• Structural Engineering and Mechanics
• /
• 제25권6호
• /
• pp.691-716
• /
• 2007

The purpose of the present work is to establish a method for predicting the location and depth of a crack in a circular cross section beam by only considering the frequencies of the cracked beam. An accurate knowledge of the material properties is not required. The crack location and size is identified by finding the point of intersection of pulsation ratio contour lines of lower vertical and horizontal modes. This process is presented and numerically validated in the case of a simply supported beam with various crack locations and sizes. If the beam has structural symmetry, the identification of crack location is performed by adding an off-center placed mass to the simply supported beam. In order to avoid worse diagnostic, it was demonstrated that a robust identification of crack size and location is possible if two tests are undertaken by adding the mass at the left and then right end of the simply supported beam. Finally, the pulsation ratio contour lines method is generalized in order to be extended to the case of rectangular cross section beams or more complex structures.

• Structural Engineering and Mechanics
• /
• 제44권2호
• /
• pp.257-266
• /
• 2012

Walls are the most important vertical load-carrying elements of masonry structures. Their bond designs are different from one country to another. This paper presents the shear effects of some structural bond designs commonly used for masonry walls. Six different bond designs are considered and modeled using finite element procedures under lateral loading to examine the shear behavior of masonry walls. To obtain accurate results, finite element models are assumed in the inelastic region. Crack development patterns for each wall are illustrated on deformed meshes, and the numerical results are compared.

• 헤리티지:역사와 과학
• /
• 제46권2호
• /
• pp.136-149
• /
• 2013

보물 제499호로 지정되어 있는 낙산사 칠층석탑에 대해 표면풍화로 인한 표면균열 발달 양상을 연구하였다. 이 석탑의 석재는 흑운모 화강암과 각섬석-흑운모 화강암으로, 중립질 이상의 입자크기와 회백색을 띄며 특징적으로 거정의 장석 반정을 수반하는 반상조직이 나타난다. 석탑에 나타나는 표면균열은 기단부 및 1층 탑신에서 많이 관찰되며, 대부분 수직, 수평, 대각선 방향으로 발달하고 있다. 석탑에 사용된 석재 내부의 미세균열은 원래부터 리프트 결과 그레인 결의 방향으로 잘 발달한 것이며, 이 두 결이 균열성장과 그에 따른 손상을 야기한 것으로 판단된다. 이와 더불어 석탑에서 나타나는 수직균열은 탑의 자체 하중에 의한 압축응력과 평행하게 미세균열이 성장하였으며, 수평균열은 주 압축응력에 대한 반발 인장력이 균열의 성장을 촉진시킨 것으로 판단된다. 한편, 석탑의 남동쪽 부재 탈락은 압축과 인장에 의한 것과 더불어 거정질 알칼리장석 반정의 벽개와 쌍정면의 영향으로 인해 발생한 것으로 해석된다.

• 대한기계학회논문집A
• /
• 제21권7호
• /
• pp.1097-1105
• /
• 1997

Because of the existence of stress interaction field made by other defects and propagating cracks, the structure may be weakened. Therefore in this study, the crack behavior in the interaction field made by two different cracks is studied experimentally. In the experiment, vertical distance between two cracks and applied stress are varied to make different stress interacted field. In addition, the effect of plastic zone is used to examine crack propagation path and rate. Three types of crack propagation in the interacted field were found, and crack propagating path and rate of two cracks were significantly changed according to different applied stress as each crack propagates. And the results are attributed to the effect of the size and shape of the plastic zone.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계학술발표회 논문집(I)
• /
• pp.210-213
• /
• 2006

The objectives of this study is to find out the relationship of crack width and residual seismic capacity of Unreinforced Masonry(URM) walls which were damaged by earthquake. Three URM walls which made the shape ratio(1/h, 1.0, 1.5, 2.0)to be a variable were tested for the objective. It was seen that the crack width increased with growing at rotation angle. Also, this study found out that failure mode affects crack type of URM. In other words, horizontal and vertical crack was increased in rocking and sliding failure mode respectively.

