• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.6 no.1
• /
• pp.1-16
• /
• 1996

This study was conducted at an automobile assembly line located in Kyonggi-do, Korea from January 16 to February 28, 1995. The purposes of this study were to assess worker exposures to hand-arm vibration and the performance of gloves for reduction of vibration. The exposure to vibration was measured using to the ISO 5349(1986) method. Vibration acceleration and frequency spectra for each tool were determined on-line replicating actual working conditions and analyzed together with exposure time for evaluating individual worker exposure. Eight pneumatic hand tools, 60 workers exposured to hand-arm vibration, and three pairs of gloves were involved in this study. Results are summarized as follows. 1. Dominant frequencies of vibration for all tools(n=8) measured in this study ranged from 250 Hz to 800 Hz. 2. There was no significant correleration between dominant frequencies and free running speed (p>0.05). 3. Total predicted exposure times of using impact, hammer type did not exceed 40 minutes, but metal finish task, using grinder and sander exceeded 40 minutes. Total exposure time affected significantly the frequency-weighted, 4 hr equivalent acceleration. 4. Predicted prevalence and observed exposure period data were compared in workers(n=60), according to ISO 5349. In this results, 23(50.0 %) and 24(48.07 %) persons exceeded the mean latency periods for vibration-induced white finger(VWF) at 10 % (n=46) and 50 % (n=52) standards, respectively. On the basis of ISO equation, mean latent periods for VWF were 3.23, 4.72 years at 10 %, 50 % standards, respectively. 5. Reduction of vibration by gloves was evaluated. Since impact pneumatic tools produced low frequency vibrations, conventional gloves did not provide any protection. Gloves A and C amplify somewhat the signal at frequency below 400 Hz; the attenuation increases progressively by frequency to reach 18 dB ($7.94{\times}10^{-6}m/s^2$) at 1,000 Hz, slightly worsening Glove B did not provide any protection and made the situation slightly worse. However, since they make the hands warm, the occurrence of vibration-induced white fingers may be reduced.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.11 no.7
• /
• pp.267-274
• /
• 2001

This paper introduces experimental results related to the vibration ride conditions that a korean male subject experienced in the nationwide railway trains and the express bus. Two types of railway train's Saemaulho and Mugunghwaho. and the express bus were chosen to measure how much the whole-body vibrations on the contact area of the back , hip and feet are exposed to the subject. Measured vibration signals were analysed to assess the rife conditions quantitatively and qualitatively. Analysed results are illustrated to unveil how much typical public transportation system in Korea expose whole-body vibration to passengers. Futhermore, the performance evaluation of their seats were carried out to examine their effectiveness in reducing vibration exposure to passengers.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.1032-1037
• /
• 2003

This work measured the hand-transmitted vibration due to shipyard worker's grinding and assessed the vibration exposure for predicted 10% prevalence of vibration-induced white finger in a group of exposed persons according to test procedure of ISO 5349-1. And also the transmissibility performance of resilient material, mainly applied to anti-vibration gloves in present market was measured on the basis of ISO 13753 and confirmed that the material would Probably not provide greater attenuation below 30㎐, the dominant frequency range of hand-transmitted vibration due to grinder.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.12 s.105
• /
• pp.1327-1331
• /
• 2005

This Paper addresses what amount of whole-body vibration is exposed to Korean pilots of UH60 helicopters during their mission flight. To measure the expose4 whole-body vibration, the 12-axis whole-body vibration measurement system was used. It enables the direct measurement of whole-body vibration exposed from the body contact area consisting of the feet, hip and back. The measured 12-axis vibration signals were used to evaluate the vibration comfort level experienced by the pilots of UH60 helicopters. The evaluated vibration comfort level is found to be closeto 0.74-0.79m/s, which is equivalent to the semantic scale of 'fairly uncomfortable'. To assess the health effects of whole-body vibration exposed to Korean pilots of UH60 helicopters during their mission flight, the rms-based and VDV(vibration dose value)-based evaluation schemes, recommended by ISO 2631-1:1977, were exploited in this work. The evaluated results indicate that Korean pilots cannot avoid the fatigue-decreased proficiency limit after two-hour continuous flight. The whole-body vibration level exposed from the UH60 helicopters during continuous 10-hours mission flight is found to reach to the vibration exposure limit.

