• 한국식품과학회지
• /
• 제33권2호
• /
• pp.195-199
• /
• 2001

Amylograph를 이용하여 방사선 조사된 검은후추가루의 amylograph characteristics의 변화를 검사하고, 변화된 amylograph characteristics에 의해서 검은후추가루의 검지가 가능한지를 알아보기 위하여 본 실험은 수행되었다. Initial pasting temperatures, maximum viscosity temperatures는 조사선량의 증가에 따른 유의적인 변화가 관찰되지 않았다. Maximum viscosity(P), $93^{\circ}C$ viscosity, $93^{\circ}C$에서 15분 후의 viscosity(H), $45^{\circ}C$ viscosity(C), $45^{\circ}C$에서 30분 후의 viscosity, $45^{\circ}C$에서 60분 후의 viscosity는 조사선량이 증가할수록 감소하는 경향을 보여주었으며, p<0.05의 수준에서 통계적인 유의성이 관찰되었다. 그러나 breakdown(P-H), setback(C-P), 그리고 consistency(C-H)는 조사선량의 증가에 따른 명확한 차이가 관찰되지 않았다. breakdown(P-H)이 0.75, setback(C-P)이 0.88, consistency(C-H)가 0.31의 $R^2$ 값을 보인 것을 제외하고는 모든 amylograph characteristics 의 $R^2$ 값은 0.97 이상의 높은 상관성을 보여 주었다. 따라서 amylograph characteristics에 의해서 검은후추가루의 방사선 조사여부 확인이 가능하였다.

• Tribology and Lubricants
• /
• 제31권6호
• /
• pp.245-250
• /
• 2015

This study investigates the lubrication characteristics of fuel injection pumps with reference to different fuel oils. Medium-speed diesel engines use fuel oils with various viscosities, such as heavy fuel oil (HFO, which is a high-viscosity fuel oil) and light diesel oil (LDO, which is a low-viscosity fuel oil). When fuel oil with a low viscosity is used, both fuel oil and lubricating oil lubricate the system. Thus, the lubrication of the fuel injection pump is in a multi-viscosity condition when the fuel oil in use changes. We suggest three cases of multi-viscosity models, and divide the fuel injection pump into three lubrication sections: a, the new oil section; b, the mixed oil section; and c, the used oil section. This study compares the lubrication characteristics with variation of the multi-viscosity model, clearance. The volume of Section b does not affect the lubrication characteristics. The lubrication characteristics of the fuel injection pump are poor when high-viscosity fuel oil transfers to low-viscosity fuel oil. This occurs because the viscosity in the new oil section (i.e., Section a) dominates the lubrication characteristics of the fuel injection pump. However, the lubricant oil supply in the used oil section (i.e., Section c) can improve the lubrication characteristics in this condition. Moreover, the clearances of the stem and head significantly influence the lubrication characteristics when the fuel oil changes.

• 천문학회보
• /
• 제40권1호
• /
• pp.49.1-49.1
• /
• 2015

The origin of magnetic fields in the intracluster medium (ICM) is uncertain: it can be either primordial or astrophysical. Turbulence plays important roles in the origin of magnetic fields in the ICM. This is because turbulence can amplify a weak seed magnetic field very efficiently. The efficiency of the turbulence dynamo critically depends on the magnitude of viscosity: the smaller the viscosity is, the more efficient the turbulence dynamo is. In this talk, I'll discuss turbulence dynamo in both very small viscosity limit and very large viscosity limit. I'll show that when the viscosity in the ICM is comparable to the Spitzer viscosity, the origin of magnetic field in the ICM is likely to be astrophysical. On the other hans, when the viscosity is much smaller than the Spitzer value, the origin of magnetic field can be either astrophysical or primordial.

• Korea-Australia Rheology Journal
• /
• 제12권3_4호
• /
• pp.175-179
• /
• 2000

Rheological properties of chitosan solutions were investigated as a function of polymer concentration. The viscosity curves for chitosan solutions consisted of two distinct viscosity regions, the Newtonian zero-shear viscosity (η$_{0}$) region and the shear rate dependent apparent viscosity (η$_{app}$) region. The shear rate dependence of viscosity was more clearly observed at higher chitosan concentrations. The critical coil overlap parameter (C＊〔η〕) was determined to be approximately 3.2 from a plot of zero-shear specific viscosity η$_{sp,0}$ vs coil overlap parameter (C〔η〕), which was lower than C〔η〕4.0 reported for other random coil polysaccharides. It was also found that the slope of η$_{sp,0}$ vs C〔η〕 was 3.9 at concentrated C〔η〕>C＊〔η〕domain, while 1.2 at dilute C〔η〕$_{0}$ ${\gamma}$/${\gamma}$$_{0.8}$ relation.ion.n.n.

