiconductors, oxidation process, formation of passivation layers on an electrode, thickness determination, interface between semiconductor and its oxide, semiconductor heterojunctions, surface microroughness, void distribution of dielectric, optical thin films, depth profile of multilayered samples, in-situ or in-vitro characterization of a solid surface immersed in electrolyte during electrochemical, chemical, or biological treatments, and so on. It is expected that the potential capability of SE will be widely utilized in a very near future, taking advantage of its sensitivity to thin films or surface equivalents, and its nondestructive, nonperturbing characteristics.

• Geomechanics and Engineering
• /
• v.18 no.3
• /
• pp.267-275
• /
• 2019

Tabriz is a large Iranian city and the capital of the East Azerbaijan province. The bed rock of this city is mainly consisted of marl layers. Marl layers have some outcrops in the northern and eastern parts of city that mainly belong to the Baghmisheh formation. Based on their colors, these marls are classified into three types: yellow, green, and gray marls. The city is developing toward its eastern side wherein various civil projects are under construction including tunnels, underground excavation, and high-rise building. In this regard, the swelling behavior assessment of these marls is of critical importance. Also, in lightweight structures with foundation pressure less than swelling pressure, several problems such as walls cracking and jamming of door and windows may occur. In the present study, physical properties and swelling behavior of Baghmisheh marls are investigated. According to the X-ray diffractometer (XRD) results, the marls are mainly composed of Illite, Kaolinite, Montmorillonite, and Chloride minerals. Type and content of clay minerals and initial void ratio have a decisive role in swelling behavior of these marls. The swelling potential of these marls was investigated using one-dimensional odometer apparatus under stress level up to 10 kPa. The results showed that yellow marls have high swelling potential and expansibility compared to the other marls. In addition, green and gray marls showed intermediate and low swelling potential and swelling pressure, respectively.

• Steel and Composite Structures
• /
• v.31 no.2
• /
• pp.113-123
• /
• 2019

In this study, carbon fiber/epoxy (CF/EP) composites were interleaved with aramid nonwoven veils with an areal weight density of $8.5g/m^2$ to improve their Mode-I fracture toughness. The control and aramid interleaved CF/EP composite laminates were manufactured by VARTM in a [0]4 configuration. Tensile, three-point bending, compression, interlaminar shear, Charpy impact and Mode-I (DCB) fracture toughness values were determined to evaluate the effects of aramid nonwoven fabrics on the mechanical performance of the CF/EP composites. Thermomechanical behavior of the specimens was investigated by Dynamic Mechanical Analysis (DMA). The results showed that the propagation Mode-I fracture toughness values of CF/EP composites can be significantly improved (by about 72%) using aramid nonwoven fabrics. It was found that the main extrinsic toughening mechanism is aramid microfiber bridging acting behind the crack-tip. The incorporation of these nonwovens also increased interlaminar shear and Charpy impact strength by 10 and 16.5%, respectively. Moreover, it was revealed that the damping ability of the composites increased with the incorporation of aramid nonwoven fabrics in the interlaminar region of composites. On the other hand, they caused a reduction in in-plane mechanical properties due to the reduced carbon fiber volume fraction, increased thickness and void formation in the composites.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.19 no.1
• /
• pp.51-58
• /
• 2021

Chemical decontamination of primary systems in a nuclear power plant (NPP) prior to commencing the main decommissioning activities is required to reduce radiation exposure during its process. The entire process is repeated until the desired decontamination factor is obtained. To achieve improved decontamination factors over a shorter time with fewer cycles, the appropriate flow characteristics are required. In addition, to prepare an operating procedure that is adaptable to various conditions and situations, the transient analysis results would be required for operator action and system impact assessment. In this study, the flow characteristics in the steady-state and transient conditions for the chemical decontamination operations of the Kori-1 NPP were analyzed and compared via the MARS-KS code simulation. Loss of residual heat removal (RHR) and steam generator tube rupture (SGTR) simulations were conducted for the postulated abnormal events. Loss of RHR results showed the reactor coolant system (RCS) temperature increase, which can damage the reactor coolant pump (RCP)s by its cavitation. The SGTR results indicated a void formation in the RCS interior by the decrease in pressurizer (PZR) pressure, which can cause surface exposure and tripping of the RCPs unless proper actions are taken before the required pressure limit is achieved.

