• Structural Engineering and Mechanics
• /
• 제35권1호
• /
• pp.67-82
• /
• 2010

The beam string structure (BSS) has been widely applied in large span roof structures, while no analytical solutions of BSS were derived for it in the existing literature. In the first part of this paper, calculation formulas of displacement and internal forces were obtained by the Ritz-method for the most commonly used arc-shaped BSS under the vertical uniformly distributed load and the prestressing force. Then, the failure mode of BSS was proposed based on the static equilibrium. On condition the structural stability was reliable, BSS under the uniformly distributed load would fail by tensile strength failure of the string, and the beam remained in the elastic or semi-plastic range. On this basis, the limit load of BSS was given in virtue of the elastic solutions. In order to verify the linear elastic and limit state solutions proposed in this paper, three BSS modal were tested and the corresponding elastoplastic large deformation analysis was performed by the ANSYS program. The proposed failure mode of BSS was proved to be correct, and the analytical results for the linear elastic and limit state were in good agreement with the experimental and FEM results.

• 콘크리트학회논문집
• /
• 제26권3호
• /
• pp.255-266
• /
• 2014

이 논문은 새로운 수직 접합부와 현장타설 습식 접합부를 가진 T형 프리캐스트 벽체의 내진 성능에 관한 연구이다. 반복하중을 받는 T형 PC 벽체의 하중-변위 관계, 강도, 연성도, 파괴 모드, 그리고 변형 능력에 대해 알아보았다. 실험체 주요 변수는 전단력 전달을 위한 대각 철근의 유무이다. 벽체의 양단에 위치한 길이방향 주철근이 먼저 항복을 하였고 최종 변형은 C형 접합부의 파괴에 의해 결정되었다. 그리고 전단력 전달을 위한 대각 철근은 균열 제어에 효과적인 것으로 나타났다. 단면 해석을 통해 구한 강도와 변형은 실험값과 대체로 일치하였다.

• 한국디지털건축인테리어학회논문집
• /
• 제13권4호
• /
• pp.5-12
• /
• 2013

Conceptual and technical design designated as digital architecture has been discussed with disorderly meaning as a conception only. Thus, this study aims at verification of development possibility for the digital architecture by analyzing how works of Frank Gehry have effect on nonlinearity of the digital architecture. Nonlinear characteristics appeared on works of Frank Gehry analyzed on the basis of expression techniques and modeling principle are as follows: 1) Initial works show a trend to gradually change and develop from horizontal and vertical linear structure to nonlinear pattern. 2) From a nonlinear modeling principle, initial works appear the primary deformation elements only, while afterwards, they are gradually developing to a pattern to mix the primary and secondary deformation elements as introduction of digital architecture. 3) Through specific cases, Frank Gehry has conducted attempts with various method for nonlinear pattern expression. 4) From the initial works to the latest works, continuity becomes higher and changed to nonlinear pattern. This study is significant from a viewpoint that it has verified development possibility of digital architecture by analyzing nonlinear trend of digital architecture for Frank Gehry and it is required to conduct multilateral researches related to the digital architecture.

• 한국정밀공학회지
• /
• 제11권1호
• /
• pp.89-96
• /
• 1994

This study is to develop a new composite material, a mixture of epoxy resin and granite aggergates which is called Expoxy-Granite, to overcome the inherent disadvantages of conventional materials commonly used as a bed structure material of long-term dimensional/ thermal stability. Under the various manufacturing conditions which could be formulated through experimental investigation, we have constructed 6 kinds of Epoxy-Granite structure models having one fifth the size of the ultra-precision machine tool bed structure. They are compared with cast iron and pure granite models through the dynamic test and the thermal deformation test. Both in the steel ball dropping test and in the forced vibration test, three types of epoxy-granite models made in this study have shown much better dynamic characteristics than the cast iron model and almost the same characteristics as compared with the pure granite model. In the thermal deformation test the above composite materials have also represented lower thermal displacements in the vertical direction of each model as compared with other specimens. It is therefore seen that the epoxy-granite complsite material can be applied to the construction of high-precision machine tool bed, instead of cast iron or pure granite.

• 소성∙가공
• /
• 제17권1호
• /
• pp.27-34
• /
• 2008

In order to manufacture a doubly curved sheet metal, the incremental roll forming process which adopts advantages such as the flexibility of the incremental forming process and continuous bending deformation of the roll forming process has been experimentally investigated. An experimental equipment was developed which was named as unit roll set (URS) consisting of two pairs of support rolls and an upper center roll. The upper roll equipped with the servo control unit is motor-driven and can be positioned in the vertical direction according to the user's commands. Four support rolls are idle, and they freely rotate only along the axis so as to transfer the plate more stably in the tangential direction of the rotation of the driving roll. In the process, the plate is deformed incrementally as deformation proceeds simultaneously in longitudinal and transverse directions. Through the experiments using URS, information regarding to forming schedules is found out to fabricate curved hull plates. This study demonstrates the further application of the incremental roll forming process in shipbuilding industries.

