• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.1
• /
• pp.46-50
• /
• 1990

Heteroface AlGaAs/GaAs drift solar cells with an active area conversion efficiency of 15.9% under one sun and AM 1.5 condition have been grown by molecular beam epitaxy(MBE). These drift solar cells have graded doping profiles in the base and emitter regions. The cells have a short circuit current density (Jsc) of 19.00 mA/cm\ulcorner an open circuit voltage(Voc) of 0.93 V, and f fill factor(FF) of 0.78, respectively. Conventional solar cells with fixed doping profiles were also grown by MBE for comparison with the drift solar cells. Even though the fabrication cost of MBE grown solar cell is higher, the expected highest conversion efficiency of the single or multiple cells could compensate for the increased cost, particularly in case of space applications.

• Journal of Ceramic Processing Research
• /
• v.13 no.spc2
• /
• pp.336-340
• /
• 2012

Wide band gap p-type hydrogenated amorphous silicon oxide (a-SiO:H) buffer layer has been used at the interface of transparent conductive oxide (TCO) and hydrogenated amorphous silicon (a-Si:H) p-type layer of a p-i-n type a-Si:H solar cell. Introduction of 5 nm thick buffer layer improves in blue response of the cell along with 0.5% enhancement of photovoltaic conversion efficiency (η). The cells with buffer layer show higher open circuit voltage (Voc), fill factor (FF), short circuit current density (Jsc) and improved blue response with respect to the cell without buffer layer.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.23 no.1
• /
• pp.50-57
• /
• 1986

The fabricatoin sequence of GaAs MIS type diode and its electrical characteristics are presented. Used wafers were undoped GaAS wafer adn Te-doped GaAs wafer. Au and AuGe/Ni was used as schottky contact metal and ohmic contact metal respectively. Oxide layer on GaAs surface was formed by water vapor saturated oxide growth technique and dry oxidation technique. In Te-doped GaAs wafer, cutin voltage of MIS type diode was enhanced about 3V comparing with non-oxide layer diode. From light I-V characteristics fill factor of MIS type Te-doped GaAs diode was about 64%, Voc(open circuit voltage) was 0.67V.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.410.2-410.2
• /
• 2016

Tandem structure is promising in organic solar cells because of its double open-circuit voltage (VOC) and efficient photon energy conversion. In a typical tandem device, the two single sub-cells are stacked and connected by an interconnecting layer. The fabrication of two sub-cells are usually carried out in a glovebox filled with nitrogen or argon gas, which makes it expensive and laborious. We report a glovebox-free fabricated inverted tandem organic solar cells wherein the tandem structure comprises sandwiched interconnecting layer based on p-doped hole-transporting, metal, and electron-transporting materials. Complete fabrication process of the tandem device was performed outside the glove box. The tandem solar cells based on poly(3-hexylthiophene) (P3HT) and (6,6)-phenyl C61-butyric acid methyl ester (PCBM) can realize a high VOC, which sums up of the two sub-cells. The tandem device structure was ITO/ZnO/P3HT:PCBM/PEDOT:PSS/MoO3/Au/Al/ZnO-d/P3HT:PCBM/PEDOT:PSS/Ag. The separate sub-cells were morphologically and thermally stable up to 160 oC. The high stability of the active layer benefits in the fabrication processes of tandem device. The performance of tandem organic solar cells comes from the sub-cells with an 50 nm thick active layer of P3HT:PCBM, achieving an average power conversion efficiency (PCE) of 2.9% (n=12) with short-circuit current density (JSC) = 4.26 mA/cm2, VOC = 1.10 V, and fill factor (FF) = 0.62. Based on these findings, we propose a new method to improve the performance and stability of tandem organic solar cells.

• Applied Chemistry for Engineering
• /
• v.21 no.2
• /
• pp.137-141
• /
• 2010

Poly [4,7-Di-thiophen-2-yl-benzo(1,2,5)thiadiazole]-alt-1,4-bis(dodecyloxy)-2,5-divinylbenzene (PPVTBT) was synthesized by the Heck coupling reaction between 4,7-Di-thiophen-2-yl-benzo(1,2,5)thiadiazole and 1,4-bis(dodecyloxy)-2,5-divinylbenzene. The maximum absorption and band gap of PPVTBT were 550 nm and 1.74 eV, respectively. The HOMO and LUMO energy level of PPVTBT were -5.24 eV and -3.50 eV, respectively. The photovoltaic device based on the blend of PPVTBT and (6)-1-(3-(methoxycarbonyl)propyl)-{5}-1-phenyl[5,6]-$C_{61}$ (PCBM) (1 : 6 by weight ratio) was fabricated. The efficiency of device was 0.16%. The short circuit current density (Jsc), fill factor (FF) and open-circuit voltage (Voc) of the device was $0.74mA/cm^{2}$, 31% and 0.71 V, respectively, under AM 1.5 G and 1 sun condition ($100mA/cm^{2}$).

