• Journal of Korea Water Resources Association
• /
• v.32 no.2
• /
• pp.153-162
• /
• 1999

In this study, mixing and dilution characteristics of vertical multijet discharged by multiport diffuser into stagnant water are investigated. The results obtained from the experiment of multiport diffuser performed in the three dimensional flume are as follows. As far as merging process of multiport diffuser is concerned, merging starts at about z/l = 3 although merging length is dependent upon stability condition and thereafter lateral temperature distribution becomes gradually uniform which is typical distribution of plane jet. Analyses of experimental data for minimum dilution show that characteristics of minimum dilution are described based on three regions which are jet region where momentum is dominated, intermediate region, and plume region where buoyancy is dominated. Minimum dilution coefficient in plume region of multiport diffuser obtained in this study is 15% higher than that of plane diffuser. This is because individual jet of multiport diffuser entrains more ambient water before merging is occurred, and therefore dilution increases.

• Journal of Korean Society of Water and Wastewater
• /
• v.30 no.2
• /
• pp.187-196
• /
• 2016

In this study, a newly developed agitator with hydrofoil impeller applied to actual biological process in advanced wastewater treatment plant was evaluated. Several series of experiments were conducted in two different wastewater treatment plants where actual problems have been occurred such as the production of scums and sludge settling. For more effective evaluation, computational fluid dynamics (CFD) and measurements of MLSS (Mixed Liquor Suspended Solids) and DO (Dissolved Oxygen) were used with other measuring equipments. After the installation of one unit of vertical hydrofoil agitator in plant A, scum and sludge settling problems were solved and more than seventy percent of operational energy was saved. In case of plant B, there were three cells of each anoxic and anaerobic tanks, and each cell had one unit of submersible horizontal agitator. After the integration of three cells to one cell in each tank, and installation of one vertical hydrofoil agitator per tank, all the problems caused by improper mixing were solved and more than eighty percent of operational energy was found to be saved. Simple change of agitator applied to biological process in wastewater treatment plant was proved to be essential to eliminate scum and sludge settling problems and to save input energy.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.15 no.4
• /
• pp.115-124
• /
• 2007

The material compressions in the vertical composting reactor affect to the biodegradation rates of the organic wastes. This study investigated the variations of physical properties of the composting materials according to the height of reactor due to affect to the settlement in the vertical composting reactor. The variations of decreased temperature after peak temperature showed the different patterns depending on the reactor heights. The variation width of re-increased temperature after peak temperature was reduced as the mixing operations were increased, and increased as the height of reactor elevated. The moisture content and the variation width of the moisture content were increased higher as the height of the reactor became higher. The variations of the bulk density at each height of vertical reactor showed the same tendency comparing with those of the moisture content. The relationship between bulk density and moisture content had shown the quadratic equation (r2=0.94). The dry solid contents at each reactor height were decreased as the height of reactor were increased. The results of the variation of the physical properties during the composting process were caused by the downward compression of the material into the reactor. Settlement rate in the vertical composting reactor was estimated about 2.184cm/day. To increase the biodegradation efficiency in the vertical reactor, the conditions of air path in the composting material matrix have to be investigated afterwards.

• Ocean and Polar Research
• /
• v.30 no.3
• /
• pp.261-275
• /
• 2008

The profile of a fixed site at station M ($34.77^{\circ}N,\;129.13^{\circ}E$) in the Korea Strait was studied from March 2006 to February 2007. The aim was to understand the relationship between the annual thermal stratification pattern and seasonal variation in phytoplankton community structure. Physicochemical factors including temperature, salinity and nutrient concentrations, which strongly influence the proliferation and diversity of phytoplankton, were measured. The study period was divided into three due to the characteristic of thermohaline structures; mixed I (March-May 2006), stratified (June-November 2006) and mixed II(December 2006-Feburuary 2007). Diatoms dominated during the mixed I (89%) and II (48%) periods, while nanoplankton group occupied over 83% of total population during the stratified period. The dominant species during the mixed I and II was Chaetoceros socialis (47% and 29%, respectively), while during the stratified period Gyrodinium sp.(4%) was the most dominant. Averaged total chl a concentrations during the mixed I and II periods were 0.61 mg $m^{-3}$ and 0.72 mg $m^{-3}$, respectively, which were at least two-fold higher than that during the stratified period (0.30 mg $m^{-3}$). The vertical mixing and convection process of the water column induced nutrient supply from the bottom layer to the euphotic zone. It also led to the dominance of diatoms during the mixed periods, whereas small phytoplankton prevailed over large phytoplankton as stratification blocked the upward movement of nutrients to subsurface during the stratified period. During the mixed I and II periods, microplanktonic chl a dominated concentrations (50% and 48%, respectively), while picoplanktonic chl a occupied over 37% of total chl a during the stratified period.