• 한국수산과학회지
• /
• 제23권3호
• /
• pp.215-224
• /
• 1990

포화상태인 물질의 역학적, 수리학적 거동을 연구할 수 있는 유한요소법적 수치해석모델을 개발하여 부산 남항 인근해역의 미고결 퇴적물의 거동을 분석하였다. 하중재하에 의한 상부세립 퇴적물의 역학적 변형은 공극수의 확산에 따른 공극수압의 수리학적 변화에 크게 영향을 받는 것으로 나타났다. 하중이 일정지역에 편재되어 있을 경우 포아송효과 및 과잉공극수압의 영향에 의해 하중을 직접 받지 않는 표층부분이 융기되며, 하중경계지역에서 멀어질수록 점근적으로 증가한다. 세립점토층에 비해 높은 투수성을 갖는 하부 모래층은 공극수확산의 통로역할을 하여 과잉공극수압의 소멸을 촉진시키며, 결과적으로 상부점토층 변형의 시간적 변화에도 영향을 끼친다.

• Structural Engineering and Mechanics
• /
• 제60권2호
• /
• pp.251-269
• /
• 2016

In common structural systems, there are some limitations to provide adequate lateral stiffness, high ductility, and architectural openings simultaneously. Consequently, the concept of T-Resisting Frame (TRF) has been introduced to improve the performance of structures. In this study, Configuration of TRF is a Vertical I-shaped Plate Girder (V.P.G) which is placed in the middle of the span and connected to side columns by two Horizontal Plate Girders (H.P.Gs) at each story level. System performance is improved by utilizing rigid connections in link beams (H.P.Gs). Plastic deformation leads to tension field action in H.P.Gs and causes energy dissipation in TRF; therefore, V.P.G. High plastic deformation in web of TRF's members affects the ductility of system. Moreover, in order to prevent shear buckling in web of TRF's members and improve overall performance of the system, appropriate criteria for placement of web stiffeners are presented in this study. In addition, an experimental study is conducted by applying cyclic loading and using finite element models. As a result, hysteresis curves indicate adequate lateral stiffness, stable hysteretic behavior, and high ductility factor of 6.73.

• 한국지반공학회논문집
• /
• 제32권3호
• /
• pp.49-60
• /
• 2016

일반적으로 흙의 파괴는 전단 변형이 집중되는 영역인 전단면의 형성과 발달에 의해 발생한다. 정규압밀 점성토의 파괴거동을 확인하기 위해 시료 내부의 변형거동 분포에 대해 평가가 필요하다. 본 연구에선 재성형된 카올리나이트 시료에 대해 평면변형률 시험을 수행하였으며, 전단 과정에서 일정 변형률 간격에서 디지털 이미지 해석을 수행하였다. 시험 결과로 도출된 응력-변형률 결과를 통해 4개의 단계를 결정하여 시료의 변형거동과 전단면 특성을 평가하였다.

• 한국전산구조공학회논문집
• /
• 제16권1호
• /
• pp.19-32
• /
• 2003

주상복합건물의 구조시스템은 휨변형에 의해 횡력에 저항하는 전단벽 구조와 전단변형에 의해 저항하는 라멘구조의 복합구조로 이루어져 있으며, 이 두 구조의 원활한 힘의 전달을 위하여 전이층에 주로 춤이 큰 보를 사용한다. 주상복합건물은 이러한 큰 질량과 강성을 갖는 전이층으로 인하여 유한요소법에 의한 해석 시 동적 해석을 수행하여야 하며, 일반적인 해석 절차로는 해결하기 어려운 많은 문제점을 야기한다. 일반적으로 주상복한건물의 해석시 전이층 바닥판은 강막을 적용하거나 판요소로 직접 입력하나 적절한 평가없이 사용되고 있다. 따라서 본 연구에서는 강막 적용에 따른 영향을 평가하여 올바른 해석 방법을 제시한다.

• Structural Engineering and Mechanics
• /
• 제17권5호
• /
• pp.641-654
• /
• 2004

This paper presents a theoretic model of a smart structure, a transversely isotropic piezoelectric thick square plate constructed with three laminas, piezoelectric-elastic-piezoelectric layer, by adopting the first order shear deformation plate theory and piezoelectric theory. This model assumes that the transverse displacements through thickness are linear, and the in-plane displacements in the mid-plane of the plate are not taken to be account. By using Fourier's series expansion, an exact Navier typed analytical solution for deflection and electric potential of the simply supported smart plate is obtained. The electric boundary conditions are being grounded along four vertical edges. The external voltage and non-external voltage applied on the surfaces of piezoelectric layers are all considered. The convergence of the present approach is carefully studied. Comparison studies are also made for verifying the accuracy and the applicability of the present method. Then some new results of the electric potentials and displacements are provided. Numerical results show that the electrostatic voltage is approximately linear in the thickness direction, while parabolic in the plate in-plane directions, for both the deflection and the electric voltage. These results are very useful for distributed sensing and finite element verification.