• Current Photovoltaic Research
• /
• v.6 no.2
• /
• pp.56-61
• /
• 2018

In this study, CIGS absorber layers were deposited on low-alkali glass and sodalime glass substrates and potasium floride (KF) of various thicknesses was supplied at an elevated temperature after the CIGS growth. The effect of KF post-deposition treatment on the two types of substrates was extremely different. On the low-alkali substrate, the open-circuit voltage (Voc) was improved but the fill-factor (FF) degradation was severe, whereas the sodalime substrate showed Voc deterioration and FF improvement. In the case of supplying 20 nm of KF on both substrates, the efficiency gain of 0.3~1.1%p was obtained. With increasing the KF thickness, a small protrusion-like microstructure developed on the surface of the absorber layer, and the microstructures that were not removed in the subsequent process were found to be the main cause of the FF loss.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.432.1-432.1
• /
• 2016

We demonstrated that the power conversion efficiency (PCE) of bilayer solar cell was significantly enhanced by inserting interfacial layer between the organic bilayer film and the Al electrode. Moreover, the water contact angle shows that the bilayer solar cells suffer from the undesirable surface component which limits the charge transport to the Al electrode. The AFM measurement has revealed that the pre- and post-thermal annealing treatments results in different morphologies of the interfacial layer which is critical for the higher PCE of the bilayer solar cells. Furthermore we have investigated the electrical properties of the bilayer solar cells and obtained insights into the detailed device mechanisms. The transient photovoltage measurements suggests that the significantly enhanced Voc is caused by reducing the recombination at the interface between the organic films and the Al electrode. By inserting the TiO2 layer between the bilayer film and Al electrode, the open circuit voltage (Voc) was increased from 0.37 to 0.66V. Consequently, the power conversion efficiency (PCE) of bilayer solar cells was significantly enhanced from 1.23% to 3.71%. As the results, the TiO2 interfacial layer can be used to form an ohmic contact layer, serveing as a blocking layer to prevent the penetration of the Al, and to reduce the recombination at the interface.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.426.1-426.1
• /
• 2016

We report high work function Aluminum doped zinc oxide (AZO) films as insertion layer as a function of O2 flow rate between transparent conducting oxides (TCO) and hydrogenated amorphous silicon oxide (a-SiOx:H) layer to improve open circuit voltage (Voc) and fill factor (FF) for high efficiency thin film solar cell. However, amorphous silicon (a-Si:H) solar cells exhibit poor fill factors due to a Schottky barrier like impedance at the interface between a-SiOx:H windows and TCO. The impedance is caused by an increasing mismatch between the work function of TCO and that of p-type a-SiOx:H. In this study, we report on the silicon thin film solar cell by using as insertion layer of O2 reactive AZO films between TCO and p-type a-SiOx:H. Significant efficiency enhancement was demonstrated by using high work-function layers (4.95 eV at O2=2 sccm) for engineering the work function at the key interfaces to raise FF as well as Voc. Therefore, we can be obtained the conversion efficiency of 7 % at 13mA/cm2 of the current density (Jsc) and 63.35 % of FF.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.394-394
• /
• 2009

Water solubility of conjugated polymers may offer many applications. Potential applications of water-soluble conjugated polymers include the polymer light-emitting diode and new materials for nano and micro hollow-capsules, and bio- or chemo-sensors. We synthesized neutral polyfluorenes containing bromo-alkyl groups by the palladium catalyzed Suzuki coupling reaction. Bromo-alkyl side groups in neutral polyfluorenes were quaternized by tri-methyl amine solution. The electrochemical and optical properties of water-soluble conjugated polymers are discussed. This novel synthesized water-soluble conjugated polymers were used as a interfacial dipole layer between active layer and metal cathode in polymer solar cell for enhancement of open-circuit voltage (Voc), which is one of the most critical factors in determining device characteristics. We also investigated the device performance of polymer solar cell with different metal cathode such as Al, Ag, Au and Cu. In polymer solar cell, novel cationic water-soluble conjugated polymers were inserted between active layer and high-work function cathode (Al, Ag, Au and Cu).

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.299-301
• /
• 2007

An organic-inorganic hybrid solar cell fibers with characteristics such as formability, low-cost and tailorability was developed by deposition of C60 and CuPc on fiber surface. In spite of some variation according to the temperature of ITO deposition, the maximum open circuit voltage of 0.39V was attained at $150^{\circ}C$(1000end). The resulting solar cell showed the performances Isc=0.482, Voc=0.320, FF=0.285 ${\eta}_{e}=0.044$% which are comparable to one of other types of solar cells in literature.