• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.10
• /
• pp.49-56
• /
• 1992

A new global routing algorithm which dynamically adjusts its cost parameters depending on the given routing poroblem to find a near optimum solution has been developed. The proposed algorithm efficiently performs global routing on general area in which all the pin positions are given. This algorithm is composed of two phases`In the first phase, it routes each net by searching a minimum cost path while ignoring the channel capacity. In the second iterative phase, it rips up nets which pass the channel at which the horizontal or vertical routing density exceeds the capacity and then it reroutes them using a modified set of cost parameters. Applying the above phases, paths for nets are found such that routing density doesn't exceed the capacity in each channel and that nets are routed with minimum cost. Experimental results for several benchmark examples including difficult-4, difficult-8, difficult-16, Primary1 and Primary2 show that our method generates better results than other published ones.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.1
• /
• pp.66-71
• /
• 2008

In this paper, an antenna-switching scheme using negative acknowledgement for hybrid automatic repeat request (H-ARQ) is proposed and analyzed in the Vertical Bell Labs Layered Space-Time(V-BLAST) system, in which the transmit antenna is alternatively switched under retransmission. By analytically evaluating the channel capacity of the proposed scheme over correlated fading channels, it is shown that the adverse effect of the channel correlation is alleviated by the antenna switching scheme. Simulation results demonstrate that the average throughput may be improved in a correlated fading channel without adding much complexity to the process.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.8
• /
• pp.78-88
• /
• 1992

To improve the characteristics of sub$\mu$m short channel MOSFET device, a new device having the convex structure is proposed. This device has 3-dimensionally expandable channel length according to the vertical etched silicon height. For the purpose of comparing the DC and AC characteristics, planar device is also fabricated. Comparing the channel length, the convex device with 0.4$\mu$m silicon height is larger about 0.56$\mu$m in NMOS and 0.78$\mu$m in PMOS than planar devices. DC characteristics, such as threshold voltage, operational current, substrate current and breakdown voltage are compared together with AC characteristics using the ring oscillator inverter delay. Also process and device simulation are performed and the differences between convex and pranaldevice are also compared.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.4
• /
• pp.546-553
• /
• 2001

A Parametric study is numerically carried out for flow fields in a two-dimensional plane channel with thin obstacles(“baffles and blocks”) mounted symmetrically in the vertical direction and periodically in the streamwise direction. The aim of this investigation is to understand how various geometric conditions influence the critical characteristics and pressure drop. A range of BR(the ratio of baffle interval to channel height) between 1 and 5 is considered. Especially when BR is equal to 3, for which the critical Reynolds number turned out to be minimal, we add blocks in the center region in order to study their destabilizing effects on the flows. It is revealed that the critical Reynolds number is further decreased by the presence of the block.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.25 no.6
• /
• pp.421-425
• /
• 2016

Micro-EDM is one of the recent fine-machining technologies. Micro-EDM is widely used in precision processes because products manufactured via EDM are free from workpiece hardness. However, the debris produced during the process cause many problems such as reduced precision of the process. The first solution of this problem involves using the milling hole process. Micro-EDM hole process involves an electrode moving rapidly in the vertical direction via a servo system to disperse debris. However, this process can cause reduced work efficiency owing to contact between the electrode and workpiece. In this study, ultrasonic vibration is added to micro-EDM channel machining. Ultrasonic vibration removes the debris during machining and enables precision machining. Consequently, a clean work environment for the subsequent processes is maintained.

• Proceedings of the IEEK Conference
• /
• summer
• /
• pp.110-113
• /
• 2004

Underwater acoustic(UWA) communication is one of the most difficult field because of several factors such as multipath propagation, high temporal and spatial variability of channel conditions. Therefore, it is important to model and analyze the characteristics of underwater acoustic channel such as multipath propagation, transmission loss, reverberation, and ambient noise. In this paper, UWA communication channel is modeled with a ray tracing method and applied to image transmission. Quadrature phase shift keying(QPSK) and multichannel decision feedback equalizer(DFE) are utilized as phase-coherent modulation method and equalization technique, respectively. The objective is to improve the performance of vertical sensor array than that of single sensor in the viewpoint of bit error rate(BER), constellation output, and received image quality.

