• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1994.10a
• /
• pp.210-216
• /
• 1994

본 연구에서는 볼 베어링의 전동체 회전에 의해 발생하는 원심력, 자이로스코픽 모멘트, 하중 방향선에 대한 전동체의 하중 분포 변화 등을 고려하여, 볼 베어링의 강성 특성을 해석하고, 볼 베어링으로 지지되는 간단한 회전축 계에 해석 결과를 적용하여 진동 특성을 해석하고자 한다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.04a
• /
• pp.163-164
• /
• 2014

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.1130-1135
• /
• 2001

This paper investigated the dynamic performance of HDD disk-spindle system to reduce disk fluttering. Rocking frequencies of the disk-spindle system and radial NRRO are measured to escape the ball defect frequencies and to determine the relative optimal position of the disk in the motor. It was found that disk fluttering was reduced by increasing disk thickness, inserting viscoelastic material between the disk and the spacer and decreasing the gap between the disk and the base.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.05a
• /
• pp.262-263
• /
• 2010

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.10 s.181
• /
• pp.2496-2501
• /
• 2000

High speed ball end milling is attracting interest in the aerospace industry for the machining of complex 31) airfoil surfaces in nickel based superalloys, Experimental work is detailed on the effect of cutter orientation on tool life, cutting forces, chip formation, specific force and workpiece surface roughness, when high speed ball end milling nickel based supperalloy(lnconel 718). Dry cutting was performed using 8min diameter solid carbide cutters coated with either TiA1N or CrN for the workpiece mounted at an angle of 45˚ from the cutter axis. A horizontal downwards cutting orientation provided the best tool life with cut lengths~50% longer than for all other directions. Evaluation of cutting forces and associated spectrum analysis of results indicated that cutters employed in a horizontal downwards direction produced the least vibration.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.32 no.1
• /
• pp.7-11
• /
• 2012

For fault detection about the abrasion stage of rotational machineries under the dynamic loading conditions unlike the traditional diagnosis method used in the past decade, the infrared thermographic method with its distinctive advantages in non-contact, non-destructive, and visible aspects is proposed. In this paper, by applying a rotating deep-grooved ball bearing, passive thermographic experiments were conducted as an alternative way to proceeding the traditional fault monitoring on spectrum analyzer. As results, the thermographic experiment was compared with the traditional vibration spectrum analysis to evaluate the efficiency of the proposed method. Based on the results obtained as NDT, the temperature characteristics and abnormal fault detections of the ball bearing according to the abrasion stage were analyzed.

• Journal of KSNVE
• /
• v.6 no.1
• /
• pp.107-114
• /
• 1996

The damping characteristics of a cylindrical structure containing oil and bearing balls is investigated for external bending forces. The experimental data obtained through the use of bearing balls with viscous oil in a column is given and analyzed. The viscous action of the oil and inertia effects of the balls on the inside of column create a drag force. The drag force dampens the vibration of the column. This study aims to search for an optimum combination of oil and balls which would produce maximum damping. Machining oils of various viscosities along with ball bearings of various sizes place inside cantilevered aluminium tubes of various diameters to create a rig on which the damping properties of the oil and balls can be studied. The contileved tubes are studied in both horizontal and vertical positions in order to gauge the effect of gravity on the system. The actions of the ball in the column and damping characteristics are investigated according to the dimensionless terms. The Buckingham theorem is used to reduce the variables and to predict the damping of an oil ball column. Though the damping ratio remains fairly constant in the horizontal position of column, the damping ratio begins to increase as the ratio of the number of balls and column length rise above 0.28 in the vertical position of oil ball column. The ratio of the ball diameter to column diameter influences the damping ratio with an optimum diameter ratio. Slenderness ratio and gravity effects on the damping ratio ane investigated.

• Korean Journal of Applied Biomechanics
• /
• v.28 no.3
• /
• pp.187-191
• /
• 2018

Objective: The purpose of the present study is to investigate the effect of a muscle activity by applying the complex exercise method of sling in accordance with the provision of various vibration intensities for paraplegia-spinal cord injury. Method: The subjects of the study were 15 men in their 40s and 50s with lower limb disabilities and low potential risk, who were randomly divided into a sling exercise group (SG n=4), a sling with low frequency vibration group (SLVG n=4), a sling with mid-frequency vibration group (SMVG n=4), and a sling with high frequency group (SHVG n=4) in accordance with the provision of slings and vibration stimuli. The vibratory intensity provided was divided into low frequency (30 Hz), mid-frequency (50 Hz), and high frequency (70 Hz). The anterior deltoid (AD), the posterior deltoid (PD), the pectoralis major (PM), the upper trapezius (UT), the latissimus dorsi (LD), and the multifidus (MF) were measured to compare and analyze muscle activity. Results: The closed kinetic chain (CKC) exercise to the shoulder joint showed higher muscle activity in most muscles for the SMVG, and statistically significant differences in the anterior deltoid (AD), the pectoralis major (PM), and the multifidus (MF) in particular. Conclusion: The intermediate frequency (50 Hz) string vibration was the effective vibration stimuli for Closed kinetic chain (CKC) exercises.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.2
• /
• pp.70-74
• /
• 2017

Two milling methods, dry vibration milling and wet ball milling, were used to prepare $Na_{2/3}(Ni_{1/3}Mn_{2/3})O_2$ powders as a cathode material for sodium ion batteries. The morphology and electrochemical property of the two powders with different milling processes were compared to each other. The particle size is less than $1{\mu}m$ in the dry vibration milled powder, while lots of larger particles than $1{\mu}m$ were found in the wet ball milled one. The single phase of $Na_{2/3}(Ni_{1/3}Mn_{2/3})O_2$ was obtained in the temperature range of $875{\sim}900^{\circ}C$. The discharge capacity and discharge voltage of the powder prepared by the dry process were higher than those of one prepared by the wet process.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.60 no.2
• /
• pp.82-90
• /
• 2011

The small precision spindle motors in the high value-added products including the visible home appliances such as DLP projector require not only the energy conversion devices but also high efficiency, low vibration and sound operation. However, the spindle motors using the conventional ball bearing and sintered porous metal bearing have following problems, respectively: the vibration by the irregularity of balls and the short motor life cycle by the ball's abrasion and higher sound noises by dry contact between shaft and sleeve. In this paper, it is proposed that the spindle motor with a fluid dynamic bearing is suitable for the motor to drive the color wheel of the DLP(digital lightening processor) in the visible home appliances. The proposed spindle motor is composed of the fluid dynamic bearing with both the radial force and the thrust force. The fluid dynamic bearing is solved by the finite element analysis of the mechanical field with the Reynolds equations. The magnetic part of spindle motor, which is a type of Brushless DC Motor, is designed by the electro-magnetic field analysis coupled with the Maxwell equation. And the load capacity and the friction loss of fluid dynamic bearing are analyzed to bearing clearance variation by the fabrication error in designed motor. The design of the proposed motor is implemented by the load torque caused by the eccentricity and the unbalance of the fluid dynamic bearing when the motors are fabricated in error. The prototype of the motor with the fluid dynamic bearing is manufactured, and experiment results show the vibration, sound, and phase current at no load and color wheel load of the motors in comparison. The high performance characteristics with the low vibration, the low acoustic noise and the optimal mechanical structure are verified by the experimental results.