• Journal of the Ergonomics Society of Korea
• /
• v.32 no.4
• /
• pp.309-319
• /
• 2013

Objective: The aim of this study is to review and summarize human vibration measurement process, and necessity and methods of frequency weightings for human vibration. Background: Prolonged human exposure to hand-arm vibration and whole-body vibration can result in a range of adverse conditions and the development of occupational diseases such as vibration white finger. For preventing these adverse effects, it is important to correctly apply human vibration measurement process. Method: This manuscript was based on the review and summary of mechanical and human vibration relevant texts, academic papers, materials obtained through web surfing. Results: This manuscript summarizes human vibration measurement process described in ISO standards and relevant texts. The sensitivity of the human body to mechanical vibration is known to be dependent on both the frequency and direction of vibration. To take this into account, varying frequency weighting functions have been developed, and RMS frequency-weighted accelerations are used as the most important quantity to evaluate the effects of vibration on health. ISO provided nine frequency weighting functions in the form of curves and tables. Researches on frequency weightings are focused on development and validation of new frequency weightings to truly reflect the relationship between vibration exposure and its adverse effects. Application: This would be useful information for systematically applying human vibration measurement and analysis process, and for selecting appropriate frequency weighting functions.

• IE interfaces
• /
• v.17 no.3
• /
• pp.375-383
• /
• 2004

The purpose of this study is to investigate the characteristics of vibration induced by the powered hand tools used in the automobile assembly lines, and estimate the prevalence of vibration syndrome. The acceleration levels of four major powered hand tools were measured using the ISO 5349 method along with the time of exposure to the vibration of the hand tools. Four-hour-energy-equivalent frequency-weighted accelerations ranged from $1.27m/s^2$ to $2.58m/s^2$, After exposure to vibration for 12.6 years, about 10% of the workers using impact ranches were expected to develop Raynaud's disease. For the workers using grinders, 16.6% of the workers were expected to develop Raynaud's disease. The results would be of help in developing the guidelines of local vibration control.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.131-133
• /
• 2014

Vibration exposure of the KTX and ITX-saemaeulho on the Gyung-Bu line was evaluated and compared in terms of human health based on ISO 2631. RMS value of KTX was calculated as much lower than ITX-saemaeulho in all travel sections. When VDV result of the two trains drived return travel from Seoul to Busan in single day is compared on the health guidance caution zone of ISO 2631, vibration exposure of KTX is safer than ITX-saemaeulho which is marginally under the caution line.

• Journal of KSNVE
• /
• v.10 no.2
• /
• pp.299-305
• /
• 2000

In this study, the characteristics of transmitted vibration on hand-arm system are examined when operating electric hand tools. Also through the correlation analysis between anthroponetric data and transmitted vibration, and comparison study with appropriate amount of work done based on the ISO criteriaa, the basic data for the ergonomic work design can be presented. The types of electric tools and works for the experiment are drill (general type and impact type), grinder, wire brush and steel to analyze the characteristics of transmitted vibrations, the amount of transmitted vibrations in X, Y and Z direction at tool(T), hand(H), wrist(W), and the joint between foream and upper arm(A) were measured at the frequency range of 6.3∼1000[HZ]. Also, the limit of human exposure to vibration, and the response of frequency were conducted.

• Smart Structures and Systems
• /
• v.13 no.6
• /
• pp.959-974
• /
• 2014

Hand-Arm Vibration Syndrome (HAVS) is a group of diseases caused by exposure of the hands to vibration while operating the hand held power tools such as road breaker, drilling machine, demolition hammer in construction works. In this paper, area-changed capacitive micro-accelerometer is designed to measure the vibration exposure on worker's hand when operating a drilling machine on various blocks such as clay block, paver block and solid cement block. The design process includes mathematical modelling of micro-accelerometer and simulations are done using INTELLISUITE 8.6. Experimental results are taken for various blocks surfaces using conventional and micro-accelerometer. Comparisons show that usage of area-changed micro-accelerometer for Hand-arm vibration monitoring provides better sensitivity, which in turn reduces the risk of HAVS in workers.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.9
• /
• pp.831-840
• /
• 2013

The noise levels of workers in tunnel sites are likely to be high because tunneling work places are confined space. However, research on the noise exposure levels of tunneling workers have not been performed intensively due to restricted accessibility to tunnel construction sites. The aim of this study is to evaluate the noise exposure levels for workers engaged in tunneling work sites. Noise dosimeters were used for monitoring workers' noise exposure level in 5 tunneling work sites in accordance with the Notification of the Ministry of Labor. Among 5 tunneling work sites, 4 of them used NATM tunneling method and 1 work site used shield TBM tunneling method. The average noise exposure levels of NATM tunneling workers was 81.1 dB(A) and 15.4 % of the workers' noise level were exposed more than 90 dB(A) which is the exposure limit value. In Shield TBM tunneling method, 4.3 % of the workers were exposed more than 90 dB(A) of noise level, the average noise exposure levels of TBM tunneling workers was 84.1 dB(A).