• Korean Journal of Crystallography
• /
• v.9 no.1
• /
• pp.64-70
• /
• 1998

Porous body was prepared from coal fly ash 70 wt%0clay 30 wt% slip using DCC(Direct Coagulated Casting) method. Effect of the specific gravity of the slip on the pore size and distribution of the sintered body was examined by the SEM observation of microstructure and mercury porosimetry measurement of the pore size distribution. Average pore size of the porous sintered body was about 2.5μm for all slips with specific gravity of 1.55, 1.60 and 1.65g/cm3, respectively. Sintered body prepared from the slip of specific gravity of 1.60g/cm3 have the narrowest pore size distribution. slip of specific gravity of 1.55g/cm3 shows broader pore size distribution due to slow gellation process. Slip of specific gravity of 1.65g/cm3 required large amount of deflocculant and showed large variation of the viscosity with addition of coagulant which resulted in very unstable slip properties.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.456-461
• /
• 2017

In this study, the rheological properties of nitromethane gel propellants on nano/micron sized gelling agent are investigated. Silicon dioxide is used as the gellant with 5 wt%, 6.5 wt% and 8 wt% concentration, respectively, where the measurements are conducted under steady-state shear flow conditions using a rotational rheometer. The nitromethane/silicon dioxide gel showed non-Newtonian flow behavior for the entire experimental shear rate ranges. The gel fuels with nano-sized gellant had a slightly higher viscosity than the gel fuels with micron-sized one for low shear rate range. Additionally, it was found that Herschel-Bulkley model can hardly describe the rheological behavior of nitromethane gel propellant, but the NM model(by Teipel and Forter-Barth) is better suited to explain the rheological behavior of nitromethane gel propellant.

• Journal of the Korean Magnetics Society
• /
• v.8 no.5
• /
• pp.275-281
• /
• 1998

Effects of coupling agents on the rheological and magnetic properties of plastic ferrite magnets were investigated. Magnetic powder used was Sr-ferrite, and binder used was polypropylene (PP), and coupling agents used were ${\gamma}$-methacryloxypropyl trimethoxy silane (A174) and isopropyl triisostearoyl titanate (TTS). It was found that the addition of coupling agents to the PP/ferrite system reduced the melt viscosity and increased the magnetic properties considerably, and the treatment with TTS showed greater effect than A174 did. By comparison with that of the untreated one, the apparent viscosities of the mixtures treated with A174 and TTS decreased 23 % and 50%, respectively, at the shear rate of $1280\; sec^{-1}$ . Untreated plastic magnets showed remanent flux density $(B_r)$ of 1.89 kG and maximum energy energy product $(BH_{max})$ of 0.84 MGOe, and A174 treated magnets showed of Br 2.25 Kg and $BH_{max}$ of 1.23 MGOe. TTS treated magnets showed $B_r$ of 2.35 kG and $BH_{max}$ of 1.33 MGOe.

• Korean Journal of Food Science and Technology
• /
• v.31 no.6
• /
• pp.1679-1682
• /
• 1999

This study was carried out to investigate the effect of hot taste of red pepper seed (RPS) extracts in terms of mixing ratio with red pepper powder (RPP) extracts. As the mixing ratio of RPP extracts to RPS extracts increased, the solid yield, viscosity, turbidity and Hunter a and b values were increased but the L values was decreased. The time-intensity curve from sensory evaluation showed that the hot taste of RPP extracts reached maximum point in short time and decreased fastly while that of RPS slowly developed and maintained the intensity with a little decrease in the tested time. The mixing ratio of RPP and RPS responded the properties of their individual hot taste.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.3
• /
• pp.290-297
• /
• 2016

The absorbent loss due to degradation in $CO_2$ capture process using aqueous alkanol amine solution has adverse effect on the economics of overall process. The degradation causes absorbent loss, equipment corrosion, foaming, adhesive material producing and viscosity increase in operation. In this study, the degradation characteristics of $CO_2$ capture process using MEA (monoehtanolamine) under various conditions such as $O_2$ partial pressure, $CO_2$ loading and absorbent temperature. The effects of iron, which generated from the equipment corrosion, on absorbent degradation were studied using $Fe_2SO_4$ containing MEA solution. The produced gases were analyzed by FT-IR(Fourier Transform Infrared Spectrophotometer) and the specifically measured $NH_3$ concentration was used as a degradation degree of aqueous MEA solution. The experiments showed that the higher $CO_2$ loadings (${\alpha}$), $O_2$ fraction ($y_{O2}$) and reaction temperature enhanced the more degradation of aqueous MEA solution. Comparing other operation parameters, the reaction temperature most affected on the degradation. Therefore, it could be concluded that the above parameters affects on degradation should be considered for the selections of $CO_2$ absorbent and operating conditions.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.277-281
• /
• 2003

