• Physical Therapy Korea
• /
• v.9 no.3
• /
• pp.39-46
• /
• 2002

In this study, vertical acceleration of center of mass was observed along normal gait phases in 9 healthy male volunteers (aged $25.7{\pm}2.18$). The developed wireless accelerometric device was attached on the intervertebral space between L3 and L4 using a semi-elastic waist belt. A three-dimensional motion analysis system, synchronized with the accelerometry, was used for detecting gait phases. There was no significant correlation between the body weight and the acceleration. The first peak curve covered loading response phase. The second downward peak point was matched accurately with the opposite toe-off. In mid-stance and terminal stance, the acceleration curve highly resembled the vertical ground reaction force curve. There was no significant difference in timing between the final upward peak point and the initial contact. Therefore, the developed accelerometry system would be helpful in determining determine temporal gait pattems in patients with gait disorders.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.10
• /
• pp.5268-5273
• /
• 2013

Technique for analyzing pile installed by vibratory pile driver was developed and results of analysis obtained from variation of bias weight were studied. It can be seen from load transfer curve for dynamic skin friction that load transfer curve shift to downward as bias weight increases. Shape of load transfer curve for dynamic skin friction becomes closer to shape of coil as the bias weight decreases. Magnitudes of toe resistances were not affected by the bias weight. Shape of load transfer curve for dynamic toe resistance shows the similar tendency as the load transfer curve for skin friction exhibits. Vertical displacement increases as the bias weight increases and the shape of vertical displacement with time shows more distinct shape of wave.

• Journal of KSNVE
• /
• v.8 no.6
• /
• pp.1015-1022
• /
• 1998

This paper addresses the results of an experimental and analytical research of a helical coil spring subjected to dynamic behavior using space curve vector after considering elongation rate. Vibrations in helical coil spring can be divided into 3 modes such as vibrations of coil spring center axis' vertical direction. axis' horizontal direction, direction about center axis. However. these 3 modes are dependent one another and are characterized as coupled. The dependency was proved through both theoretically and experimentally analyzing the results of dynamic characteristics of coil spring center axis' vertical direction vibration by transfer matrix method using the governing equation of static equilibrium. Also this paper shows that pitch angle and active coils in coil spring affect the dynamic spring characteristics of the above 3 modes and are especially sensitive to the mode for vibration of axis' horizontal direction which most affects especially on dynamo stability of helical coil spring.

• International Journal of Highway Engineering
• /
• v.18 no.4
• /
• pp.77-82
• /
• 2016

PURPOSES : This paper proposes a reliability index for the safety evaluation of freeway sections. It establishes a reliability index as a safety surrogate on freeways considering speeds and speed dispersions. METHODS : We collated values of design elements including radii, curve lengths, vertical slopes (absolute values), superelevations, and vertical slopes from seven freeway sections in Korea. We also collected data about driving speeds, traffic accidents, and their deviations. We established a reliability index using these variables. RESULTS : The average radii, curve lengths, and superelevations are highly correlated with the incidence of traffic accidents. Deviations in radius and curve lengths show an especially high correlation. The reliability index, derived from speed and speed dispersions of the seven freeway sections, also correlated highly with accidents with a correlation index of 0.63. CONCLUSIONS : Since the reliability index obtained from speed and speed dispersions are highly correlated with traffic accidents, we conclude that a reliability index can be a safety surrogate on freeways considering speeds and speed dispersions together in terms of design and operational levels.

• 유체기계공업학회:학술대회논문집
• /
• 2001.11a
• /
• pp.216-220
• /
• 2001

Flow analysis was carried out for two vertical pumps. The geometrical difference of two pumps is the adoption of vaned diffuser. Full pump models were used to simulate the velocity fields of the pumps. Pump head and velocity field were compared to obtain the features of diffuser flow. It was shown that the discontinuity of head curve was predicted and reverse flow could be generated at impeller exit even in the rated flow condition.