• Journal of Mechanical Science and Technology
• /
• 제14권10호
• /
• pp.1072-1080
• /
• 2000

Leakage magnetic flux (LMF) is widely used for non-contact detection of cracks. The combination of optics and LMF offers advantages such as real time inspection, elimination of electrical noise, high spatial resolution, etc. This paper describes a new nondestructive evaluation method based on an original magneto-optical inspection system, which uses a magneto-optical sensor, LMF, and an improved magnetization method. The improved magnetization method has the following characteristics: high observation sensitivity, independence of the crack orientation, and precise transcription of the geometry of a complex crack. The use of vertical magnetization enables the visualization of the length and width of a crack. The inspection system provides the images of the crack, and shows a possibility for the computation of its depth.

• 대한기계학회논문집A
• /
• 제25권8호
• /
• pp.1163-1172
• /
• 2001

The two dimensional problem of a layered tribological system(TiN/Steel) containing a vertical surface breaking crack and subject to rolling contact is considered in this study. Using finite elements and stress extrapolation method, a series of preliminary models are developed. Preliminary results indicate that the extrapolation technique is valid to determine Modes I and II stress intensity factors for cracks. In the case of TiN/Steel medium, KI and KII were determined for variations in crack length, layer thickness, and load location. The results show that KII reaches maximum values when the contact is adjacent to the crack where Mode I stresses are compressive. KII values decrease with decreased crack length and significantly decrease for reduced layer thickness.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1997년도 봄 학술발표회 논문집
• /
• pp.235-240
• /
• 1997

The purpose of this experiment is to verify processing crack direction and state by the corrosion of electrifying re-bar in the salt water. The result of this experiment is the fact that the first crack appear on the surface of water-because of supplying of oxygen and water. The crack processing is on a surface to be contacted by air and to bottom as mainly the vertical direction from a surface of water. The crack by corrosion of steel reinforcing is emerged by the inside of concrete rather than surface concrete.

• 한국정밀공학회지
• /
• 제14권6호
• /
• pp.135-141
• /
• 1997

Low velocity impact test and compressive residual strength test after impact were performed by using Hercules AS4/3501-6[45/0/-45/90]$_{2s}$ laminated plate to investigate the low velocity impact damage behavior and the post-impact strength degradation on orthotropic composite laminate plate. Due to the lateral impact losd, the load path showed "" shape according to the laminate central deflection. Damage in a laminate occurs by inclined matrix crack at the damage initiation load stage and vertical matrix crack, occurs on the outer surface. Evaluating the compressive residual strength after the low velocty impact test, it could be found that there is a transient range where the compressive residual strength drop suddenly in the initial damage which is in the matrix crack range and the initial delamination area. is in the matrix crack range and the initial delamination area.

• Geomechanics and Engineering
• /
• 제16권6호
• /
• pp.655-667
• /
• 2018

To evaluate the stability of a rock slope with one pre-exiting vertical crack, this paper performs corresponding probabilistic stability analysis. The existence of cracks is generally ignored in traditional deterministic stability analysis. However, they are widely found in either cohesive soil or rock slopes. The influence of one pre-exiting vertical crack on a rock slope is considered in this study. The safety factor, which is usually adopted to quantity the stability of slopes, is derived through the deterministic computation based on the strength reduction technique. The generalized Hoek-Brown (HB) failure criterion is adopted to characterize the failure of rock masses. Considering high nonlinearity of the limit state function as using nonlinear HB criterion, the multivariate adaptive regression splines (MARS) is used to accurately approximate the implicit limit state function of a rock slope. Then the MARS is integrated with Monte Carlo simulation to implement reliability analysis, and the influences of distribution types, level of uncertainty, and constants on the probability density functions and failure probability are discussed. It is found that distribution types of random variables have little influence on reliability results. The reliability results are affected by a combination of the uncertainty level and the constants. Finally, a reliability-based design figure is provided to evaluate the safety factor of a slope required for a target failure probability.