• 한국구조물진단유지관리공학회 논문집
• /
• 제4권3호
• /
• pp.177-184
• /
• 2000

The purpose of this study is to evaluate the performance of a new viscosity modifying admixture for concrete agent. For this purpose, selected test variables were the ratio of water to cement, the ratio of cement to fine aggregate, contents of superplasticizer, contents of viscosity modifying admixture. As a result of this study, it has been found that addition of viscosity modifying admixture to mortar modfies its fluidity and reduces its segregation by increasing the mortar viscosity. And it has been found that a new viscosity modifying admixture do not significantly affect the setting time, air content of mortar.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2017년도 추계 학술논문 발표대회
• /
• pp.32-33
• /
• 2017

In order to improve the flow performance of high performance concrete, use of high performance water reducing agent and low viscosity type water reducing agent is a study of suitable range of use due to side effects. in this study, we aimed at reducing viscosity and yield value using high performance water reducing agent and low viscosity type water reducing agent, and this was evaluated using a rheometer. as a result of analysis of viscosity and yield value, it was found that the high performance water reducing agent has higher reduction effect than the low viscosity type water reducing agent. however, the larger the viscosity lowering effect is, the lower the usable range is, compared to general high performance water reducing agents, and it was found that sufficient consideration for this judgment of appropriate quantity is necessary.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2018년도 추계 학술논문 발표대회
• /
• pp.46-47
• /
• 2018

High performance concrete with low water-to-cement ratio has been widely used with increased demand of high rising buildings and huge scaled structures. Additionally, for high performance concrete, various SCMs are replaced to improve its performance from fresh state to hardened state. With the drawback of increased viscosity of the concrete mixture for high performance concrete, low-viscosity typed high range water reducer is the relatively new admixture. Therefore, as a goal of the research, under using various SCMs with wide range of content, the performance of low-viscosity typed high range water reducer was evaluated. Especially, in this research, the influence of low-viscosity typed high range water reducer on rheological properties including plastic viscosity and yield stress were assessed. As a result of the research, it is expected to provide a fundamental information of low -viscosity typed high ranged water reducer on high performance concrete with various conditions of SCMs.

• Journal of Microbiology and Biotechnology
• /
• 제8권2호
• /
• pp.178-181
• /
• 1998

An exopolysaccharide, designated as A49-Pol, was produced from Bacillus polymyxa KCTC 8648P in nitrogen sufficient conditions. The viscosity of the culture broth increased up to $2\times10^4$cP in 38 hours of culture and then decreased to $1.5\times10^4$CP at 48 hours. The $1.0\%$ (w/v) solution of purified A49-Pol represented pseudoplasticity with a viscosity of $2.7\times10^4$cP which was two times higher than xanthan at the same concentration. The viscosity of the A49-Pol solution was also greatly affected by its concentration in comparison with the xanthan solution. The viscosity of $1.0\%$ A49-Pol solution was 930-fold higher than its $0.2\%$ solution, whereas the corresponding viscosities of xanthan solution experienced only l7-fold difference. The viscosity was observed to be maximum at pH 7.0 in both A49-Pol and xanthan solutions, and gradually decreased as the pHs of the polysaccharide solutions went to acidic or alkaline regions. The viscosity of A49-Pol solution was very sensitive to temperature compared to xanthan and decreased with increasing temperature. The viscosity of $0.6\%$ solution of A49-Pol was 8,100 cP at $10^{\circ}C$ and 55 cP at $50^{\circ}C$. The viscosity was also affected by the presence of surfactants such as Span 20 and Triton X-l00 ; with $0.5\%$ Triton X-l00 (v/v), the viscosity of A49-Pol solution increased by $50\%$.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2014년도 제49회 KOSCO SYMPOSIUM 초록집
• /
• pp.21-24
• /
• 2014

In the entrained-flow coal gasifier, coal ash turns into a molten slag most of which deposits onto the wall to form liquid and solid layers. Critical viscosity refers to the viscosity at the interface of the two layers. The slag layers play an important role in protecting the wall from physical/chemical attack from the hot syngas and in continuously discharging the ash to the slag tap at the bottom of the gasifier. For coal with high ash melting point and slag viscosity, CaO-based flux is added to coal to lower the viscosity. This study evaulates the effect of critical viscosity temperature and ash/flux ratio on the slag behavior using numerical modelling in a commercial gasifier. The changes in the slag layer thickness, heat transfer rate, surface temperature and velocity profiles were analyzed to understand the underlying mechanism of slag flow and heat transfer.

• Advances in materials Research
• /
• 제3권2호
• /
• pp.91-103
• /
• 2014

A study that demonstrates how to investigate the molded part quality and the consistency of injection process based on the rheological concept is proposed. It is important for plastic material whose melt viscosity is variable with respect to the processing condition. The formulations to couple the melt viscosity with injection pressure and fill time are derived first. Taking calculations of the measured pressure and the time by using these formulations, the melt viscosity in injection process can be determined on machine. As the relation between the injection speed and the melt viscosity is constructed, the influences of the setting parameter of injection machine on the molded part quality can be investigated through evaluating the state of the melt viscosity. In addition, a pressure sensor bushing (PSB) designed with a quick installation feature is also provided and validated. The results show that a higher injection speed improves the tensile strength of the molded part but also the consistency of the molded part quality. This work provides an alternative to evaluate the molding quality scientifically.