• 한국소음진동공학회논문집
• /
• 제21권2호
• /
• pp.129-136
• /
• 2011

The aim of this paper is to present the method of identifying the impact location on the plate. This basic research has the future purpose to achieve the human-interaction technology based on the signal processing, piezoelectric materials, and wave propagation. The present work concerning the location identification of a single impact on the plate simulated the waveform numerically generated by impact force and applied the SWFOM(sliced Wigner higher fourth order moment) to the waveform to get the arrival time differences due to impact force between three sensors attached to the plate. The simulated signal is useful to get the information for time interval for the only direct wave. This information is used the source localization by using experimental work. The measured signal is also used for source localization of a single impact based on the higher order time frequency as a novel work.

• 한국소음진동공학회논문집
• /
• 제16권6호
• /
• pp.565-573
• /
• 2006

Acoustic analysis of a moving sound source required that the measured sound signals be do-Dopplerized and restored as of the original emission signals. The purpose of this research is development of beamforming technique can be applied to the rotor noise source identification. For the do-Dopplerization and reconstruction of emitted sound wave, Forward Propagation Method is applied to the time domain beamforming technique. And validation test were performed using rotating sound source constructed by bended pipe and horn driver. In the validation test using sinusoidal sound wave, sufficient performance of signal processing can be seen, and the effect of measuring duration for accuracy was compared. In the prop-rotor measurements, the acoustic source locations were successfully verified in varying positions for different frequencies and collective pitch angle, in hover condition.

• 한국소음진동공학회논문집
• /
• 제19권7호
• /
• pp.710-718
• /
• 2009

The time difference of arrival(TDOA) algorithm is being used widely for identifying the location of a source emanating either electrical or acoustic signal. It's application areas will not be limited to identifying the source at a fixed location, for example the origin of an earthquake, but will also include the trajectory monitoring for a moving source equipped with a GPS sensor. Most of the TDOA algorithm uses time correlation technique to find the time delay between received signals, and therefore difficult to be used for identifying the location of multiple sources. In this paper a TDOA algorithm based on cross-spectrum is developed to find the trajectory of two sound sources with different frequencies. Although its application is limited to for the sources on a disk plane, it can be applied for identifying the locations of more than two sources simultaneously.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.152-155
• /
• 2002

An industrial robot noise has various noise sources such as gears, motors, bearings, and controller fans. Among these, gears are the most dominant source for noise. The gear noise, caused by tooth profile, elastic deformation, machining error and wear, is directly correlated with the transmission error of mating gear. Due to the fact that has several axis and many gears, it is difficult to understand the characteristics of the vibration and noise of robots. In this study, some advanced analysis techniques based on digital signal processing such as power spectrum, time spectral map, RPM map, and etc., were applied for locating the dominant frequency components of the robot noises and identifying their sources. In addition, sound quality analysis was performed in order to evaluate the operator's annoyance. The noise and vibration measurements were carried out at several points during the operation of each axis considering the effect of load and posture of the robot. Eased on the results, proper countermeasures to reduce excessive noise level have been suggested considering the characteristics of sources.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.911-915
• /
• 2004

Recently, several experimental techniques for identifying the noise sources distributed over a moving vehicle are being developed and used in order to design a low noise vehicle. The beamforming method, which uses phase information between several microphones to localize the source position, is proved to be one of the promising techniques applicable even under complicated test environments. In this study a beamforming algorithm is developed and applied to measure the dominant noise sources on a passenger car moving at constant speed. Unlike the acoustic signals from a stationary noise source, the sound generated from a moving source is distorted due to the Doppler effects. The sound pressure are measured with an spiral array system composed of 26 microphones and a pair of photo sensors are used to measure the. vehicle speed. The information about the speed and relative position of the vehicle are used to eliminate the Doppler effects from the measured pressure signal by using a de-Dopplerization algorithm. The noise generated from a moving vehicle can be grouped in many ways, however, tire noise and the noise generated from the engine are distinguishable at the speeds being tested.

• 한국정밀공학회지
• /
• 제22권10호
• /
• pp.80-89
• /
• 2005

In this paper, time-frequency analysis using wavelet packet transform and advanced-MDSA (Multiple Dimensional Spectral Analysis) which based on wavelet packet transform is applied fur fault source identification and diagnosis of early detection of fault non-stationary sound/vibration signals. This method is analyzing the signal in the plane of instantaneous time and instantaneous frequency. The results of ordinary coherence function, which obtained by wavelet packet analysis, showed the possibility of early fault detection by analysis at the instantaneous time. So, by checking the coherence function trend, it is possible to detect which signal contains the major fault signal and to know how much the system is damaged. Finally, It is impossible to monitor the system is damaged or undamaged by using conventional method, because crest factor is almost constant under the range of magnitude of fault signal as its approach to normal signal. However instantaneous coherence function showed that a little change of fault signal is possible to monitor the system condition. And it is possible to predict the maintenance time by condition based maintenance for any stationary or non-stationary signals.

