• 한국재료학회지
• /
• 제31권2호
• /
• pp.101-107
• /
• 2021

Pores produced by carbonization in bulk graphite process degrade the mechanical and electrical properties of bulk graphite. Therefore, the pores of bulk graphite must be reduced and an impregnation process needs to be performed for this reason. In this study, bulk graphite is impregnated by varying the viscosity of the impregnant. The pore volume and pore size distribution, according to the viscosity of the impregnant, are analyzed using a porosimeter. The total pore volume of bulk graphite is analyzed from the cumulative amount of mercury penetrated. The volume for a specific pore size is interpreted as the amount of mercury penetrating into that pore size. This decreases the cumulative amount of mercury penetrating into the recarbonized bulk graphite after impregnation because the viscosity of the impregnant is lower. The cumulative amount of mercury penetrating into bulk graphite before impregnation and after three times of impregnation with 5.1cP are 0.144 mL/g and 0.125 mL/gm, respectively. Therefore, it is confirmed that the impregnant filled the pores of the bulk graphite well. In this study, the impregnant with 5.1 cP, which is the lowest viscosity, shows the best effect for reducing the total pore volume. In addition, it is confirmed by Raman analysis that the impregnant is filled inside the pores. It is confirmed that phenolic resin, the impregnant, exists inside the pores through micro-Raman analysis from the inside of the pore to the outside.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.95-96
• /
• 2002

The operation of proceeding bearing in the conditions of misaligned axis of proceeding and bush leads to the load concentration on the bearing edges causing further mixed lubrication conditions, unstable operation and intensive wear of mating parts. For the design process of proceeding bearing the knowledge of static characteristics determined from the oil film pressure and temperature distribution is very important. For the 3-lobe proceeding bearing, the pressure, temperature and viscosity fields, load capacity, minimum oil film thickness, power loss, oil flow and maximum oil film temperature have been determined by iterative solution of the Reynolds', energy and viscosity equations. The paper introduces the results of theoretical investigations of static characteristics of 3-lobe proceeding bearing operating at misaligned axis of proceeding and bush. An effect of misalignment ratio, length to diameter ratio of the proceeding bearing, the lobe clearance ratio on the static characteristics was investigated. Laminar, adiabatic model of oil film for the solution of Reynolds, energy and viscosity equations was applied.

• 한국식품영양과학회지
• /
• 제30권3호
• /
• pp.450-454
• /
• 2001

The physical properties of ramyon made of potato starch at various levels (12, 14 16%) were investigated to find out the effect of potato starch on ramyon quality. The higher starch content in dough, the higher water content after steaming and the lower moisture content after deep frying. As the starch content increased, the magnitudes of extrusion work of cooked ramyon and capillary viscosity of ramyon soup increased but the starting temperature of gelatinization decreased. There was a good correlation ($R^2$=0.99) between extrusion work and capillary viscosity. Firmness and chewiness values measured by texture analyser decreased with increase in starch content while tenderness and overall texture preference evaluated by sensory analysis increased.

• International Journal of Concrete Structures and Materials
• /
• 제6권1호
• /
• pp.59-64
• /
• 2012

Sand-concrete is being researched for potential usage in construction in Saharan regions of Algeria, because of shortage in coarse aggregate resources. This research work deals with the effect of dune sand, available in huge quantities in these regions, on the properties of flowing sand-concrete (FSC) prepared with different proportions of dune and river sands. Mini-cone slump test, v-funnel flow-time test and viscosity measurements were used to characterize the behaviour of FSC in fresh state. The 28-day compressive strength was also determined. Test results show that an optimal content of dune sand, which makes satisfied fresh and hardened properties of FSC, is obtained. Moreover, the obtained flow index (constant b) calculated by the help of power-law viscosity model is successfully correlated to the experimental results of v-funnel flow time.

