• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 추계학술대회논문집
• /
• pp.602-603
• /
• 2008

The design modification of problematic component in a given vibration path is disallowed in order to sacrifice other performances such as ride comport or handling of a vehicle. For this, the paper presents a new contribution analysis based on transmissibility ratio (TR) of acceleration in a definite vibration path to find a proper candidate for design modification. The new contribution analysis is based on the fact that the sensitivity of TR over a small design change is inversely proportional to the magnitude of TR. The new methodology can significantly relieve efforts of time-consumming modal analysis for detail modal information. The theory of proposed contribution analysis is simulated with five-degree-of-freedom open vibration path and confirms that the contribution result is well matched with the variance of TR over a dynamic change on a vibration path.

• 한국소음진동공학회논문집
• /
• 제20권11호
• /
• pp.1071-1077
• /
• 2010

The reduction of the vehicle interior noise has been the main interest of noise and vibration harshness(NVH) engineers. A passenger vehicle has various and complicated transmission paths of sound and vibration. In order to identify the mechanism of transfer path, estimation of excitation force and exact modeling of transfer path are required. This paper presents method for estimating the noise source contribution on the road noise of the vehicle in a multiple input system where the input sources may be coherent with each other. And vector synthesis technique is employed to identify the characteristics of road noise and its transmission to vehicle compartment through noise and vibration analysis. Vibration reduction efficiency of each transfer path is evaluated by comparing individual vector components obtained virtual simulation.

• 한국소음진동공학회논문집
• /
• 제15권3호
• /
• pp.280-289
• /
• 2005

A single degree of freedom system and transmissibility are key concepts in many problems of vibration isolation. In order to apply this approach, however, several assumptions must be satisfied, which are often not realistic. For examples, in practical systems, vibration transmissions at multi-point with multi-degree of freedom(translational and rotational DOF) take place and mobilities or impedances of receiver structures cannot be ignored any more especially over high frequency range. Therefore, a multi-dimensional treatment is required for accurate estimation of dynamic behavior of the system. In this paper, an approach using vibrational power flow is introduced to deal with analysis of multi-dimensional vibration isolation system in a more practical way and in aspects of vibration isolations and vibration path analysis. Procedures of this approach and some results of research for vibrational power path analysis with rotational terms included are presented. Difficulties in this method are also discussed.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.166-170
• /
• 2008

In this study, it proved that transfer path analysis is a proper technique to estimate the interior noise from comparing measured interior noise in case of 3 point supported engine mount system. And the simulation of the vibration isolation for active engine mount using FXLMS algorithm is performed. Also, it verified that reduction of estimated interior noise from transfer path analysis and simulation of the vibration isolation.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.292-293
• /
• 2014

Transfer Path Analysis is technique predicting transmitted energy through each path. Using the Transfer Path Analysis, structure-borne noise and air-borne noise can be predicted from the system. In this study, however, the Transfer Path Analysis to target only the structure-borne noise due to the noise radiated from the vibrating panel was performed. Predicted noise by the Transfer Path Analysis and measured noise by the experiment were a high correlation. We confirmed the validity of the Transfer Path Analysis through the analysis of these results, showed how to apply the Transfer Path Analysis.

• Journal of Biosystems Engineering
• /
• 제26권3호
• /
• pp.237-244
• /
• 2001

This work was intended to investigate the effect of vibration transmission paths on the ride vibration of tractor during the rotavating and transporting operations by applying the vibration path analysis method. Accelerations at the cab mounts were measured during the rotavating and transporting operations. Ride vibrations at the sear were than calculated using the measured accelerations at the cab mounts, and the frequency response functions and inertances between the seat and cab mounts, which were derived experimentally by the impact hammer test in static condition. The human sensitivity to vibration frequency was also taken into consideration for the calculation of ride vibrations at the 1/3 octave center frequencies in the frequency domain. Vibrations transmitted through rear cab mounts affected more significantly the ride vibration of tractor. The peak accelerations at the seat occurred at the frequencies of the engine and crank speed, and the frequency induced by tire lugs on the road transportation. It was found that the rear cab mounts should be improved in order to reduce the ride vibrations more effectively.

• 한국소음진동공학회논문집
• /
• 제11권9호
• /
• pp.422-430
• /
• 2001

An electric drill is a handy tool used in a machine shop, which consists of motor, gear, bearing, shaft, and case, i.e., a gear driving system. Low level vibration and noise of the electric drill can bring the assurance of the quality and reliability of the machine. The vibration sources of the electric drill should be investigated for the reduction of the vibration and noise of the system. Through the experiments in laboratory and the various signal processing procedure for the measured vibration and sound signals, the characteristics of the vibration of the electric drill are investigated. And its propagation path is sought using partial coherence function.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 춘계학술대회논문집
• /
• pp.356-360
• /
• 2007

Fuel sloshing in a vehicle fuel tank generates a reluctant low frequency noise, called slosh noise. To reduce slosh noise, whilst many approaches have used the Computational Fluid Dynamics method to first identify fuel behavior in a fuel tank, this paper applies the Transfer Path Analysis method. It is to find contribution of each transfer path from noise transfer function, vibration transfer function and acceleration. Then the final goal is to attenuate slosh noise by controlling them. To this aim, two types of models are studied. One is the decoupled model in which some of connection points of the fuel tank with the vehicle underbody are separated. The other is the modified model which is created by changing noise transfer function and acceleration from the original model. The analysis and validation test results show that the transfer path analysis can be an approach to enhancing slosh noise.

• 한국소음진동공학회논문집
• /
• 제17권8호
• /
• pp.766-770
• /
• 2007

Fuel sloshing in a vehicle fuel tank generates a reluctant low frequency noise, called slosh noise. To reduce slosh noise, whilst many approaches have used the Computational Fluid Dynamics method to first identify fuel behavior in a fuel tank, this paper applies the Transfer Path Analysis method. It is to find contribution of each transfer path from noise transfer function, vibration transfer function and acceleration. Then the final goal is to attenuate slosh noise by controlling them. To this aim, two types of models are studied. One is the decoupled model in which some of connection points of the fuel tank with the vehicle underbody are separated. The other is the modified model which is created by changing noise transfer function and acceleration from the original model. The analysis and validation test results show that the transfer path analysis can be an approach to enhancing slosh noise.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.1000-1004
• /
• 2008

As performance of medical air compressor improve, the problem of noise increased. Noise is very important to medical air compressor because most of this installed inside of building. The main goal of this paper is show TPA (Transfer Path Analysis) result for contribution analysis using PAK system. Generally, the conventional TPA method consists of two steps. First, transfer functions between output sound and sources are measured by excitation experiment. Second, transferred sound in each transfer path is generated by multiplying the transfer function and the sound source signal. Then, if the output sound synthesized from all transferred sounds doesn't give good agreement with the measured output sound (i.e., the accuracies of the transfer functions are low), setting a suitable countermeasure guideline becomes difficult. For obtaining highly accurate transfer functions, eliminating correlations among transfer functions and noise included in the measured data are necessary. In the new method with PAK system, the vibration acceleration and sound signals around the sound sources and the output sound were measured simultaneously to obtain the transfer functions when compressor was operating. By applying PAK system, a highly accurate and efficient transfer path analysis method was developed that does not require an excitation experiment.