• 한국소음진동공학회논문집
• /
• 제20권11호
• /
• pp.1018-1024
• /
• 2010

The printer noise consists of the noise of the various components and parts such as motor, fan and solenoid. And the human's printing sound recognition shows various aspects when the printer starts to print papers because the components operate at the same time. Especially, printers are usually installed in the quiet office room. Therefore the printing noise is related to its competitiveness in the market. The importance of the printer sound qualities is increasing and it is necessary to develop the sound quality evaluation system, so it is a key point to identify the noise source of the printer and develop the sound quality index to each component. By using this evaluation system, it is possible to evaluate the sound quality of a prototype printer compared to the already existing one. In this paper, the printer sound quality evaluation system was developed by the following steps. Firstly, the signal processing method was applied to the recorded printing sound to identity and split the noise of components. Secondly, the MLR(multiple linear regression) method and the psychoacoustics were used to develop the sound quality index. Finally, the improvement of the printer sound quality is possible by using the result of the MLR and the path analysis. The output of this research will be applied to the development of a new printer.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1990년도 추계학술대회논문집; 한양대학교, 서울; 24 Nov. 1990
• /
• pp.9-14
• /
• 1990

맥동 연소기는 기존의 연속 연소식 연소기에 비하여 높은 열효율, 소형화, 연소과정의 개선, 시동후 점화플러그 및 송풍팬의 불필요, 자력 배기와 장시 간 안전 운전등의 장점들로 인하여 최근 연구대상으로서 주목을 받고 있다. 맥동연소 현상은 1800년경부터 알려졌음에도 불구하고 기본적인 연소메카니 즘 및 기본동작 원리에 대한 미비점 및 높은 소음 등으로 인하여 종래의 연 구는 거의 실험을 통하여 이루어 졌으며 이러한 것들이 현재까지도 맥동 연 소기의 발전에 걸림돌이 되고 있다. 맥동 연소기가 산업용 및 가정용 열기기 로서 사용되기 위하여 진동과 소음의 감소에 대한 엄격한 요구를 만족하지 않으면 안된다. 따라서, 그에 대한 효과적인 방지 설계를 하기 위하여 진동 원과 소음원이 어느 부위에서 전달되어 오는지를 파악하는 것이 중요하다.. 본 연구에서는 맥동연소기의 소음원을 규명하기 위하여 종래에 사용되어 온 주파수 응답함수법과 소음원간에 강한 상관관계가 존재하는 경우에 사용되 는 기여도함수법을 이용하여 다차원 스펙트럼해석법에 의하여 입출력간의 기여관계를 규명하였다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권12호
• /
• pp.691-697
• /
• 2000

A fiberoptic sensor using a low-coherence SLD as a light source has been studied. The sensor system employing an intrinsic fiber Fabry-Peort interferometer as a sensing tip and a fiber Mach-Zehnder interferometer as a processing one, overcomes the ambiguous reading caused by the highly periodic natrue of conventional high-precision interferometric sensors and provides unambiguous identification of the desired phase among several candidates on the transfer function of an interferometric signal. A tentative application to the temperature sensor shows the potential that the fiberoptic sensor has a side-dynamic range of $0-900^{\circ}C$ as well as reasonable resolution higher than $0.1^{\circ}C$ without ambiguity. Due to the inherent property of the optical fiber itself and the intrinsic fiber Fabry-Perot interferometer, the proposed fiberoptic sensor will give obvious benefits when it is applied to harsh environments to monitor some physical parameters such as temperature, strain, pressure and vibration.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 춘계학술대회 논문집
• /
• pp.348-353
• /
• 2012

This paper presents the HRTF based experimental approach to figure out why the human auditory perception on the interior noise source including the directional tonal components does not well match with the dominant features extracted from recorded acoustic signals in terms of psycho-acoustics. Since the general objective evaluation models for tonalness among various sound attributes are a function of width, frequency, excessive level of tonal components respectively, the directional tonal components cannot be properly evaluated without considering the effects of head-related transfer function on the binaural auditory perception. Thus, the directivity of source is additionally considered to prevent the erroneous conclusions from the same sound source in the process of source identification. The signal synthesis technique is used to solve a little difficulty in measuring all of desired acoustic signals for jury evaluation. The sound attributes of synthetic acoustics signals are analyzed to roughly predict the results of jury evaluation in advance by using sound quality factors such as loudness, sharpness, roughness, fluctuation strength and tonality. The jury evaluation is carefully conducted based on the recommended guideline suggested by N. Ottoet al. Each sound is respectively evaluated by selecting a value between -2 and 2 in intervals of 0.2 point. Through above procedure, based on the results of jury evaluation, it is confirmed that serious problems can be caused in the process of analyzing the dominant sound attributes in terms of psycho-acoustics according to the type of a microphone and a playback system.