• Transactions of Materials Processing
• /
• v.12 no.1
• /
• pp.34-42
• /
• 2003

This paper presents a rigid-plastic finite element method to handle the frictional contact problem between two deformable bodies experiencing large deformation. The variational formulation combined with incremental quasi-static model is employed for treating the contact boundary condition. The frictional behavior of the model obeys Coulomb's law of friction. The proposed contact algorithms are classified into two categories, one for searching contacting nodes and the other for calculating contact forces at the contact surface. A slave node and master contact segment are defined using the geometric condition of finite elements on the contact interface. The penalty parameter is used to limit the penetration between contacting bodies, and the finite elements are coupled with contact boundary elements.us gates and cavity thicknesses. Through this study we have observed that the jetting is related to the die swell of material. This means that the jotting is strongly affected by the elastic flow property rather than the viscous flow property in viscoelastic characteristics of molten polymer. Different resins have different elastic properties, and elastic flow behavior depends on the shear rate of flow, i.e. injection speed. Large die swell would eliminate jetting however, the retardation of die swell would stimulate jetting. In the point of mole design, reducing the thickness ratio of cavity to gate can reduce or eliminate jetting regardless of amount of elasticity of polymer melt.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2004.11a
• /
• pp.186-194
• /
• 2004

Experiments were conducted to determine the structural static and dynamic characteristics of air foil bearings. The housing of the bearing on the journal was driven by an impact hammer which was used to simulate dynamic forces acting on the bump loll with various leading condition. Two different bump foils (Cu-coated bump and viscoelastic bump) were tested and the static and dynamic coefficients of two bump foils compared, based on the experimental measurements for a wide range of operating conditions. The static and dynamic characteristics of air foil bearings were extracted 0rpm the frequency response function by least square method and IV(Instrumental Variable) method. The experiment was tested at 0rpm and $10,000\~16,000rpm$, and loaded on $50\~150N$. From the test results, the possibility of the application of high load and high speed condition is suggested.

• Proceedings of the KOSOMBE Conference
• /
• v.1991 no.05
• /
• pp.74-78
• /
• 1991

Conventional compression bone fracture plates sometimes cause osteoporosis under the plate due to their high rigidity which in turn transfer physiological load mostly through the plates and screws. In order to prevent the osteopenia we have designed a system which have a viscoelastic washer between plate and screw head. The washer is made of a biocompatible ploymer (untra high molecular weight polyethylene, UHMWPE). Three-dimensional finite element meshes of the human femur with the conventional and new concept bone plate ere generated and the comparative stress analyses are performed with static half-stance loading condition. The results of analyses showed that could reduce the stress shielding effect compared with the conventional plate.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2000.04b
• /
• pp.141-149
• /
• 2000

This study performs the elastic and viscoelastic analysis of composite continuous beams with flexible shear connectors. Due to creep and shrinkage of the concrete part, the stress redistribution between the concrete slab and steel beam, and the evolution of the redundant restraint reaction occur with time. Using the equation of equilibrium, internal and external compatibility condition, and constitutive relationships, mathematical formulations are formulated. The solution is obtained by means of numerical step-by-step techniques and the finite difference method. Numerical parametric studies are performed to evaluate the stress redistribution, and the evolution of the redundant restraint reaction. The parameters include the stiffness and spacing of shear connectors, the age of concrete at loading, and the relative humidity.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.656-661
• /
• 2005

An optimization formulation of unconstrained damping treatment on beams is proposed to minimize vibration responses using a numerical search method. The fractional derivative model is combined with RUK's equivalent stiffness approach in order to represent nonlinearity of complex modulus of damping materials with frequency and temperature. The loss factors of partially covered unconstrained beam are calculated by the modal strain energy method. Vibration responses are calculated by using the modal superposition method, and of which design sensitivity formula with respect to damping layout is derived analytically. Plugging the sensitivity formula into optimization software, we can determine optimally damping treatment region that gives minimum forced response under a given boundary condition. A numerical example shows that the proposed method is very effective in minimizing vibration responses with unconstrained damping layer treatment.

