• Journal of Biosystems Engineering
• /
• v.37 no.1
• /
• pp.28-35
• /
• 2012

Purpose: This study performed the oscillatory test using the texture analyzer to characterize the viscoelastic behavior of apples such as the storage modulus (E'), the loss modulus (E"), the complex modulus (${\mid}E^*{\mid}$) and the energy dissipated per cycle ($W_{diss}$). Methods: The sinusoidal deformation with the frequency of 1-10 Hz and the maximum displacement of 0.1 mm were applied to the flesh tissues of Fuji, Golden Delicious and Red Delicious apples. The Lissajous figure was used to measure the phase angle(${\delta}$) between stress and strain curve. Results: Trigger force was critical to the measurement of the phase angle. E', E", ${\mid}E^*{\mid}$ and Wdiss were measured using the Lissajous figure and the phase angle. The complex modulus of Golden Delicious apple was significantly lower than those of Fuji apple and Red Delicious apple. Conclusions: Apple flesh was exhibiting more elasticity at low frequency, and more viscosity at high frequency. Dynamic compressive properties of Fuji apple were similar to those of Red Delicious apple but significantly different from those of Golden Delicious apple.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.460-465
• /
• 2008

This paper proposes a new type of MR (magentorheological) fluid based suspension system and applies it to military vehicle for vibration control. The suspension system consists of gas spring and MR damper. The nonlinear behavior of spring characteristics is evaluated with respect to the wheel travel and damping force model due to viscosity and yield stress of MR fluid is derived. Subsequently, a military vehicle of 6WD is adopted for the integration of the MR suspension system and its nonlinear dynamic model is establishes by considering vertical, pitch and roll motion. Then, a sky-hook controller associated with semi-active actuating condition is designed to reduce the vibration. In order to demonstrate the effectiveness of the proposed MR suspension system, computer simulation is undertaken showing vibration control performance such as roll angle and pitch angle evaluated under bump and random road profiles.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.37.2-37.2
• /
• 2011

반도체공정에서 Photo-lithography는 특정 광원을 사용하여 구현하고자 하는 패턴을 기판상에 형성하는 기술이다. 이러한 Photo-lithography 공정에서는 패턴이 형성되어 있는 마스크가 핵심적인 역할을 하며 반도체소자의 전체적인 성능을 결정한다. 이에 따라 Photo-lithography용 마스크에 사용되는 Blank 마스크는 Defect의 최소화 및 우수한 평탄도 등의 조건들이 요구되고 있다. 이러한 Blank 마스크 재료로 광원을 효율적으로 투과시키는 성질이 우수하고 다른 재료에 비해 열팽창계수가 작은 석영기판이 사용되고 있다. 석영 기반의 마스크는 UV Lithography에서 주로 사용되고 있으며 그 밖에 UV-NIL (Nano Imrpint Lithography), EUVL (Extreme Ultra Violet Lithography) 등에도 이용되고 있다. 석영기판을 가공하여 Blank 마스크로 제작하기 위해 석영기판의 Lapping/Polishing 등이 핵심기술이며 현재 일본에서 전량 수입에 의존하고 있어, 이에 대한 연구의 필요성이 절실한 상황이다. 본 연구에서는 Blank 마스크제작을 위한 석영기판의 Polishing 공정에 사용되는 Ceria Slurry의 특성 연구 및 이에 따른 연마평가를 실시하였으며 첨가제의 조건에 따른 pH/Viscosity/Stability 등의 물리적인 특성을 관찰하여 석영기판 Polishing에 효율적인 Ceria slurry의 최적조건을 도출했다. 또한, 조건에 따른 Slurry의 정확한 분석을 위해 Zeta Potential Analyzer를 이용하여 연마입자의 크기 및 Zeta Potential에 대한 평가를 실시한 후 연마제와 석영기판의 Interaction force를 측정하였다. 상기 실험에 의해 얻어진 최적화된 연마 공정 조건하에서 Ceria slurry를 사용하여 연마평가를 실시함으로써 Removal Rate/Roughness 등의 결과를 관찰하였다. 본 연구를 통해 반도체 photo mask 제작을 위한 Ceria slurry의 주요특성을 파악하고 석영기판의 Polishing에 효율적인 조건을 도출함으로써 Lithography 마스크를 효율적으로 제작할 수 있을 것으로 예상된다.

• The Bulletin of The Korean Astronomical Society
• /
• v.39 no.2
• /
• pp.74.2-74.2
• /
• 2014

Magnetohydrodynamics(MHD) dynamo depends on many factors such as viscosity ${\gamma}$, magnetic diffusivity ${\eta}$, magnetic Reynolds number $Re_M$, external driving source, or magnetic Prandtl number $Pr_M$. $Pr_M$, the ratio of ${\gamma}$ to ${\eta}$ (for example, galaxy ${\sim}10^{14}$), plays an important role in small scale dynamo. With the high PrM, conductivity effect becomes very important in small scale regime between the viscous scale ($k_{\gamma}{\sim}Re^{3/4}k_fk_f$:forcing scale) and resistivity scale ($k_{\eta}{\sim}PrM^{1/2}k_{\gamma}$). Since ${\eta}$ is very small, the balance of local energy transport due to the advection term and nonlocal energy transfer decides the magnetic energy spectra. Beyond the viscous scale, the stretched magnetic field (magnetic tension in Lorentz force) transfers the magnetic energy, which is originally from the kinetic energy, back to the kinetic eddies leading to the extension of the viscous scale. This repeated process eventually decides the energy spectrum of the coupled momentum and magnetic induction equation. However, the evolving profile does not follow Kolmogorov's -3/5 law. The spectra of EV (${\sim}k^{-4}$) and EM (${\sim}k^0$ or $k^{-1}$) in high $Pr_M$ have been reported, but our recent simulation results show a little different scaling law ($E_V{\sim}k^{-3}-k^{-4}$, $EM{\sim}k^{-1/2}-k^{-1}$). We show the results and explain the reason.

