• Journal of the Korea Society of Computer and Information
• /
• v.8 no.3
• /
• pp.163-169
• /
• 2003

This study was carried out develope a motor power change speed device of motor by used micro- controller. This system was producted a auto-change speed device which switching frequency was 1,000MHz by used a auto- controller. It had a continuous output current such as 5A, 11A, 25A, 35A, 50A. It used a variable voltage from 9V to 18V(Maximum). We designed hardware of and software of micro-controller, we are made up of a auto cut-off function by 3.7V for detected power-loss prevention.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1118-1119
• /
• 2007

Switched Reluctance Motor has advantages such as simple structure, low cost and so on compared with induction motor. Efficiency is higher than induction motor, so there is beneficial cost. Also torque character has essential character of superiority step motor and a DC motor character that depends on variable speed. This paper presented the research of speed and current control system of SRM using the DSP. At first, a simulation model on Matlab/simulink was performed. SRM speed control algorithm investigated the control method. Then driver and control system developed to do experiment.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10a
• /
• pp.1188-1193
• /
• 1993

For the HST(Hydrostatic Transmission) consisted of a variable displacement axial piston pump and motor, a speed controller with efficiencies considered is proposed. To consider a efficiency in speed control, the displacements of pump and motor which maximize a steady state efficiencies with a various load torque are calculated through computer simulation and these results are reflected to speed controller which has PI control structure with cross over control scheme. It is shown through computer simulation that the proposed controller gives better steady state efficiencies compared with the conventional controller and good transient responses.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.215-218
• /
• 2000

The windup phenomenon appears and degrades control performance when a controller with integrating action is used and the plant input is limited. An anti-windup integral -proportional(IP) controller is proposed for the variable-speed motor drives and it is experimentally applied to the speed control of a vector-controlled induction motor driven by a pulse width modulated (PWM) voltage source inverter(VSI). Although the operating conditions like motor load and speed command is changed under the limited plant input it is experimentally verified that the speed response has much improved performance such as no overshoot and fast settling time and the maximum plant input is also effectively utilized.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.40 no.1
• /
• pp.45-54
• /
• 2003

Turbo compressor needs high speed rotation of impeller in structure, high rated gearbox and conventional induction motor. This mechanical system increased the moment of inertia and mechanical friction loss. Resently, the study of turbo compressor applied super high speed motor and drive, removing gearbox made its sire small and mechanical friction loss minimum. This paper describes the implementation of the vector control schemes for a variable-speed 131㎾ PMSM(Permanent Magnet Synchronous Motor) drive in super-high speed application.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.890-891
• /
• 2015

본 논문에서는 속도 제어를 위한 가변자속 메모리 모터(Variable Flux Memory Motor)의 특성과 감자전류 산정에 대하여 다루었다. 서론에서는 VFMM에 대한 특징 및 설계를 위한 분석 방안을 제시하였으며, 메모리모터의 동작 원리와, 정밀한 해석 방법은 본론을 통하여 자세히 다루었다. 감자전류는 프라이자흐 모델을 이용하여 초기 자석의 자화량을 비선형 적으로 구한 후 인가된 d축 전류에 따른 변화된 자화량 및 기전력 값들을 반복적인 연산을 통하여 신뢰성 있는 감자전류를 산정하였다.

• Journal of IKEEE
• /
• v.2 no.2 s.3
• /
• pp.166-172
• /
• 1998

Switched reluctance motor(SRM) has the advantages of simple structure, low rotor inertia and high efficiency. However, position sensor is essential in SRM in order to synchronize the phase excitation to the rotor Position. The Position sensors increase the cost of drive system and tend to reduce system reliability. This paper investigates the speed control of sensorless SRM in which the Phase current and change rate are utilized in position decision, and the period of dwell angle is variable for speed control. The proposed system consists of Position decision circuit, speed controller, digital logic commutator, switching angle controller and inverter The performances in the proposed system are verified through the experiment.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.5B no.4
• /
• pp.312-316
• /
• 2005

The single phase induction motor has been commonly applied to small-sized electrical appliances because of its low cost, but it has low efficiency and large torque ripple, and it is incapable of speed control. However, two-phase induction motors have small torque ripple, high efficiency and variable speed control, because they are inverter fed. In this paper, the dynamic characteristics of the two-phase induction motor, such as the torque ripple, current and speed, are analyzed by using the time-stepping finite element method, and compared with the cage-type single phase induction motor.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.5
• /
• pp.446-452
• /
• 2001

In this paper, a novel design method of variable motor inertia in Induction motor drive system is proposed. The inertia of a load and a motor are estimated by using RLS (Recursive Least Square) algorithm. The speed controller is designed by Kharitonov theory of motor. The effectiveness of the proposed scheme is verified with simulation and experiment results.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.51 no.8
• /
• pp.467-474
• /
• 2002

In this paper, a wind power simulator is designed and implemented. To realize the torque of wind blade, a DC motor is used as a variable torque input device. An induction machine is used as a generator of which speed is controlled to maintain the optimal tip speed ratio during wind speed change. Input torque of system is controlled by armature current of DC motor and speed is controlled by generator control unit using field oriented control algorithm. Various control algorithms such as MPPT, soft start up, the simulator reactive power control, can be developed and tested using the simulator.