• Geomechanics and Engineering
• /
• v.28 no.3
• /
• pp.239-253
• /
• 2022

Suitable techniques to stabilize organic soil and improve its engineering behaviour are in demand. Despite various alternatives, nano-additives proved to be an effective stabilizer owing to their strength enhancing properties. The study focuses on using nano-silica as a potential stabilizer to improve organic silt. Soil was treated with four dosages of nano-silica namely 0.2%, 0.4%, 0.6% and 0.8% of dry weight of the soil. Nano-silica treated soil showed a strength increase of nearly 25% at a dosage of 0.4% after curing for two hours. Strength of the treated soil improved with age. Strength improved by nearly 62.9% after 28 days of curing and 221.4% after 180 days of curing due to formation of Calcium - Silicate - Hydrate (CSH) gel in the soil matrix. Dosage of 0.6% nano-silica is observed to be the optimum dosage. Coefficient of permeability and compression index showed an increase by 13.32 and 5.5 times respectively owing to aggregation of particles and creation of void spaces as visualized from the scanning electron micrographs. Further model foundation study and numerical parametric studies using PLAXIS 2D indicate that optimized and economic results can be obtained by varying the additive dosage with depth.

• Journal of the Korea Concrete Institute
• /
• v.22 no.3
• /
• pp.287-295
• /
• 2010

In this study, ordinary Portland cement was used and the air void was minimized by using minute quartz as the filler. In addition, steel fibers were used to mitigate the brittle failure problem associated with high strength concrete. This study is in progress to make an Ultra-high strength powdered concrete (UHSPC) which has compressive strength over 300 MPa. To increase the strength of concrete, we have compared and analyzed the compressive strengths of the concretes with different mix proportions and curing conditions by selecting quartz sand, dolomite, bauxite, ferro silicon which have diameters less than 0.6 mm and can increase the bond strength of the transition zone. Ultra-high strength powdered concrete, which is different from conventional concrete, is highly influenced by the materials in the mix. In the study, the highest compressive strength of the powdered concrete was obtained when it is prepared with ferro silicon, followed in order by Bauxite, Dolomite, and Quartz sand. The amount of ferro silicon, when the highest strength was obtained, was 110%, of the weight of the cement. SEM analysis of the UHSPC showed that significant formation of C-S-H and Tobermorite due to high temperature and pressure curing. Production of Ultrahigh strength powdered concrete which has 28-day compressive strength upto 341MPa has been successfully achieved by the following factors; steel fiber reinforcement, fine particled aggregates, and the filling powder to minimize the void space, and the reactive materials.

• Journal of the Korea Concrete Institute
• /
• v.14 no.5
• /
• pp.742-749
• /
• 2002

This study was performed to clarify the formation procedure of continuous voids in cellular concrete, and to examine the effect of a foaming agent on the manufacture of cellular concrete with continuous voids. By the experiments, it was determined that cellular concrete to be formed with continuous voids is influenced by temperature, viscosity and flowability of cement paste, and stability of air voids, and is formed in accordance with cohesion of air voids. It was also found that separate voids are formed at an added amount of air voids corresponding to 2 ％ or less of the amount of cement, whereas an antifoaming phenomenon occurs when the added amount of air voids exceeds 9 ％ of the amount of cement. In products with respective cement fineness of 3,000, 6,000, and 8,000㎠/g, a higher compressive strength was exhibited at a higher cement fineness. The continuous void ratio depending on a variation in fineness was 38 ％, 52 ％, and 22 ％ in those products, respectively. That is, a highest continuous void ratio was exhibited at a cement fineness of 6,000㎠/g. When the water-cement ratio was reduced from 45％ to 25％, the compressive strength of the cellular concrete was increased from 15 kgf/㎠ to 20 kgf/㎠ Thus, the reduction in water-cement ratio was effective in achieving an increase in strength without any variation in the specific gravity of the cellular concrete.