• 한국항공우주학회지
• /
• 제37권6호
• /
• pp.586-594
• /
• 2009

본 논문은 국내 최초의 소형 복합재 위성인 과학기술위성3호의 proto 모델에 대하여 랜덤, 정현파, 충격 진동응답에 대한 연구이다. 과학기술위성3호의 구조체는 여러 장의 패널을 서로 연결하여 만든 박스형의 구조이며 패널은 탄소섬유강화 복합재를 적층한 스킨에 알루미늄 허니컴 구조를 접착한 하이브리드샌드위치구조로 되어있다. 상용 FEA 코드인 MSC/NASTRAN을 사용하여 주파수 및 시간영역에서 위성의 설계요구조건으로 주어진 진동시험수준에 대한 모드, 응력, 변위, 가속도의 응답을 계산하였다. 이러한 해석결과를 바탕으로 발사 시 야기되는 진동으로 인한 파괴, 안전율 및 설계 타당성을 검토하였다. 이 연구결과들은 실제 위성구조설계 신뢰성 실험에 있어서 검증 및 비교의 자료로 사용될 수 있고, 위성개발의 중요한 자료로 활용된다.

• Nuclear Engineering and Technology
• /
• 제41권6호
• /
• pp.821-830
• /
• 2009

In this paper, modal testing and finite element modeling results to identify the modal parameters of a nuclear fuel rod as well as its cladding tube are discussed. A vertically standing full-size cladding tube and a fuel rod with lead pellets were used in the modal testing. As excessive flow-induced vibration causes a failure in fuel rods, such as fretting wear, the vibration level of fuel rods should be low enough to prevent failure of these components. Because vibration amplitude can be estimated based on the modal parameters, the dynamic characteristics must be determined during the design process. Therefore, finite element models are developed based on the test results. The effect of a lumped mass attached to a cladding tube model was identified during the finite element model optimization process. Unlike a cladding tube model, the density of a fuel rod with pellets cannot be determined in a straightforward manner because pellets do not move in the same phase with the cladding tube motion. The density of a fuel rod with lead pellets was determined by comparing natural frequency ratio between the cladding tube and the rod. Thus, an improved fuel rod finite element model was developed based on the updated cladding tube model and an estimated fuel rod density considering the lead pellets. It is shown that the entire pellet mass does not contribute to the fuel rod dynamics; rather, they are only partially responsible for the fuel rod dynamic behavior.

• 한국산학기술학회논문지
• /
• 제16권12호
• /
• pp.8654-8664
• /
• 2015

기계, 건축, 토목공학 분야 등에는 불균일 단면을 갖는 보 형태의 구조물들이 널리 사용되고 있다. 본 논문은 양단이 단순 지지된 보 구조물들의 동특성과 진동에 대한 문제를 다루며, 국부좌표를 사용한 지배방정식이 유도된다. 갤러킨의 모드합 방법으로 해가 가정되고, 고유진동수를 구하는 행렬식을 푸는 데는 이분법을 적용하였다. 유한요소법이 단지 기하학적 경계조건만을 만족시키는 허용함수를 사용하는 반면, 본 논문에서는 갤러킨의 모드합 방법을 적용하여, 지배방정식과 경계조건을 모두 만족하는 고유함수를 사용하였다. 계의 동특성을 알기위해, 네 종류의 불균일 단면을 갖는 단순 지지 보에 대해 모달 해석과 시험이 수행되었으며, 해석 결과는 실험 결과와 근사한 일치를 나타내었다.

• 한국생산제조학회지
• /
• 제22권4호
• /
• pp.717-722
• /
• 2013

In this study, we investigated the design of a wire wedge bonding ultrasonic tool horn using finite element method (FEM) simulations. The proposed method is based on an initial design estimate obtained by FEM analysis. An ultrasonic excitation causes various vibrations of a transducer horn and capillary. A simulated ultrasonic transducer horn and resonator are then built and characterized experimentally using a laser interferometer and electrical impedance analyzer. The vibration characteristics and resonance frequencies close to the exciting frequency are identified using ANSYS. FEM analysis is developed to predict the resonance frequency of the ultrasonic horn and use it in the optimal design of an ultrasonic horn mode shape.

