• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.79-82
• /
• 2004

In general, compressors for refrigerators are major noise source in home environment. The vibration originated from a pump of a compressor can make noise through suspension springs and a LDT(Line Discharge Tube). Especially for the inverter motor driven compressor, the vibration is more serious than it of the constant speed compressors. Because the operation frequency range of an inverter motor driven compressor is very wide from 1600 rpm to 4200 rpm. In this paper, we propose the numerical model to reduce vibration by designing weight balancers and grommets. Results for analytical investigations on the exciting force and moment at the pump mass center, weight balancers and exciting frequency variation are presented.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.3
• /
• pp.359-364
• /
• 2013

In order to use a linear vibration motor for the actuator of a haptic interface, the motor must provide a higher reaction rate and longer service life than typical rotational motors with an eccentric mass. In this paper, we propose a linear vibration motor that is equipped with a voice-coil actuator and permanent-magnet springs. To concentrate the magnetic flux in the actuator, a Halbach-style magnetization pattern is used. Permanent-magnet springs replace mechanical springs to help increase the service life. We use the method of equivalent current sheets and the method of images to analyze and model the proposed vibration motor. These methods are validated using finite element analyses and experiments. A prototype motor is designed and fabricated. Tests with the prototype show the feasibility of the proposed linear vibration motor.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.264-269
• /
• 2008

This paper presents the summary of control of abnormal vibration found in the COP motors of a nuclear power plant. All six identical units of COP pump-motor assemblies showed unstable vibration pattern of which one or two showed higher vibration enough to exceed the allowable level from the installation stage. Many trials of test, measurement, overhaul and replacement had been repeated to investigate and solve the problem but only to reach unsatisfactory settlement. Recently several times of site tests are made and followed by significant diagnostic actions in which the authors group participated. It was found that the coupled shafting system of motor and pump is in close resonance with the $1^{st}$ shaft rotating speed. Redesign of topside motor bearing clearance is made to increase bearing stiffness and hence to avoid the resonance which consequently led to reduce the troubled vibration to allowable and stable status.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1996.04a
• /
• pp.163-168
• /
• 1996

In this paper a new dynamic damper driven by DC linear electric motor, is proposed for suppressing wide-band vibration. First, the reason for the incapability of a conventional dynamic damper to suppress wide-band vibration is explained. Then, with its defects taken into consideration, the principle of wide-band vibration control is presented. Finally, experiments ar conducted verifying the control effect of the active dynamic damper for suppressing wide-band vibration.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.316.1-316
• /
• 2002

The regression analysis in the six sigma process is used to reduce the vibration of a small universal motor, The vibration characteristics and contribution of each part to overall vibration of an electric grinder is investigated through various vibration measurements and frequency analysis for the assembled and disassembled one. (omitted)

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.11 no.9
• /
• pp.454-461
• /
• 2001

Acoustic noise and vibration of a BLDC motor is a coupled phenomenon between mechanical characteristics and electromagnetic origins through the motor air-gap. When a relative misalignment of rotor in the air-gap center exists on the assemblage, it is considered to influence the motor system characteristics. In this paper, the back electro motive force(BEMF) is analyzed by Finite Element Method(FEM) and verified by experiments for the SPM and IPM type motors. For magnetic field analysis, a FEM is used to account for the magnetic saturation. Using these results, the FEM is made to determine the appropriate electromagnetic field analysis in BLDC motors with rotor eccentricity ratio. A radial magnetic imbalance force of BLDC motor with rotor eccentricity is analyzed. Results demonstrate that the imbalance force is increased according to the degree of misalignment. An IPM motor, mostly chosen to realize high-speed operation, shows a worse effect on magnetic unbalanced forces and dynamic responses compared with SPM motor due to magnetic saturation when the rotor eccentricity exists.

• Journal of information and communication convergence engineering
• /
• v.6 no.4
• /
• pp.421-424
• /
• 2008

In torque transmission system, we must suppressed vibration for Accuracy characteristic response of motor, Therefore, vibration suppression factor is very important motor control. To suppress vibration, a various control method has been proposed. Specially, one method of vibration suppression used disturbance observer filter. This method is torsion torque passing disturbance observer filter. By the estimated torsion torque feedback, vibration can be suppressed. The CDM(coefficient diagram method) is used to design the filter and Proportional controller. But using coefficient diagram method, not adapted controller parameter in disturbance. For this solution, we used fuzzy controller for auto tuning controller parameter. We proved this approach is confirmed by simulation.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.895_896
• /
• 2009

this paper presents a rotor shape optimization of interior type permanent magnet (IPM) motor for vibration minimization. the vibration of permanent magnet motor is generated by cogging torque, radial force and commutation torque ripple which are electromagnetic source of vibration. In order to minimize the vibration, the optimal notches are put on the rotor pole face and the arc type pole face is applied. The variations of cogging torque and radial force of each model vibration frequency are computation by finite element method (FEM) and the validity of the analysis and rotor shape design is confirmed by vibration experiments.

• Journal of Electrical Engineering and Technology
• /
• v.1 no.1
• /
• pp.85-91
• /
• 2006

Recently, the reduction of electromagnetic vibration and noise of a capacitor motor (CRM) has become a very important subject from the standpoint of environmental improvement. Therefore, the authors have studied the characteristics of the dominant electromagnetic vibration of the CRM under load condition. In this paper, the effects of slot combination and skewed slot on the dominant electromagnetic vibration of a CRM under load condition are discussed both theoretically and experimentally. As a result, the characteristics of the dominant electromagnetic vibration for the slot combination and the reduction effect of the skewed slot on the electromagnetic vibration are clarified for a 4-pole CRM.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.41.2-41
• /
• 2001

A torque transmission system, which is composed of several gears and couplings, is flexible. Therefore, the torsion vibration occurs when the motor speed abruptly changes. Consequently, for Accuracy characteristic response of motor, we must suppressed vibration. Therefore, vibration suppression is very important motor control. To vibration suppression, various control method have been proposed. Specially, one method of vibration suppression used disturbance observer filter. This method is torsion torque passing disturbance observer filter. By feedback of the estimated torsion torque, the vibration can be suppressed The coefficient diagram method is used to design the filter and proportional controller.