• Fibers and Polymers
• /
• v.1 no.1
• /
• pp.37-44
• /
• 2000

A finite element method is employed fer a flow analysis of the melt spinning process of a non-circular fiber, a PET(polyethylene terephthalate) filament. The flow field is divided into two regions of die channel and spin-line. A two dimensional analysis is used for the flow within the die channel and a three dimensional analysis fur the flow along the spin-line. The Newtonian fluid is assumed for the PET melt and material properties are considered to be constant except for the viscosity. Effects of gravitation, air drag force, and surface tension are neglected. Although the spin-line length is 4.5 m only five millimeters from the spinneret are evaluated as the domain of the analysis. Isothermal and non-isothermal cases are studied fer the flow within the die channel. The relationship between the mass flow rate and the pressure gradient is presented for the two cases. Three dimensional flow along the spin-line is obtained by assuming isothermal conditions. It is shown that changes in velocity and cross-sectional shape occur mostly in the region of 1mm from the die exit.

• Journal of the Korean Ceramic Society
• /
• v.56 no.2
• /
• pp.167-172
• /
• 2019

Silicate glasses with varying SiO₂ and Na₂O contents were prepared and their viscous flow property at the elevated temperature was studied. When the glass powders were packed and sintered at 550℃ to examine their feasibility as a low sintering temperature glass frit, contrary to expectations, glasses with lower SiO₂ content than 60 mol% showed no vitrification after sintering. High temperature microscopy revealed the viscous flow change of the silicate glasses with varying temperature and duration time and also indicated that the viscous flow was limited at low SiO₂ content. X-ray diffraction (XRD) on the sintered samples and Raman spectroscopy were carried out to shed light on the compositional dependency of viscous flow of silicate glasses.

• Journal of Drive and Control
• /
• v.16 no.4
• /
• pp.87-92
• /
• 2019

Rotary dampers are damping devices which provide high resistance to shaft rotation. Rotary dampers are being used in various areas to enable the gentle opening and closing of the rotation motion relative to home furniture, industry machinery and automotive parts. Rotary dampers can be installed directly at the rotating point of a various part and can achieve uniform, gentle movement which increases quality and value of products. And generally, the silicone fluid is used as the damping medium because of its stable viscous properties. The movement of these little decelerators can be achieved with a high viscosity of working fluid and throttles installed in the body of the rotary damper. The damping force can be achieved clockwise, anti-clockwise or in both directions according to the structure of the orifices or throttles. In this paper, the torque performances of the rotary damper containing air in the working fluid were studied. For this purpose, the torque characteristic of the rotary damper according to the variation of various operating conditions such as clearance of leakage, dimensions of groove orifice, content ratio of air, etc., were simulated with AMEsim software.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.6
• /
• pp.1509-1514
• /
• 1990

To investigate the seal dynamic instability for a misaligned and coned mechanical face seal, the finite difference approximation was employed to solve the modified Reynolds equation for an incompressible fluid and temperature dependent viscosity. Using the solution, the results for axial force, transverse moment, restoring moment, and ratio of the transverse moment and the restoring moment are calculated for the whole range from zero to full angular misalignment. The results indicate that the transverse moment due to the angular misalignment and coning terms affects considerably the dynamic instability of face seals. It is shown that the simplified treatment of Reynolds equation using the narrow seal approximation overestimate the ratio of the transverse moment to the restoring moment especially at touch.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.11 no.4
• /
• pp.13-21
• /
• 2001

Electrorheological(ER) fluid is a kind of smart material with variable shear stress and dynamic viscosity under various electric field intensity. Electric field can control the damping characteristics of ER damper. The objective of this study is the analysis of the performance of ER damper and its application to shock absorber. Idealized nonlinear Bingham plastic shear flow model is used to predict the velocity profile between electrodes. Cylindrical dashpot ER damper with moving electrode is constructed and tested under various electric fields. The analytic and experimental results for damping force are compared and discussed. Drop test system using ER damper is prepared to identify transient vibration characteristics. The rebound is eased as the applied electric field increases. When semi-active control algorithm is applied, rebound phenomenon disappears and vibration energy level decays faster than the case of zero electric field.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1939-1943
• /
• 2008

Deformation of a mold is measured and analyzed in alignment and curing processes of UV-Imprint Lithography. We are focused on mold deformation caused by a UV resin, which is laminated between a mold and a target glass-panel. The UV resin is viscous in case of liquid state, and the resin will be solidified when being exposed by the ultra-violet light. The viscosity of the resin causes shear force on the mold during the alignment process. Moreover, the shrinkage during phase change from liquid to solid may cause residual stress on the mold. The experiments for measuring temperature and strain are made during alignment and curing process. Strain-gages and thermocouples are used for measuring the strain and variation of temperature on several points of the mold, respectively. The deformation of mold is also simulated and analyzed. The simulation results are compared with the experiments. Finally, sources of alignment errors in large area UV-nanoimprint lithography are discussed.