• ETRI Journal
• /
• v.37 no.5
• /
• pp.906-916
• /
• 2015

High-speed I/O channels require adaptive techniques to optimize the settings for filter tap weights at decision feedback equalization (DFE) read channels to compensate for channel inter-symbol interference (ISI) and crosstalk from multiple adjacent channels. Both ISI and crosstalk tend to vary with channel length, process, and temperature variations. Individually optimizing parameters such as those just mentioned leads to suboptimal solutions. We propose a joint optimization technique for crosstalk cancellation (XTC) at DFE to compensate for both ISI and XTC in high-speed I/O channels. The technique is used to compensate for between 15.7 dB and 19.7 dB of channel loss combined with a variety of crosstalk strengths from $60mV_{p-p}$ to $180mV_{p-p}$ adaptively, where the transmit non-return-to-zero signal amplitude is a constant $500mV_{p-p}$.

• Journal of Advanced Marine Engineering and Technology
• /
• v.29 no.1
• /
• pp.49-59
• /
• 2005

The evaporation heat transfer experiments are conducted with the shell and plate heat exchanger (S&PHE) without oil in the refrigerant loop using R-410A. An experimental refrigerant loop has been established to measure the evaporation heat transfer coefficient h. of R-410A in a vertical S&PHE. Two vertical counter flow channels were formed in the S&PHE by three plates haying a corrugated trapezoid shape of a $45^{\circ}C$ chevron angle. UP flow of the boiling R-410A in one channel receives heat from the hot down flow of water in the other channel The effects of the refrigerant mass flux. average heat flux. refrigerant saturation temperature and vapor qualify are explored in detail. Similar to the case of a plate heat exchanger. even at a very low Reynolds number, the flow in the S&PHE remains turbulent. The Present data shows that the evaporation heat transfer coefficients of R-410A increased with the vapor qualify. The results indicate a rise in the refrigerant mass flux caused an increase in the h.. Raising the imposed wall heat flux is found to slightly improve h., while h, is found to be lower at a higher refrigerant saturation temperature. Based on the present data. empirical correlation of the evaporation heat transfer coefficient is proposed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.27 no.1
• /
• pp.108-116
• /
• 2003

In this paper, the experimental results of condensation heat transfer were reported for the plate and shell heat exchangers(P&SHE) using R-l34a. An experimental refrigerant loop has been established to measure the condensation heat transfer coefficient of R-l34a in a vertical P&SHE. Two vertical counter flow channels were formed in the P&SHE by three plates of geometry with a corrugated trapezoid shape of a chevron angle of 45$^{\circ}$. Downflow of the condensing R-l34a in one channel releases heat to the cold up flow of water in the other channel. The effect of the refrigerant mass flux, average heat flux, system pressure and vapor quality of R-l34a on the measured data were explored in detail. The results indicate that at a higher vapor quality the condensation heat transfer coefficients are significantly higher. Condensation heat transfer coefficients were increased when the refrigerant mass flux was increased. A rise in the average heat flux causes an slight increase in the hr. Finally, at a higher system pressure the hr is found to be lower. Correlation is also provided for the measured heat transfer coefficients in terms of the Nusselt number.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.6
• /
• pp.51-56
• /
• 2005

This paper introduces an altitude determination algorithm using GPS/INS/Baroaltimeter and evaluates the algorithm by real field tests. The test results show that the proposed method can determine the altitude of an aircraft continuously and sensitively. Therefore, it is appropriate to be used as an altimeter for a flight control system, especially for the automatic take-off and landing. In addition, it is shown that the second and the third baro-inertial vertical channel damping methods are essentially complementary filters while the proposed scheme improves these complementary filters.