Effects of $CaF_2$ addition as a filler on the high frequency dielectric properties and sintering of CaO-$Al_2O_3-SiO_2-B_2O_3$(CASB) and ZnO-MgO-$B_2O_3-SiO_2$(ZMBS) glass composites were investigated. The optimal glass composition in the CASB system was 33.0CaO-$17.0Al_2O_3-35.0SiO_2-15.0B_O_3$(in wt%). The corresponding dielectric properties were k=8.1 and $Q{\times}fo$=1,200GHz. The sintering temperature was $800{\mu}m$. In case of 2MBS system, 25.0ZnO-25.0MgO-20.0$B_2O_3-30.0SiO_2$(in wt%) glass showed k=6.8 and $Q{\times}fo$=5,200GHz when it was sintered at $750^{\circ}C$. The maximum amount of $CaF_2$ in the CASB and 2MBS glass system without any detrimental effect on the sintering was 25.0 v/o and 15.0 v/o, respectively. The addition of $CaF_2$ in the glass systems improved the high frequency dielectric properties. In case of CASB+$CaF_2$ composite, k was 7.1 and $Q{\times}fo$ was 2,300GHz. And in case of 2MBS+$CaF_2$ composite, k was 5.9 and $Q{\times}fo$ was 8,100GHz. $CaF_2$ addition also reduced sintering temperature. Effects of $CaF_2$ on the dielectric and sintering properties was analyzed in terms of viscosity and crystallization behavior changes due to the interaction between $CaF_2$ and the glass systems.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1621-1622
• /
• 2006

This paper presents the effect of driving waveform for piezoelectric bend mode inkjet printhead with optimized mechanical design. Experimental and theoretical studies on the applied driving waveform versus jetting characteristic s were performed. The inkjet head has been designed to maximize the droplet velocity, minimize voltage response of the actuator and optimize the firing frequency to eject ink droplet. The head design was carried out by using mechanical simulation. The printhead has been fabricated with Si(100) and SOI wafers by MEMS process and silicon direct bonding method. To investigate how performance of the piezoelectric ceramic actuator influences on droplet diameter and droplet velocity, the method of stroboscopy was used. Also we observed the movement characteristics of PZT actuator with LDV(Laser Doppler Vibrometer) system, oscilloscope and dynamic signal analyzer. Missing nozzles caused by bubbles in chamber were monitored by their resonance frequency. Using the water based ink of viscosity of 4.8 cps and surface tension of 0.025N/m, it is possible to eject stable droplets up to 20kHz, 4.4m/s and above 8pL at the different applied driving waveforms.

• Journal of Energy Engineering
• /
• v.24 no.1
• /
• pp.132-136
• /
• 2015

The objective of this study is to investigate the effect of biodiesel blending on spray and combustion characteristics. In order to this, blended fuels containing 0, 5, 20, 50, 100% biodiesel in weight fraction was injected via common rail to constant volume combustion chamber. As a result, spray cone angle decreased and the Sauter mean diameter increased because of the higher dynamic viscosity and density of biodiesel, however, it does not seemed that spray penetration was affected by these factors considerably. In the combustion experiment, ignition delay of biodiesel was shorter than that of diesel due to higher cetane number. And the peak value of heat release rate increased and the end of combustion was advanced owing to higher combustion efficiency cause by the characteristic of oxygenated fuel.

• Journal of the Society of Disaster Information
• /
• v.9 no.1
• /
• pp.56-64
• /
• 2013

The study examines the quiet pavement using fine-size aggregates and warm-mix technique to reduce traffic noise. In order to evaluate the quality of pavement, mix design and laboratory tests were carried out. Test results showed that using 10mm aggregates can reduce the cantabro loss compared with 13mm aggregates due to increase contact area between aggregates. Mixing and compaction temperatures of warm mix quiet pavement should be determined by gyratory compactor test because it is used high viscosity asphalt binder. Using warm-mix additive could reduce compaction temperature by about $15^{\circ}C$. Noise measurement and permeability tests were conducted at the test road for evaluation of the field performance. All of quiet pavements meet the standard of permeability and have sufficient porosity. Noise reduction of the quiet pavement using fine-size aggregates is more effective than that using 13mm aggregates. In particular, the effect of noise reduction was noticeable at low speeds.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.3
• /
• pp.1252-1257
• /
• 2013

This study was used homomixer as one of the manufacturing method to establish optimal manufacturing condition with magnesium chloride emulsion as coagulant. The more rotational speed of homomixer was fast, the more particle size of magnesium chloride emulsion was minute. The particle size was distributed between 1 and $5{\mu}m$. The more minute particle size of emulsion had an effect on increasing viscosity of emulsion and delay of oil phase separation during storage period, so the quality of magnesium chloride emulsion had correlation with dispersed phase particle size. After all the experiments, when manufacturing magnesium chloride emulsion, it used more than 10,000 rpm of rotational speed of homomixer, it showed the best result as coagulant according to the state of texture and the water separation ratio of soybean curd.