• Journal of Powder Materials
• /
• v.14 no.5
• /
• pp.281-286
• /
• 2007

Ordered $L1_0$ to FePt nanoparticles are strong candidates for high density magnetic data storage media because the $L1_0$ phase FePt has a very high magnetocrystalline anisotropy $(K_u{\sim}6.6-10{\times}10^7erg/cm^3)$, high coercivity and chemical stability. In this study, the ordered $L1_0$ FePt nanoparticles were successfully fabricated by chemical vapor condensation process without a post-annealing process which causes severe particle growth and agglomeration. The $Fe_{50}Pt_{50}$ nanopowder was obtained when the mixing ratio of Fe(acac) and Pt(arac) was 2.5 : 1. And the synthesized FePt nanoparticles were very fine and spherical shape with a narrow size distribution. The average particle size of the powder tended to increase from 5 nm to 10 nm with increasing reaction temperature from $800^{\circ}C$ to $1000^{\circ}C$. Characterisitcs of FePt nanopowder were investigated in terms of process parameters and microstructures.

• Korean Journal of Materials Research
• /
• v.17 no.4
• /
• pp.207-214
• /
• 2007

We fabricated thermally-evaporated 10 -Ni/(poly)Si and 10 -Ni/1 -Ir/(poly)Si structures to investigate the microstructure of nickel monosilicide at the elevated temperatures required for annealing. Silicides underwent rapid at the temperatures of 300-1200 for 40 seconds. Silicides suitable for the salicide process formed on top of both the single crystal silicon actives and the polycrystalline silicon gates. A four-point tester was used to investigate the sheet resistances. A transmission electron microscope(TEM) and an Auger depth profile scope were employed for the determination of vertical section structure and thickness. Nickel silicides with iridium on single crystal silicon actives and polycrystalline silicon gates shoed low resistance up to 1000 and 800, respectively, while the conventional nickle monosilicide showed low resistance below 700. Through TEM analysis, we confirmed that a uniform, 20 -thick silicide layer formed on the single-crystal silicon substrate for the Ir-inserted case while a non-uniform, agglomerated layer was observed for the conventional nickel silicide. On the polycrystalline silicon substrate, we confirmed that the conventional nickel silicide showed a unique silicon-silicide mixing at the high silicidation temperature of 1000. Auger depth profile analysis also supports the presence of thismixed microstructure. Our result implies that our newly proposed iridium-added NiSi process may widen the thermal process window for the salicide process and be suitable for nano-thick silicides.

• Journal of the korean society of oceanography
• /
• v.39 no.1
• /
• pp.72-95
• /
• 2004

The Yellow Sea is characterized by relatively shallow water depth, varying range of tidal action and very complex coastal geometry such as islands, bays, peninsulas, tidal flats, shoals etc. The dynamic system is controlled by tides, regional winds, river discharge, and interaction with the Kuroshio. The circulation, water mass properties and their variability in the Yellow Sea are very complicated and still far from clear understanding. In this study, an effort to improve our understanding the dynamic feature of the Yellow Sea system was conducted using numerical simulation with the ROMS model, applying climatologic forcing such as winds, heat flux and fresh water precipitation. The inter-annual variability of general circulation and thermohaline structure throughout the year has been obtained, which has been compared with observational data sets. The simulated horizontal distribution and vertical cross-sectional structures of temperature and salinity show a good agreement with the observational data indicating significantly the water masses such as Yellow Sea Warm Water, Yellow Sea Bottom Cold Water, Changjiang River Diluted Water and other sporadically observed coastal waters around the Yellow Sea. The tidal effects on circulation and dynamic features such as coastal tidal fronts and coastal mixing are predominant in the Yellow Sea. Hence the tidal effects on those dynamic features are dealt in the accompanying paper (Kim et at., 2004). The ROMS model adopts curvilinear grid with horizontal resolution of 35 km and 20 vertical grid spacing confirming to relatively realistic bottom topography. The model was initialized with the LEVITUS climatologic data and forced by the monthly mean air-sea fluxes of momentum, heat and fresh water derived from COADS. On the open boundaries, climatological temperature and salinity are nudged every 20 days for data assimilation to stabilize the modeling implementation. This study demonstrates a Yellow Sea version of Atlantic Basin experiment conducted by Haidvogel et al. (2000) experiment that the ROMS simulates the dynamic variability of temperature, salinity, and velocity fields in the ocean. However the present study has been improved to deal with the large river system, open boundary nudging process and further with combination of the tidal forcing that is a significant feature in the Yellow Sea.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.12
• /
• pp.996-1002
• /
• 2000