• Journal of Korean Society of Transportation
• /
• v.25 no.5
• /
• pp.79-90
• /
• 2007

In determining vertical grades in highway alignment design, engineers usually consider heavy vehicle performances on the upgrade. Heavy vehicles usually experience speed reduction on the upgrade and with recent years weight/horsepower improvements for heavy vehicles the speed reduction shows some change. However, in spite of the weight to horsepower improvements for the design vehicles from 300lb/HP to 200lb/HP in the AASHTO, there was no change in the maximum vertical grades. Therefore, a review of the maximum vertical grade reflecting existing heavy vehicle performances is required. In particular, in South Korea where highways pass through lots of mountaineous terrain, the maximum vertical grades must be reviewed throughly. In this study the amount of heavy vehicle performances during past decades were investigated and their expected impacts on highway vertical alignment designs were subsequently analyzed. A worldwide terrain analysis and international design standards were compared to set South Korean vertical grade standards. Traffic flow simulation Vissim was utilized to simulate vehicular flows on the upgrade and new truck performance curves on the grades were developed. Based on the new curve, it was decided that $1{\sim}2%$ increase of the maximum vertical grades could be allowed.

• Steel and Composite Structures
• /
• v.16 no.2
• /
• pp.117-133
• /
• 2014

Natural vibration of truss cable structures is analyzed based upon the general structural analysis software ANSYS, energy variational method and Rayleigh method, the calculated results of three methods are compared, from which the characteristics of free-vibration are obtained. Moreover, vertical seismic response analysis of truss cable structures is carried out via time-history method. Introducing three natural earthquake waves calculated the results including time-history curve of vertical maximal displacement, time-history curve of maximal internal force. Variation curve of maximal displacement of node along span, and variation curve of maximal internal force of member along span are presented. The results show the formulas of frequencies for truss cable structures obtained by energy variational method are of high accuracy. Furthermore, the maximal displacement and the maximal internal force occur near the 1/5 span point. These provide convenient and simple design method for practical engineering.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.6
• /
• pp.108-113
• /
• 2007

This study aims to find equivalent comfort contours, reciprocal of frequency weighting curves, for vertical steering wheel vibration. Psychophysical responses were measured from twelve male subjects by using magnitude estimation of relative discomfort due to vertical steering wheel vibrations of magnitude of 0.1 to 1.58 $m/s^2$ in the frequency range of 4 to 250 Hz. Relative discomfort were estimated with a reference vibration of 0.4 $m/s^2$ at 31.5 Hz. Equivalent comfort contours were produced from the median of sensation magnitudes judged by twelve subjects, which showed variation in the shapes with increase of vibration magnitude. A shape of the contour came close to the perception threshold curve with decrease of vibration magnitude. When the vibration magnitude increases, the shape changed close to those in the references of Hong and et al (2003). It is also recommended frequency weighting curves for vertical steering wheel vibration must be expressed as a function of vibration magnitude as well as frequency.

• Journal of the Korean Society for Railway
• /
• v.15 no.2
• /
• pp.172-178
• /
• 2012

Superimposition of vertical and transition curves is not allowed for all types of tracks in Korean regulation of railway construction. However, this criterion has been established on the basis of difficulty of maintenance of the ballasted track. Comparing with the ballasted track, the concrete slab track has the advantage of maintenance and structural, which allows the superimposition of vertical and transition curves when it satisfies the criteria of running safety and riding comfort. In this study, running safety, ride comforts and track acting forces were analyzed and compared by numerical analysis using VAMPIRE program when the vertical and transition curves are superimposed for the ballasted track as well as the concrete slab track. From the analysis results, it was found that running safety, riding comforts and track acting forces in case of superimposition of vertical and transition curves for the both tracks meet all of the criteria. Therefore, although superimposition of vertical and transition curves for the ballasted track is not allowed because of a lot of maintenance works, it can be applied to the concrete slab track considering the advantage of maintenance and structural safety.

• Journal of the Korean Society for Railway
• /
• v.16 no.4
• /
• pp.311-317
• /
• 2013

In railway construction, superimposition of horizontal and vertical curves has critical effects on the running stability and the ride comfort of vehicles as well as on construction costs. In this study, running safety, ride comfort, and track acting forces were analyzed by a numerical analysis using the VAMPIRE program according to cases of superimposition of vertical and horizontal curves. From the analysis results, it was found that running safety, riding comfort, and track acting forces in the case of superimposition of vertical and horizontal curves as well as vertical and transition curves meet all of the criteria. Also, in the case of the superimposition of vertical curves and curvature change between horizontal transition curves and circular curves meet all of the criteria.