• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.873_874
• /
• 2009

This paper presents a method for designing a high power motor that is applicable to electric vehicles. Interior Permanent Magnet (IPM) type motor which has high efficiency and high durability is selected. To apply for the electric vehicles, a form, a tire and a wheel of vehicles are considered when calculating a motor performance. After calculating a motor performance, space harmonic analysis and FEA(Finite Element Analysis) is used for designing In-Wheel motor.

• Proceedings of the KIEE Conference
• /
• 2007.04c
• /
• pp.119-121
• /
• 2007

The increment of electric power demand causes interest on new higher power system such as 42V Power Net, and furthermore necessity for development of energy storage device is highlighted recently. Owing to high efficiency and easy speed control of brushless DC(BLDC) motor, the demand of BLDC motor that has high power and low noises are increasing. Especially demand of interior permanent magnet(IPM) type BLDC with high efficiency and high power in electric motion vehicle is increasing. This paper presents the design of the BLBC motor for EHPS(Electro-Hydraulic Power Steering) in 42V system and verified the characteristics by simulation and test results.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.891-896
• /
• 2007

Noise radiated from the powertrain is an important factor of the vehicle interior noise. In this paper, Finite Element(FE) model and Boundary Element(BE) models were created. The FE model was updated by doing a correlation between experimental modal analysis(EMA) values and finite element analysis(FEA) values. Main bearing forces were calculated using a running modal data. The forced vibration analysis was simulated using the software MSC/NASTRAN, and the radiated noise was predicted using the software LMS/VIRTUAL.LAB.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.1 no.1
• /
• pp.110-119
• /
• 1993

본 논문은 자동변속기를 탑재한 차량에서 에어콘(air condition)을 작동시키고, 공 회전시 기어의 변속을 "D"단에 두었을 때 실내에서 발생하는 이상음의 원인규명 및 해결 방 법에 관한 연구 결과를 논하고자 한다. 이 이상한 소음의 원인을 규명하기 위하여 실린더 내부의 연소압력, 메인 베어링캡(main bearing cap)의 진동, 엔진 마운팅 보스의 진동 및 차 량의 실내소음을 동시에 측정하여 분석하였으며 이 결과에 의하면 이상음의 원인은 크랭크 샤프트(crank shaft)의 굽힘진동이 파워플랜트(power plant)를 가진하여 진동을 증가시키고, 이 진동이 마운팅 보스를 통하여 차량의 차체에 전달되며, 차체의 진동에 의해서 발생하는 고체 전달음(structure-borne noise)이었다. 또한 이상음의 주기는 주파수 성분은 200-400Hz 이었다. 이 이상음은 크랭크 샤프트의 댐퍼 풀리의 질량을 저감하여 크랭크 샤프트의 동특 성을 개선함으로서 해결가능하고, 혹은 점화시기를 지연하여 연소 압력을 낮춤으로서 해결 가능하다.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.4
• /
• pp.555-566
• /
• 2012

This paper presents a thermal analysis of an interior PM synchronous machine with concentrated winding for electric vehicle. The conventional thermal equivalent network model has been used for a long time for calculation of the temperature rises in electrical machines. In spite of being popular, this method can not be applied correctly for elements with complicated cooling structure like liquid cooled housing. To overcome this drawbacks, in this paper, a hybrid thermal model using the result of CFD analysis partly. Using this method, to improve a thermal performance of PMSM with concentrated winding, the effects of two design parameters are analysed. Finally, the accuracy of this model has been verified by experiments for the developed 21kW motor.

• Journal of the korean Society of Automotive Engineers
• /
• v.5 no.2
• /
• pp.15-20
• /
• 1983

The nature and the sources of sound in cars is discussed in the light of many previous works, and the importance of the system resonances inside cars is suggested. An investigation of a 'boom' problem in a small size passenger car is described. It was established that the 'boom' frequencies coincided with engine firing frequency and also with several system resonances. To find out main transmission path of the noise to the car interior, various possible sources were eliminated from the investigation by means of simple modification to the vehicle. Data on the structural modes of the body, and the acoustic modes of the passenger compartment at various forcing cases were obtained to provide better understanding of the problem. It was found that the acoustic resonance responsible for the boom was controlled largely the bending motion of the floor. To investigate the effect of the structural modification to the acoustic response, center floor of the car was reinforced. a great reduction of the noise inside the car especially at the offending speed range, was achieved by this modification.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.880-883
• /
• 1996

This paper suggests a speed control algorithm for the ICC(Intelligent Cruise Controller) system. The speed controller is designed using the fuzzy controller which shows the good performance in nonlinear system having the complex mathematical model. The fuzzy controller was equipped with the capability of a self-learning in real time in order to maintain the good performance of the speed controller in a time-varying environment the self-learning properties and the performance of the fuzzy controller are showed via computer simulation. The suggested fuzzy controller will be applied to the PRV-III which is our test vehicle.

• The Journal of the Acoustical Society of Korea
• /
• v.19 no.2E
• /
• pp.3-7
• /
• 2000

Vibration generated by the non-uniform road profile propagates though each tire and the suspension and finally generates structure born noise in the interior of the passenger vehicle. In this paper, the road-booming-noise which has strong correlation with the vibration signals measured at the suspension system was compensated. Active noise control of the road-booming-noise is rather difficult to achieve because of its non-stationary characteristics. CMFX LMS (Constraint Multiple Filtered-X Least Mean Square) algorithm, which can track non-stationary process rather well, is applied. Comprison of the proposed method and the conventional MFX LMS (Multiple Filtered-X Least Mean Square) algorithm is made through the hardware-in-the-loop simulation and the feasibility of the proposed method is demonstrated with the experiment.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.1768-1773
• /
• 2010

CEN/TS 45545 is Europe consolidation standard for fire safety on railway behicles. This is based on the International Union of Railways(UIC) and different European countries. It is intended to protect passengers and staff in railway in the event of a fire on board. It will be prepared in 2012. Based on this consolidate standard, they are going to make single market, for raising technical competitiveness, technical innovation and globalization of that standard. For this reason, European academies, manufacturers, and sub-manufacturers confer and stady animated about CEN/TS 45545. In Korea, get out the safety assessment for ues incombustible interior material, the needs of quantitative analysis on fire protection, demand on recognition of fire protection scenario, and define about fire load analysis are becomin more and more important. Therefore, this paper will estimate and compare Flammability, Smoke Density, Toxicity Index( this is the key point for appraised fire safety performance of material) between CEN/TS45545 and fire standards on railway vehicle. Then suggest criteria for fire safety on railway vehicles.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.1036-1041
• /
• 2007

In this paper, we studied the optimized design of roof structure to be separable roof structure. Also, the design have to satisfy with the GM/RT 2100' missile protection tests to verify the safety of railway vehicle structure. The separable roof structure design could have easier assembly process than whole roof structure in case of the interior outfitting and so on. Optimized design have to have as good as whole roof structure about results from the structure analysis. We studied separable roof structure to be optimized along with GM/RT 2100. The separable roof structure showed that the results have the same level of structure analysis