• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.3
• /
• pp.191-197
• /
• 2016

The shaft system of a vessel becomes stiffer because of larger engine power, whereas the hull structure becomes more flexible because of scantling optimization conducted by using high-tensile thick steel plates. The draught-dependent deformation of the hull affects each bearing offset and reaction force comprising the subsequent shaft system. This is the reason that more sophisticated shaft alignments are required. In this study, an FE analysis performed under the expected operating conditions of two (2) vessels, as maximum draught change and to analyze the shaft alignment using the relative bearing offset change, which was derived from an FE analysis of the 50,000 DWT oil/chemical tanker, which has become an eco-friendly vessel in recent years. Based on this, the influence of the hull deflection on the bearing offset was reviewed against results for shaft alignment conditions.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.18 no.4
• /
• pp.292-303
• /
• 1998

Recent study has demonstrated that some magnetic properties are sensitive to the microstructural state of material. The ASTM A 508 Gr. 3 reactor pressure vessel steel has various microstructural changes including martensitic and bainitic phases, and various sizes of grain and precipitates in the weld heat-affected zone (HAZ). To correlate the microstructural state with Barkhausen noise (BN), specimens were prepared through simulating various weld thermal cycles using a thermal simulator. The conventional magnetic properties, i.e. coercive force, remanence and maximum induction, did not change significantly, whereas the BN amplitude and energy during a magnetization cycle changed markedly with microstructural state. The BN increased with increasing grain and carbide sizes, and the tempered bainite structure showed higher BN parameter than tempered martensite.

• Computers and Concrete
• /
• v.14 no.2
• /
• pp.127-143
• /
• 2014

LOCA (Loss Of Coolant Accident) is one of the most important utmost accidents for Prestressed Concrete Containment Vessel (PCCV) due to its coupled effect of high temperature and inner pressure. In this paper, heat conduction analysis is used to obtain the LOCA temperature distribution of PCCV. Then the elastic internal force of PCCV under LOCA temperature is analyzed by using both simplified theoretical method and FEM (finite element methods) method. Considering the coupled effect of LOCA temperature, a nonlinear elasto-plasitic analysis is conducted for PCCV under utmost internal pressure considering three failure criteria. Results show that the LOCA temperature distribution is strongly nonlinear along the shell thickness at the early time; the moment result of simplified analysis is well coincident with the one of numerical analysis at weak constraint area; while in the strong constrained area, the value of moments and membrane forces fluctuate dramatically; the simplified and numerical analysis both show that the maximum moment occurs at 6hrs after LOCA.; the strain of PCCV under LOCA temperature is larger than the one of no temperature under elasto-plastic analysis; the LOCA temperature of 6hrs has the greatest influence on the ultimate bearing capacity with 8.43% decrease for failure criteria 1 and 2.65% decrease for failure criteria 3.

• Journal of the Society of Naval Architects of Korea
• /
• v.52 no.6
• /
• pp.485-493
• /
• 2015

Planing hull form is widely used as a high speed vessel hull. There is a problem of the planing hull not solved yet. The problem is that the planing hull has very large vertical acceleration and large heave and pitch motions. As one method for overcoming this problem, there is "wave-piercing hull". Before the motion in waves is investigated, the resistance and running attitude must be investigated. In this paper, the running attitude and resistance of two wave-piercing hulls are investigated by model tests. Model test results show that the wave-piercing hulls have large trim angle and sinkage at the high speed, so additional model tests are conducted by using the hull appended by stern interceptor that is very thin plate to increase the hydrodynamic pressure at the attached location. The results are compared with other planing hulls and the resistance components and the hydrodynamic force are discussed. From the model test results, it can be known that the stern interceptor is the effective appendage for the reduction of the resistance and trim angle of wave-piercing hull.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.53 no.4
• /
• pp.446-455
• /
• 2017

The improvement of resistance performance for the 4.99 ton class fishing boats was shown. The 4.99 ton fishing boats are the most commonly used one in the Korean coastal region. The evaluation of resistance performance was estimated by the Computational Fluid Dynamics (CFD) analysis. The CFD simulation was performed by the validation for various types of bow shapes on the hull. The optimized hull form from the simulation was selected and showed the best resistance performance. This hull type was tested on the towing tank in the National Institute of Fisheries Science (NIFS). The effective horsepower (EHP) was estimated by the resistance test on the towing tank with the bare hull condition. The drag force on the three service speed conditions was obtained for the resistance analysis to power prediction. The measured drag forces are compared with the results from the CFD simulation with one another. As results of the model tests, it was confirmed that the shape of the bow is an important factor in the resistance performance. The effective horsepower decreased about 30% in comparison with the conventional hull form. Also, the resistance performance improved the reduction of required horsepower, which especially contributed to the energy-saving for the fisheries industry. In the CFD analysis, the resistance performance improved slightly. In this case, the ratio of the residual resistance ($C_R$) in the total resistance ($C_T$) was high. Therefore, the CFD analysis was not enough to satisfy with reflection for the free surface and wave form in the CFD procedure. Both model test and CFD calculation in this study can be applied to the initial design process for the coastal fishing vessel.

