• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2006년도 추계학술대회 논문집(제1권)
• /
• pp.317-323
• /
• 2006

본 시험의 목적은 컨테이너터미널의 생산성을 향상시키기 위해서 기술개발 추진 중인 컨테이너 자기하역차량(ALV:Automated Lifting Vehicle)의 핵심 기술개발 요소 중 하나인 주행구동장치 (Gantry Travel Mechanism) 시제품을 제작하여, 무부하 및 부하 조건에서 각종 Test와 한계하중 실험 과정을 통하여 설게 Data의 확인과 상세 제작도면의 오류를 사전에 발견하여 최종 제작도면에 수정 반영함으로써 보다 완벽한 장비를 개발하는 것을 목적으로 한다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1998년도 춘계학술대회논문집; 용평리조트 타워콘도, 21-22 May 1998
• /
• pp.102-107
• /
• 1998

UTM-01 is the first fall sized maglev test vehicle which is being developed by KIMM and Hyundai Precision and Industrial Co., since 1995. The vehicle employs normal conducting magnets for levitation and single sided linear induction motor for propulsion. The test vehicle has been under tests to assure its required performance since last May 1997. This paper reports various system level test results compared with simple 2 degree of freedom dynamic calculations. Test results include performance of the levitation and guidance system, propulsions system, and the dynamic behavior of the elevated guideway under the passage of the maglev vehicle.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 춘계학술대회논문집
• /
• pp.357-361
• /
• 2003

According to the remarkable reduction of the vehicle noise, the important of tire noise which is generated from the vehicle and the necessities of the researches for the noise reduction are emphasized. In this study, we have studied the road noise which is excited by the interaction between tire and road. In order to evaluate the road noise, we carry out the subjective test(feeling test). In order to consider the effect of the vehicle suspension for the tire/road noise, we are equipped with identical tires on the differential vehicle suspension and evaluate the road noise. In order to consider the effect of the tire structure for the tire/road noise, we evaluate the some tires with various structures. From the test results, we fine that the difference of road noise is generated by the variation of the vehicle suspension. Also, we can select the optimized tire structure which can be reduced the road noise.

• 한국자동차공학회논문집
• /
• 제4권5호
• /
• pp.90-99
• /
• 1996

To keep up with the regulation of OBD II(on board diagnostics II), many detection methods for engine misfire have been developed. Among them, the method of using the crankshaft speed fluctuation is the most noticeable in the point of view of lower cost and easier installation than any others. On the basis of the results obtained from the previous engine-dynamometer test, the integrating torque index (ITI) has been introduced. In this research, the instrumental and the interfacing systems to engine control unit(ECU) are developed for the vehicle test. Therefore, the vehicle and chassis-dynamometer test can be carried out in addition to the rough road test. From this test, the previousproposed method proved that it can be applied to the real vehicle.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.924-930
• /
• 2011

Maglev vehicle has two parts a vehicle body and a series of bogies. The vehicle body is connected through a pneumatic suspension on the bogie frame operating loads, vehicle weight and passengers, repeatedly during the service life. The bogie frame plays an important role in sustaining the weight of the vehicle body and controlling the magnets in the correct alignment to meet requirements of stable running on railway. It is also subjected to the levitation and guidance force and propulsion force generated by electromagnets and linear induction motor (LIM) respectively. To guarantee a vehicle system, it is necessary to identify a load test method with proper loads that the vehicle is expected to experience while in service. In this paper, a test method was proposed to verify the structural safety of vehicle body and bogie frame that are applied to an EMS(electromagnetic suspension)-type urban Maglev vehicle considering in case of not only running on the ground but also levitated running.

