• 자동차안전학회지
• /
• 제14권4호
• /
• pp.106-112
• /
• 2022

The purpose of this study is to explore ways of improving the motor vehicles safety certification system in preparation for the deployment of Lv.4 or higher autonomous vehicles. In order to effectively achieve the objectives of this study, theoretical and empirical research methodologies were employed, including literature review of prior research, government-published data, etc.; comparative research on legislative cases of other countries regarding motor vehicles safety certification; historical and legal research on domestic systems; legal analysis to explore approaches for improvement, etc. Some argue that the type approval system is needed in preparation for deploying autonomous vehicles, but there are several limitations in moving to the type approval system from the self-certification system currently adopted in Korea. First, there is a possibility that the system may be in conflict with the Korea-U.S. MOU regarding Foreign Motor Vehicles (1988) and the Korea-U.S. FTA (2011); second, there is a risk of undermining the cause of the self-certification system, which is the autonomy of manufacturers; third, the boundary between autonomous vehicles and non-autonomous vehicles is unclear; and fourth, the type approval system may hinder technological competitiveness. On the other hand, considering that the Korea-U.S. FTA and the UNECE IWVTA recognize exceptions to deal with road safety and risks to human health or the environment, and have a pre-certification system for some auto parts such as pressure-resistant containers, it can be said that there is room to introduce the type approval system for supplementation purposes. To improve the motor vehicles safety certification system while ensuring the safety of autonomous vehicles of Lv.4 or higher, the targets of type approval should be defined and the criteria, procedures, etc. for type approval should be established. At the same time, the consistency between motor vehicle-related laws and harmonization with international standards need to be considered.

• 동력기계공학회지
• /
• 제20권5호
• /
• pp.60-65
• /
• 2016

Dynamic performance of transmission has a substantial effect on dynamic performance and fuel efficiency of a vehicles. Dynamic performance of transmission and mass moments of inertia of transmission gears are related directly each other. Then a smaller amount of kinetic energy from vehicles that repeat acceleration and deceleration requires lighter rotating part in transmission. It is going to increases fuel efficiency as a result. In this study, equivalent inertia moments of inertia at different speeds were calculated by simplifying the transmission system. To find out lightening effect at low speed level gear on fuel efficiency, the powerflow of transmission was analyzed. And the lightning effect of the rotating parts in transmission is compared with the mass reduction of sprung parts in vehicle.

• 산업경영시스템학회지
• /
• 제19권40호
• /
• pp.107-117
• /
• 1996

This paper considers the part assignment to workstations in flexible manufactuirng system (FMS). Parts are processed through several workstations according to processing order. The machines of each workstation can do multiple Processing functions. Therefore, a processing of a part can be processed in several workstations, which are non-identical in functional performance. Although a processing of a part can be processed in the multiple workstations, it has to be processed in only one among available several workstations, Parts are transported with unit load by automated guided vehicles (AGVs). The criteria of part assignment is to minimize the maximum value of the processing times of each workstation and the total transport times of vehicles. Model formulation is suggested, and numerical example is shown.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2003년도 추계학술대회 논문집
• /
• pp.12-17
• /
• 2003

The basic concept of an improved business and productivity for Small and Medium Sized Enterprizes, which makes use of an information portal, is to assure competitive power, increase the production quantity through the interchange of a company and the outside environment, and to build cooperation. To reduce the charge of the equipment, as well as to introduce and information program, it should build an information environment from inside the company by suing the information portal ASP(Application Service Provider). This portal is already built by the basic information infrastructure through the Internet.

• 한국자동차공학회논문집
• /
• 제20권6호
• /
• pp.92-99
• /
• 2012

It is often thought that because no-start motor vehicles cannot start an engine, a fire cannot occur for motor vehicle causes. However, although the engine cannot start up, some parts may be live with electricity if a battery is connected. If the parts have problems, a fire can occur. This study analyzed the causes of fires occurring when a motor vehicle was loaded onto a tow truck to service no-start. It is suggested that no-start motor vehicles should separate a battery terminal to prevent a fire. And this fire is related to automotive products liability.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.1231-1236
• /
• 2007

Balance Shaft Module is module parts that is installed to vehicles engine to reduce noise and vibration of vehicles engine. Balance Shaft Module's performance exerts important influence on performance of engine. Therefore, must be able to warrant quality and performance of Balance Shaft Module. Existing product found and revised error at continuous process of production, and estimated failure mode in Balance Shaft Module. Previous method hard to secure product that performance is excellent, and bring a lot of damages economically. Therefore, development of inspectin system for quality inspection of parts and performance test of assembly is essential in Balance Shaft Module. In this study, represented development process of automatic dynamic inspection system to test performance and detect breakdown of Balance Shaft Module that is producing in Dongbo.

• 한국자동차공학회논문집
• /
• 제15권2호
• /
• pp.182-186
• /
• 2007

This paper studied performance characteristics of hybrid automotive to replace existing fossil fuel vehicles. Specially, about power split type HEV that is T-HEV's drive system when a vehicle drives at steady speed, monitored both output of each engine, motor and generator and battery SOC (state of charge) and analyzed performance characteristic of power transmission system and electricity power parts. This study shows those that acquired and analyzed information from signals between HCU and each controller of actual T- vehicle. From this study, it is confirmed that each conditions of EV and HEV drive can be a improvement with respect to the fuel efficiency of vehicles.

• 자동차안전학회지
• /
• 제14권3호
• /
• pp.77-82
• /
• 2022

The Korea's automobile safety standards consist of standards for automobiles, automated vehicles, two-wheeled vehicles and auto parts, and there are 157 articles. In connection with the safety standards, the implementation rules stipulated for detailed test methods and procedures are composed of the main body, asterisks and annexes, and have a rather complicated structure. In addition, the test items in the asterisk are specified with the same or similar name as the test items in other asterisks. In this study, the structure of these implementation rules is simplified and the same test items are integrated. This is expected to increase the user's understanding of laws and regulations and efficiency.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.947_948
• /
• 2009

In an attempt to minimize the air pollution caused by CO2, $NO_X$x, and $SO_X$ and the fuel cost, the auto industries and researchers recently are looking into replacing the diesel and gasoline cars with hybrid electric vehicles, plug-in electric vehicles, or battery powered electrical vehicles. This paper reports the technical status of the primary components such as batteries, motors, power control units and auxiliary parts to be used for electric vehicles.

• 제어로봇시스템학회논문지
• /
• 제3권1호
• /
• pp.40-45
• /
• 1997

A robust disturbance rejection controller for the hovering motion of underwater vehicles in near the surface of sea is presented. The suggested controller consists of two control parts, the one is disturbance observer for taking into account the effects of sea wave and missile-launching forces, and the other is sliding mode controller for the robust stability of underwater vehicles with model uncertainties and nonlinearities. It is shown that the sliding mode control system with disturbance observer is more effective compared with the sliding mode control system, especially in case that large sea wave force is affected.