• 대한기계학회논문집B
• /
• 제33권12호
• /
• pp.1014-1021
• /
• 2009

A new eddy viscosity equation was formulated from assumption of turbulence length scale equation and specific dissipation ratio equation. Then, a set of turbulence model equations for the turbulent kinetic energy ${\kappa}$, the viscosity ${\nu}_t$, and the intermittency factor ${\gamma}$ is proposed by considering the entrainment effect. Closure coefficients are determined by experimental data and resorting to numerical optimization. Present model has been applied to compute four representative cases of free shear flows and successfully compared with experimental data. In particular, the spreading rate, the centreline mean velocity and the profiles of intermittency are calculated with improved accuracy. Also, the proposed ${\nu}_t-{\kappa}-{\gamma}$ model was applied to channel flow by considering the wall effect and the results show good agreements with the Direct Numerical Simulation data.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1997년도 제26회 추계학술대회
• /
• pp.86-92
• /
• 1997

When Lubricants is used under severe running condition, tribological characteristics is very important. I have studied the lubricating oil viscosity, kinds of additives and lubricating oil temperatures were changed. In order to study the effect of oil temperature on the wear of the surface, the temperature of the oil was changed for the same sample. Moreover, the temperatures of three kinds of oils which have very different viscosities at room temperature, were varied while the oil viscosity was unchanged. It was shown from the test results that wear is not greatly affected by the amount of ZnDTP antiwear agent, but E-P additives are less effective against wear than ZnDTP additives. The viscosity of lubricating oil and its tempea-ature greatly affect the wear of the surface. Combining all the wear data with those of the surface strength, it was observed that the higher the load, the lower the scratch of wear, and also in the case of the same running load, the lower the wear, the longer the life of the surface strength.

• 대한기계학회논문집B
• /
• 제27권9호
• /
• pp.1327-1334
• /
• 2003

Flow characteristics of the fluid laden with many particles in the two-dimensional channel are investigated using the Navier-Stokes equations coupled with the equation of motion of particles by direct numerical simulation. A four-step fractional step method with Crank-Nicolson scheme and ALE technique is used for P2P1 mixed finite element method. The motion and distribution of particles in the fluid is virtually described as a result of direct numerical simulation and the increase of viscosity is compared with theoretical equations. The effect of channel height on the relative viscosity and the tubular pinch effect are discussed.

• 한국농촌생활과학회지
• /
• 제8권2호
• /
• pp.125-129
• /
• 1997

The effect of mugwort powder on some physicochemical properties of rice flour, the viscosity of rice flour pastes and the degree of gelatinization of pastes and gels were investigated. By addition of mugwort, water binding capacity, swelling power, and solubility of rice flour were increased, also the viscosity and, the degree of gelatinization of rice flour pastes and gels were increased. Generally wet rice flour-mugwort pastes and gels were better than those of dry rice flour-mugwort. And viscosity and gelatinization of the rice-mugwort pastes and gels were decreased slightly during storage at $20^{\circ}C$ for 7 days.

• 한국응용과학기술학회지
• /
• 제27권2호
• /
• pp.99-106
• /
• 2010

We have investigated the rheological behaviours of emulsions containing polymers. The polymers used in this study were polyacrylamide and carboxy vinyl polymer. The emulsion with polyacrylamide shows better prior preference than that with carboxy vinyl polymer on the skin texture. In the toxicity test, such as, LLNA cell toxicity, skin organ culture and human patch test, polyacrylamide was the appropriate materials for the cosmetics. The viscosity of polyacrylamide shows maximum value in neutral pH and good stability against temperature. The decreasing effect of viscosity against salt was not good enough but showed a better result than that of carboxy vinyl polymer. Two times the amount of polyacrylamide should be used for the formation of a similar viscosity of carboxy vinyl polymer. Yield value of polyacrylamide was low and the effect for the stabilizing emulsions was also low.

• Bulletin of the Korean Chemical Society
• /
• 제15권5호
• /
• pp.399-404
• /
• 1994

The non-Newtonian viscosities (the specific or intrinsic viscosities) of poly(L-proline) (PLP, $M_v$=19,000 and 32,000) in various mixed-solvent systems like water-propanol and acetic acid-propanol of varying compositions were measured during the reverse mutarotation (Form II ${\rightarrow}$Form I) by the application of external pressure (up to 4.5 psi). The non-Newtonian viscosity effect was found to be larger in acetic acid-propanol system than in water-propanol system and to somewhat decrease during the reverse mutarotation at a given solvent system. The non-Newtonian viscosity behavior of PLP in aqueous salt ($CaCl_2$) solution was also studied, from which it was found that the degree of the non-Newtonian effect decreased with increasing salt concentration, and increased with increasing PLP molecular weight. These findings could be explained in terms of conformational changes of PLP in solution (like the helix-helix or helix-coil transition) involved.