Ferroelectric (Ba, Sr) TiO$_3$(BST) thin films have attracted much attention for use in new capacitor materials of dynamic random access memories (DRAMs). In order to apply BST to the DRAMs, the etching process for BST thin film with high etch rate and vertical profile must be developed. However, the former studies have the problem of low etch rate. In this study, in order to increase the etch rate, BST thin films were etched with a magnetically enhanced inductively coupled plasma(MEICP) that have much higher plasma density than RIE (reactive ion etching) and ICP (inductively coupled plasma). Experiment was done by varying the etching parameters such as CF$_4$/(CF$_4$+Ar) gas mixing ratio, rf power, dc bias voltage and chamber pressure. The maximum etch rate of the BST films was 170nm/min under CF$_4$/CF$_4$+Ar) of 0.1, 600 W/-350 V and 5 mTorr. The selectivities of BST to Pt and PR were 0.6 and 0.7, respectively. Chemical reaction and residue of the etched surface were investigated with X-ray photoelectron spectroscopy (XPS) and secondary ion mass spectroscopy (SIMS).

• Ocean and Polar Research
• /
• v.37 no.2
• /
• pp.149-159
• /
• 2015

The Southern Ocean (SO) plays a primary role in global climate by storing and transporting anthropogenic carbon dioxide through the meridional overturning circulation and the biological pumping process. In this study, we aim to investigate interannual variability of summer chlorophyll concentration in the SO and its relation with the El $Ni{\tilde{n}}o$ Southern Oscillation (ENSO), using satellite ocean color data covering 16 years from 1997 to 2012. During El $Ni{\tilde{n}}o$ periods, chlorophyll concentration tends to increase in the subtropics (north of the subantarctic front). This chlorophyll increase is likely linked to El $Ni{\tilde{n}}o$-induced surface cooling that increases nutrient supply through enhanced vertical mixing in the subtropics. On the other hand, the subpolar gyres show localized chlorophyll changes in response to the ENSO. The localized response seems to be primarily attributed to changes in sea-ice concentrations. Our findings suggest that ENSO contributes interannual variability of chlorophyll in the SO through different mechanisms depending on regions.

• Journal of Environmental Science International
• /
• v.23 no.2
• /
• pp.249-259
• /
• 2014

This paper investigates the characteristics of high $PM_{2.5}$ episodes occurred at Anmyeondo area in spring time, 2009. The monthly mean $PM_{2.5}$ concentration during April was the highest in the year and especially, high levels of $PM_{2.5}$ exceeding standard regulation level were sustained consecutively during 5 to 13 April. To analyze more detailed $PM_{2.5}$ characteristics, numerical simulations were carried out using CMAQ(Community Multi-scale Air Quality) with IPR(Integrated Process Rate) and DDM-3D(Decoupled Direct Method). $PM_{2.5}$ level was lower in daytime than that in nighttime due to vigorous vertical mixing during daytime. The chemical composition was showed that ratio of primary ion components such as sulfate($SO_4{^{2-}}$), nitrate($NO_3{^-}$) and ammonium($NH_4{^+}$) were nearly half of total amount of $PM_{2.5}$. Aerosol and transport process dominantly contributed to $PM_{2.5}$ concentration in Anmyeondo area and contribution rate of local emissions was nearly zero since Anmyeondo area has rare anthropogenic PM emission sources. DDM-3D analysis result showed that $PM_{2.5}$ in Anmyeondo area was influenced by emissions from Shanghai and Shandong region of China.