• Journal of Navigation and Port Research
• /
• v.42 no.2
• /
• pp.127-136
• /
• 2018

The motion response of floating structures is of significant concern in marine engineering. Floating structures can be disturbed by waves, winds, and currents that create undesirable motions of the vessel, therefore causing challenges to its operation. For a floating structure, mooring lines are provided in order to maintain its position; these should also produce a restoring force when the vessel is displaced. Therefore, it is important to investigate the tension of mooring lines and the motion responses of a twin barge when moored to guarantee the safety of the barge during its operation. It is essential to precisely identify the characteristics of the motion responses of a moored barge under different loading conditions. In this study, the motion responses of a moored twin barge were measured in regular waves of seven different wave directions. The experiment was performed with regular waves with different wavelengths and wave directions in order to estimate the twin-barge motions and the tension of the mooring line. In addition, the motion components of roll, pitch, and heave are completely free. In contrast, the surge, sway, and yaw components are fixed. In the succeeding step, a time-domain analysis is carried out in order to obtain the responses of the structure when moored. As a result, the Response Amplitude Operator (RAO) motion value was estimated for different wave directions. The results of the experiment show that the motion components of the twin barge have a significant effect on the tension of the mooring lines.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.11a
• /
• pp.92-97
• /
• 2000

Low-velocity impact damage of a thick pressure vessel by composite materials was studied using the modified Herzian contact radius theory. Impactors of various masses and various tup shapes were dropped freely in the range of 20m to 200mm height. With acceleration gage and strain gage installed on the impactor, impact force and acceleration and Contact radius were measured. After a test, the samples were radiographed to scan the state of damage. Compared with hemispherical tup of 12.7mm diameter, the contact radius of hemispherical tup of 25.4mm diameter was bigger. And the experimental data and the theoretical data was different due to the mechanical properties difference. The acceleration value was changed linearly according to the height.

• Journal of Navigation and Port Research
• /
• v.36 no.8
• /
• pp.607-612
• /
• 2012

In this paper, calculation methods of resistance of the ship to be towed and towline tension are discussed. When the vessel is fallen into dead ship condition then appropriate towing force have to be estimated to move the vessel from accident place to safe area. In this research, resistance of the ship to be towed and the tow hawser were considered to estimate total towline tension. Polynomial interpolation method is also applied to estimate additional hydrodynamic resistance of towline. Finally, UI program to calculate the resistance and total towline tension is developed. The developed program based on the research results is effective and convenient to use.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.50 no.3
• /
• pp.396-406
• /
• 2014

Shrimp beam trawl fishery is one of the important coastal fisheries in Korea. It has a regulation to the length of beam (8m) and wing net (7m) of shrimp beam trawl that has been used in the district of Junlanam-do and Gyungsangnam-do. This regulation was made in relation to the size of shrimp beam trawler of 3-ton class at that time. Now the shrimp beam fishing vessel has a limit not greater than 5 tons in gross ton. Recently, with improvement of fishing industry and fishing vessel fishermen asked the expansion of the length of beam and wing net, therefore it is necessary to investigate the effect of lengthening the beam and wing net length. Three different beams (8m, 10m and 12m in length) and three different wing net (7m, 10m and 13m in length) were made and the experiment was conducted near Narodo of Goheng by two fishing vessels of 4.98 and 4.88 tons in gross ton between June 2011 and October 2012. When the length of wing net was increased from 7m to 10m and 13m, the relative catch ratio in total biomass was increased 25% and 79% for shrimp, (17% and 22% in total), respectively. And when the beam length was increased from 8m to 10m and 12m, the relative catch ratio was increased 35% and 84% for shrimp, (21% and 37% in total), respectively. The force exerted to the iron guide of inhauler's with the beam length of 8m was about 30% greater than that with the beam length of 10m when hauling the shrimp beam trawl net.

• Journal of the Society of Naval Architects of Korea
• /
• v.59 no.5
• /
• pp.252-261
• /
• 2022

The present study concerns assessing the operability of a surface combatant, based on the Percent-Time-Operable (PTO). For validation of the seakeeping analysis in the regular waves, the model test is first conducted in a towing tank. The seakeeping analysis results in the regular waves are expanded to the irregular waves, considering the wave spectra around the Korean peninsula and in North Pacific. The seakeeping criteria of the surface combatant in transit, combat, replenishment operation, and survival condition are defined by the literature review. An annual operation scenario of the surface combatant in two operation areas, i.e., advance speed and wave direction, are combined with the seakeeping analysis results to assess PTO. The main constraints of operability of the surface combatant are identified as the pitch angle and vertical velocity at the helicopter deck.