• Elastomers and Composites
• /
• v.32 no.1
• /
• pp.29-36
• /
• 1997

The change of elastic modulus(E'), loss modulus(E"), and loss $tangent(tan{\delta})$ were investigated on condition of double strain amplitude (DSA) at temperature of $-40{\sim}80^{\circ}C$ for carbon black filled natural rubber. E', E", and $tan{\delta}$ were increased as it closed to the glass transition temperature due to decrease of rubber network flexibility and carbon black agglomerate interaction. In the micro strain range, energy loss showed maximum value because of the chain slippage in rubber matrix, but the regeneration of carbon black agglomerate and rubber matrix affected decrease of energy loss over the mid-range strain. As a results of regression analysis, $E'\;_{max}$ correlation with ${\Delta}E'$ $(E'\;_{0.4%DSA}-E'\;_{2.0%DSA})$ showed linear relationship.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.8-13
• /
• 1996

A relatively new non-traditional finishing process called Abrasive Flow Machining(AFM) is being used to deburr, polish and radius workpiece or produce compressive residual stresses by flowing an abrasive-laden viscoelastic compound across the surface to be machined. This paper presents the effects of AFM on surfaces of tool steel produced by EDM and W-EDM. Using AFM, white layer produced by EDM is erased almost equally and the amount of metal removal is significantly affected the initally machined surface condition of workpiece. The dimension of workiece is enlarged and its surface roughness is improved as AFM time is increased. The optimal AFM time can be established from the experimental results. It is considered that the grinding method lide AFM is useful to grind complex or slim geometry of workpiece even. Scanning Electron Microscopy(SEM) was used to study the surface characteristics of the workpiece before and after AFM.

• Laser Solutions
• /
• v.11 no.3
• /
• pp.10-15
• /
• 2008

This study is aimed to analyse the laser glass bonding process numerically. Due to the viscoelastic behaviour of glass, the extremely large deformation of the frit seal is resulted continuously over the transition temperature, so that the thermal boundary condition be changed in the entire calculation process. The commercial FEM algorithm is restrictively able to remesh the large geometrical boundary shape and to adapt the boundary conditions simultaneously. According to our manual adaptation of increasing the laser line intensity to 700 mW/mm, it is possible to estimate the thermal glass bonding process under the fracture stress in principle. But it should be studied further in the case of high laser line intensity.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.02a
• /
• pp.61-67
• /
• 2002

The present work is investigated optimal design for the injection molding process of a hand brake cover. The viscoelastic flow through a hand brake cover shape in the mold were calculated and compared with the experimental data. Numerical analysis reasonably predicted the general performance i.e hold pressure, cooling time and hold pressure time. In order to determine optimal process parameters, Numerical analysis and experiments have been performed for various process conditions. In this study, we obtained to increase in the productivity by $160\%$ by optimal process conditions.

• Elastomers and Composites
• /
• v.48 no.2
• /
• pp.103-113
• /
• 2013

The properties of the rubber composites containing a silane and silica were evaluated by changing the mixing time and temperature, in order to find the optimum mixing conditions. Characteristics of the compounds were evaluated after mixing at $120^{\circ}C$, $140^{\circ}C$, and $160^{\circ}C$ with various mixing time. With increasing of mixing time, mooney viscosity decreased while the bound rubber contents of the compounds increased. Viscosity rise by increased mixing time was bigger at low temperature and the higher the mixing temperature the faster in the formation of bound rubber. With lower mixing temperature of $120^{\circ}C$, cross-linking rate was almost constant. Dynamic viscoelastic properties and dispersity of the compound showed that dispersion of ingredients and reaction was not sufficient with the mixing time of less than 10min. On the contrary, with high temperature, it was obvious that good dynamic and physical properties could be obtained due to sufficient coupling reaction, however it was thought this high temperature is not optimum because of sensitive cross-linking rate and physical properties and excessive formation of bound rubber. Consequently, it was confirmed that the mixing condition of 10min at $140^{\circ}C$ was optimum for the silane coupling reaction and dispersion of functionalized S-SBR containing silica and silane.