• 한국정밀공학회지
• /
• 제7권3호
• /
• pp.37-47
• /
• 1990

In accordance with the high precision of mechanical elements, it has been required to high precision in surface roughness measurement and, therefore, stylus tip radius is manufa- ctured less than 2 .mu. m through ion sputter machining. In this experiment, by suing ion sputter machined stylus pf fine tip, radius and lapping machined stylus, surface roughness of standard specimens, silicon wafer were measured and then Rmax, Ra, RMS value were investi- gatedaccording to the variation of tip radius of stylus. As a result, measuring error due to the variation of stylus tip radius in surface roughness measurement was decreased by using ion sputter machined stylus and also the measuring accuracy was improved. And the measuring variation of Ra, RMS calculated from correlation coefficient lager than 0.9 on the wave of short period and amplitude using ion sputter machined stylus of fine tip radius.

• 한국정밀공학회지
• /
• 제8권3호
• /
• pp.105-113
• /
• 1991

The practicability of Ion-Sputter machining renders it possible to make diamond stylus for surface roughness measurement with micro stylus tip radius less than 2${\mu}mR$, and to measure surface roughness of fine-machined surface. In this study, we researched the wear or Ion-Sputtered stylus with 0.1${\mu}mR$ and 0.5${\mu}mR$ for micro-figure measurement and polished stylus with 0.5${\mu}mR$ according to measurement distance. As a result, we know that the case of Ion-Sputtered stylus is worn down easilier the case of polished stylus. And we know that in the evaluation of stylus wear, it is more useful method that examine the wear by measuring the variation of stylus tip radius than by evaluating the variation of Ra values.

• 대한기계학회논문집
• /
• 제14권6호
• /
• pp.1495-1508
• /
• 1990

본 연구에서는 전류밀도와 가공시간을 변화시켰을 때의 가공량, 가공상태를 검토해 보았으며, 촉침홀더의 가공각도를 달리하거나 재부착문제를 해결하기 위한 마 스크의 사용여부에 따른 촉침의 가공상태를 알아보기 위해 초기선단반경 2$\mu\textrm{m}$, 선단각 90˚의 다이아몬드 촉침을 이온스파터 가공기를 사용하고, 가공조건을 변화시켜서 초 정밀 가공품의 표면거칠기 측정에 적합한 0.5$\mu\textrm{m}$ 이하의 미세한 선단반경을 갖는 촉침 을 가공하기 위한 가공조건에 대한 실험을 하였다.

• 한국주조공학회지
• /
• 제31권4호
• /
• pp.191-197
• /
• 2011

Transparent organic materials have been frequently used as an analog of the solidifying metallic materials, because their transparency permits an in-situ observation of the microstructural development during solidification through optical microscopy. Pivalic acid (PVA)-ethanol system showing an anisotropic property in solid-liquid interfacial energy and interface kinetics was adopted in the present experiment, and the detailed experiments performed are as follows: (1) variation of dendrite tip temperature with growth velocity, (2) correlation between primary dendrite arm spacing (${\lambda}_1$) and the growth orientation away from the heat flow direction (tilt angle: ${\theta}$), (3) variation of dendrite tip radius (R) with growth velocity (V), (4) dendrite tip stability parameter (${\sigma}^*$) and its dependence on the concentration. Concerning the correlation between the dendrite tip temperature and growth velocity the present result is well suited to Hunt-Lu equation. As the tilt angle increases, the average primary dendrite spacing tends to increase.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.31-35
• /
• 2004

The speed competition of optical disk drive has been accelerated with the fast advancement of its storage density and data transmission technology. The continuous increase of the spinning speed of CD meets the unexpected and catastrophic failure of disk during the operation. The effect of its thickness and outer radius of disk were investigated to reduce stresses and J-integral around the crack tip. The effect of its thickness was considered ahead of the crack tip. In the effect of outer radius of disk, linear elastic fracture mechanics was used to obtain the critical crack length, which indicates the onset length for unstable crack growth. This approach is so significant as to detect the growing crack by disk drive before the catastrophic failure, which will provide the standard size of its safety for high-speed disk drive.