• 한국자동차공학회논문집
• /
• 제16권1호
• /
• pp.114-120
• /
• 2008

Recently, the nano-PM's number concentration emitted by diesel internal combustion engine has focused on attention because this particulate matters are suspected being hazardous of human health. In this study, The nano-PM mass and size of diesel passenger vehicles were measured on chassis dynamometer test bench. The particulate matters(PM) emissions of these vehicles were investigated by number concentration too. A condensation particle counter(CPC) system was applied to measure the particle number and size concentration of diesel exhaust particles at the end of dilution tunnel along the NEDC(ECE15+EUDC) and CVS-75 vehicle test mode. As the research result, the characteristic of vehicle test mode on the diesel nano-particle number and size distribution was investigated in this study.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.980-985
• /
• 2008

This paper presents vehicle road test of a semi-active suspension system equipped with continuously controllable magnetorheological (MR) dampers. As a first step, front and rear MR dampers are designed and manufactured based on the optimized damping force levels and mechanical dimensions required for a commercial middle-sized passenger vehicle. After experimentally evaluating dynamic characteristics of the MR dampers, the test vehicle is prepared for road test by integrating current suppliers, real-time data acquisition system and numerous sensors such as accelerometer and gyroscope. Subsequently, the manufactured four MR dampers (two for front parts and two for rear parts) are incorporated with the test vehicle and a skyhook control algorithm is formulated and realized in the data acquisition system. In order to emphasize practical aspect of the proposed MR suspension system, road tests are undertaken on proving grounds: bump and paved roads. The control responses are evaluated in both time and frequency domains by activating the MR dampers.

• 한국소음진동공학회논문집
• /
• 제19권3호
• /
• pp.235-242
• /
• 2009

This paper presents vehicle road test of a semi-active suspension system equipped with continuously controllable magnetorheological(MR) dampers. As a first step, front and rear MR dampers are designed and manufactured based on the optimized damping force levels and mechanical dimensions required for a commercial middle-sized passenger vehicle. After experimentally evaluating dynamic characteristics of the MR dampers, the test vehicle is prepared for road test by integrating current suppliers, real-time data acquisition system and numerous sensors such as accelerometer and gyroscope. Subsequently, the manufactured four MR dampers(two for front parts and two for rear parts) are incorporated with the test vehicle and a skyhook control algorithm is formulated and realized in the data acquisition system. In order to emphasize practical aspect of the proposed MR suspension system, road tests are undertaken on proving grounds: bump and paved roads. The control responses are evaluated in both time and frequency domains by activating the MR dampers.

• 한국철도학회논문집
• /
• 제19권5호
• /
• pp.565-575
• /
• 2016

철도차량 영업 운행 중 빈번히 발생하는 차륜 마모, 손상 등의 결함을 제거하기 위하여 실시되는 차륜 전삭 공정과 관련하여 전삭 전후의 차량 동적성능을 분석하였다. 전동차를 대상으로 차륜 전삭 전후의 차륜답면형상을 계측, 분석하였으며 진동 및 승차감 특성을 분석하고자 차량 주행시험을 실시하였다. 시험결과, 차륜 전삭 후 차량 진동 RMS값은 전삭 전에 비하여 저감되었으며 철도차량 기술기준에 의거 분석한 차체 진동성능은 전삭 전에 비하여 개선되었다. 승차감레벨은 전삭 전에 비하여 전삭 후 좌우, 상하방향 모두 최대 약 3dB의 개선 효과를 보였으며 주행안전성 또한 개선됨을 확인하였다.

• 한국인쇄학회지
• /
• 제23권2호
• /
• pp.1-14
• /
• 2005

Generally, printing inks are composed of pigment, vehicle and additive. Among others, the vehicle transfers the pigment to substrate and then binds it on the surface. So, rheological properties of the vehicle are an important factor which has influence on printability. Thus, in this study, rheology of the vehicle was investigated by using rotational rheometer according to molecular weight of resin. Also, emlusion rheology of water in oil type and its microstructure were examined with increasing the shear rate. Consequently, the following results were obtained: (1) By viscometric flow test, zero shear viscosity and shear thinning index of vehicle increased with increasing the molecular weight of resin. (2) By relaxation and creep test, relaxation time and retardation time of vehicle increased with increasing the molecular weight of resin. (3) By frequency sweep test, crossover point of vehicle increased with increasing the molecular weight of resin. (4) G' and G" of emlusions increased with increasing the molecular weight by amplitude sweep test. (5) The shape of water drop in emlusions was changed to the capillary tube.