• 한국자동차공학회논문집
• /
• 제3권1호
• /
• pp.20-32
• /
• 1995

Springs for vehicle suspension control the vibration of a car and influence on the ridability, safety, and life of a car. In the paper, the computer aided design program has been developed, which design the leaf spring shape from the given specifications using basic theory and the expert's knowledge, and the design results are checked by the analysis theory in order to increase the accuracy, and feed back to the design input. For the purpose of easy use, this program consists of pull-down menu and interactive input mode. To prove the effectiveness of this program. two springs, of which one is symmetric, other asymmetric, are designed and analyzed, and the outputs are compared to the experiments. Considering the tolerance of the given specifications, the results are good.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.321-321
• /
• 2010

In this paper, we propose a novel type shaft-less ring type ultrasonic motor. A traveling wave rotary type ultrasonic motor is selected as a base model. The newly designed stator has two piezoelectric ceramic rings which are bonded in sandwich shape as traveling wave generator. So, we can expect to produce higher torque. The proposed model has the rotor structure that coupled with the stator provokes the pressure, this model do not install the separate plate any spring device. We used the finite element method to verify the operation principle and to compute the vibration mode of proposed model.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2000년도 춘계학술대회 논문집
• /
• pp.89-94
• /
• 2000

Because the structural elements used in the automobile, astronautic and ship industries are put in dynamic loading environments, much interest is given to the damping of the structural elements, as well as high flexural rigidity and strength per density. Therefore, in this study, the structural damping value of the aluminum honeycomb sandwich plate(AHCP) has been experimentally extracted, and directly applied to the finite element, for the dynamic analysis of the plate considering the structural damping. The analysis results of this theory was compared with the results of the actual modal analysis method. It was observable that the two analyses concurred, establishing the structural damping and analysis method of the AHSP.

• 한국공작기계학회논문집
• /
• 제10권1호
• /
• pp.16-22
• /
• 2001

In this study for reduction degree of freedom of dynamic model, a mixed method to combined finite element method and transfer matrix method is presented. This offers the advantages of an automatic reduction in the size of the eigenvalues problem and of a straightforward means of dynamic substructuring. The analytical procedure in this method for dynamic analysis of 3-dimensional cantilevered box beam are described. the result of numerical example is shown to demonstate the efficiency and accuracy of this method. The result form this example agree well those obtained by ANSYS, By using this technique, the number of nodes required in the regular finite element method is reduced and therefore a smaller com-puter can be used.

• 한국생산제조학회지
• /
• 제20권5호
• /
• pp.570-575
• /
• 2011

Ultrasonic metal welder is consisted of power supply, transducer, booster, and horn. Precise designing is required since each parts' shape, length and mass can affect driving frequency and vibration mode. This paper analyzed Cu sheet deposition characteristics using ultrasonic metal welder and tension tester. A horn suitable for 40,000Hz was attached to the ultrasonic metal welder in order to weld Cu plates. The Cu sheet welding was done with different amplitude, pressure, and welding time, and its maximum tension was measured with tension tester. Maximum tension of 153.87N was obtained when the pressure was 2.0bar, amplitude was 80%, and welding time was 0.30s. Therefore, excessive welding condition negatively influences maximum tension measurement result.

• Structural Engineering and Mechanics
• /
• 제31권3호
• /
• pp.277-296
• /
• 2009

The paper investigates the dynamic behaviour of stiffened panels. The coupled differential equations for eccentric stiffening configuration are first derived. Then a semi-analytical procedure for dynamic analysis of stiffened panels is presented. Unlike finite element or finite strip methods, where the plate is discretized into a set of elements or strips, the plate in this procedure is treated as a single element. The potential energy of the structure is first expressed in terms generalized functions that describe the longitudinal and transverse displacement profiles. The resulting non-linear strain energy functions are then transformed into unconstrained optimization problem in which mathematical programming techniques are employed to determine the magnitude of the lowest natural frequency and the associated mode shape for pre-selected plate/stiffener geometric parameters. The described procedure is verified with other numerical methods for several stiffened panels. Results are then presented showing the variation of the natural frequency with plate/stiffener geometric parameters for various stiffening configurations.