• 한국분무공학회지
• /
• 제9권2호
• /
• pp.41-49
• /
• 2004

Liquid breakup under the variation of AC frequency has been studied experimentally in the electrohydrodynamic atomization. The effect of parameters such as charging voltage, flow rate, nozzle tip inner diameter and power frequency have been considered. This work was performed to investigate the experimental analysis for the effect of AC frequency on breakup process, the mapping of occurrence of disintegration region, and the relationship between the applied power and the droplet radius. The experimental results show that the increase of applied voltage in a certain frequency band leads to a reduction in the droplet size within the limits from 50Hz to 400Hz. The transition phenomena from dripping mode to spindle mode were observed under the band of sudden fall of droplet radius changing ratio, and the synchronous region were produced within the range of applied voltage from 5kV to 6kV.

• 태양에너지
• /
• 제6권2호
• /
• pp.86-92
• /
• 1986

This paper presents the aerodynamic performances of horizontal axis wind turbines with non-twisted but taperd blades. Five configurations of blades, namely, one straight blade and four tapered blades with taper ratio of ranging from 0.1 to 0.7 have been simulated. The aerodynamic performances of the wind turbines have been determined over blade incidence angle of ranging from $2^{\circ}$ to $6^{\circ}$ and keeping same solidity and radius of them. The results are presented comparing straight blade from four tapered blades for maximum power coefficient and tip looses against variation of taper ratio. It also shows that the wind turbine with taper ratio of 0.5 has the highest maximum power coefficient than others. And wind turbines with taper ratio below 0.2 have lower values of maximum power coefficients than straight one. The tip loss of straight blade is the largest and reduces Slightly with the decrementation of taper ratio.

• 대한기계학회논문집A
• /
• 제39권10호
• /
• pp.1053-1061
• /
• 2015

본 연구는 테어링 튜브에 플랫 다이를 설치하고 동하중이 가해졌을 때 에너지흡수용량 및 거동을 예측하기 위하여 수행하였다. 컬 끝과 튜브 본체가 접촉할 때 컬 끝의 굽힘이 발생함을 발견하고 식을 제안하였다. 그러나 컬 끝의 굽힘 하중과 에너지 소산율의 예측을 더욱 정확히 하기 위해 컬의 곡률반경의 변화와 튜브 두께의 감소에 주목할 필요가 있었다. X.Huang 등이 제안한 테어링 튜브 이론 모델에 컬의 평균 곡률반경, 감소하는 튜브 두께를 반영한 컬 끝의 굽힘 식을 추가하였고 충돌시험 결과를 통하여 검증하였다.

• 한국분무공학회지
• /
• 제11권3호
• /
• pp.131-139
• /
• 2006

An experimental study was performed to investigate the liquid breakup and atomization characteristics in electrohydrodynamic atomization according to the changing of experimental parameters such as nozzle size, fluid flow, and electrical intensity. An original electrohydrodynamic atomizer equipment was designed and manufactured for the analysis of spray visualization and the exploration of relationship between applied power and the behavior of liquid atomization. The image processing technique by using the back-illumination method was applied to visualize the distilled liquid breakup process and to examine the variation of the droplet size distribution. The results show that the spray modes of electrohydrodynamic atomization are closelyconnected by the strength of the electric stresses at the surface of the liquid film and the kinetic energy of the liquid jet leaving the needle tip.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 1999년도 유체기계 연구개발 발표회 논문집
• /
• pp.252-256
• /
• 1999

In this research, the performance predictions of the submersible mixer were investigated. The variation of the performance characteristics by changing the impeller design parameters were discussed through the flow calculation results by using a commercial program, FLUENT. The performance of the submersible mixers is related to the velocity diffusion profiles downstream of the impeller and also the required input motor power to mix the fluid. In this study, the various design parameters such as the number of blade, the hub and tip diameters, the impeller blade profiles and revolution speed of the blades were taken for the fixed values. The blade sweep direction, the chord length distribution along with the radius of the blade and the inlet blade angle were changed to make different testing models. The flow calculation results show the effect of the changed design parameters on the performance of the submersible mixers and also give some helpful information for designing more efficient submersible mixers.