• 신재생에너지
• /
• 제3권4호
• /
• pp.22-30
• /
• 2007

An expansion device plays an important role in optimizing the heat pumps by controlling refrigerant flow and balancing the system pressures. Conventional expansion devices are being gradually replaced with electronic expansion valves due to increasing focus on comfort, energy conservation, and application of a variable speed compressor. In addition, the amount of refrigerant charge in a heat pump is another primary parameter influencing system performance. In this study, the flow characteristics of the expansion devices are analyzed, and the effects of refrigerant charge amount on the performance of the heat pump and the variation of compressor speed are investigated at various operating conditions. Mass flow rate through capillary tube, short tube orifice, and EEV was strongly dependent on the upstream pressure and subcooling. The heat pump system is very sensitive with a variation of refrigerant charge amount. The performance of it can be optimized by adjusting the flow rate through expansion device to maintain a constant superheat at all test conditions.

• 설비공학논문집
• /
• 제10권4호
• /
• pp.495-507
• /
• 1998

The transient characteristics of a 4.0㎾ inverter driven heat pump was investigated by theoretical and experimental studies. The heat pump used in this study consists of a high side scroll compressor and $\Phi$7 compact heat exchangers with two capillary tubes. A series of tests was peformed to examine the transient characteristics of heat pump in heating and cooling mode when the operating speed was varied from 30Hz to 102Hz. One of the major issues that has not been addressed so far is transient characteristics during speed modulation. A cycle simulation model has been developed to predict the cycle performance under frequency rise-up conditions, and the results of theoretical study were compared with the results of experimental study. The theoretical model was driven from mass conservation and energy conservation equations to predict the operation points of refrigerant cycle and the performances at various operating speeds. For transient conditions, the simulated results are in good agreement with the experimental results within 10%. The transient cycle migration of the liquid state refrigerant causes a significant dynamic change in system. Thus, the migration of refrigerant is the most important factor whenever An experimental analysis is performed or A simulation model is developed.

• 전력전자학회논문지
• /
• 제11권1호
• /
• pp.1-6
• /
• 2006

본 논문에서는 유압펌프 시스템의 효율적 구동을 위한 SRM 구동시스템이 제안된다. 유압 펌프 시스템이 요구하는 최대 사용 유압 및 사용유량으로부터 적정한 용량의 SRM을 설계 및 제작하고, 시험을 위해 SRM과 제어기를 포함한 전체 유압시스템을 구성한다. 제시한 SRM 구동시스템은 효율적 구동을 위해 속도제어 뿐만 아니라 유압계통의 압력검출로부터 압력제어도 같이 행하며, 이로부터 SRM이 적정한 운전영역에서 구동되도록 한다. 2.2[KW] 12/8극 SRM과 DSP를 사용한 제어기가 설계되고, 이 시스템을 실제 유압시스템에 적용하여 운전 특성을 확인하였다. 그 결과 제안한 시스템이 고효율과 빠른 응답특성을 가짐을 알 수 있다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.741-744
• /
• 2002

The closed circuit pump is applied to control rotating speed and direction of hydraulic motor in hydrostatic transmission. To development of this pump, first of all the servo control regulator has to be designed. Mechanical-hydraulic type servo control mechanism is excellent to be compared with electronic-hydraulic type servo control valve to reliability and economy. In this paper to development positive and negative variable displacement type servo regulator, the hydro-mechanical servo control mechanism is calculated and designed with force balance of pilot piston and position feedback of servo piston.

• Journal of Electrical Engineering and Technology
• /
• 제4권4호
• /
• pp.515-520
• /
• 2009

According to the operating characteristics of pump applications, they should exhibit high efficiency and energy saving capabilities throughout the whole operating process. A novel efficiency optimization control strategy is presented here to meet the high efficiency demand of a variable speed Permanent Magnet Synchronous Motor (PMSM). The core of this strategy is the excellent integration of mended maximum torque to the current control algorithm, based on the losses model during the dynamic and the grade search method with changed step by fuzzy logic during the steady. The performance experiments for the control system of a variable speed high efficiency PMSM have been completed. The test results verified that the system can reliably operate with a different control strategy during dynamic and steady operation, and the system exhibits better performance when using the efficiency-optimization control.

• 제어로봇시스템학회논문지
• /
• 제4권4호
• /
• pp.441-447
• /
• 1998

Motivated by a recent work, a fuzzy-power-controller(FPC) is designed for the relieving-horsepower control of output variable pump with electrical proportional valve and actually implemented on the industrial excavator. In order to calculate the output power of pump with input of FPC, a linear discrete time model of load system to pump is obtained and the result is applied to control the engine-pump coupled system by software without pressure and flow sensor. The FPC controls the engine and pump coupled system by relieving horsepower control according to the change of load and the running conditions in relieving horsepower control are selected by fuzzy inference engine. A case study is peformed through the construction of the control device and installation on the excavator. It shows that the relieving-horsepower control system with the FPC, as suggested in this paper, is superior to the conventional PID controllers. And also, the excavator, with the FPC, shows that the power-loss of the coupled system is reduced and the running speed of the hydraulic actuator is enhanced.

• 제어로봇시스템학회논문지
• /
• 제3권2호
• /
• pp.162-168
• /
• 1997

Digital variable structure controller(DVSC) is implemented to control the temperature for the hot water heating circulating pump control system. For the DVSC, a control algorithm is suggested, which using a nonlinear sliding surface and a PID sliding surface outside and inside of steady state error boundary layer, respectively. Smith predictor algorithm is used for the compensation of long dead time. The DVSC of the suggested algorithm yields improved control performance compared with the one of existing algorithm. The system responses with the suggested DVSC shows good responses without overshoot and steady state error inspite of heating load change. By decreasing sampling time, dead time and rise time are increasing, and system output noise by flow dynamics is amplified.

• 한국정밀공학회지
• /
• 제25권2호
• /
• pp.49-56
• /
• 2008

In order to reduce energy consumption, secondary controlled system has been applied to many types of equipments. In lifting equipments or press machines using hydraulic cylinder, a hydraulic transformer is used as a control component instead of a valve for motion control and a component for recovering potential energy of load. The transformer is a combination of a variable displacement pump/motor as a secondary controlled element and a fixed displacement pump/motor. In this paper the effect of transformer is studied. Multiple closed loop controllers with displacement feedback of variable pump/motor, speed feedback and position feedback of cylinder are used. The efficiency and energy consumption when cylinder is driven up and down is calculated by simulation. Simulation results show that considerable energy saving is achieved by choosing load ratio, circuit type and supply pressure.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2012년도 전력전자학술대회 논문집
• /
• pp.512-513
• /
• 2012

The electric motor is essential to drive turbo machinery. In order to overcome the speed limitations of general motors, the inverter is used to perform high speed to tens of rpm. The high speed drives are widely used in many applications such as turbo blower, turbo centrifugal compressors, and pump using air bearing technique. Starting of high speed motor can cause step out, stall, oscillation of motor because the phase inductance is much smaller than that of ordinary motor. This paper studied on the starting characteristic of variable speed centrifugal chiller considering high speed motor characteristics. Finally, the superiority of the inverter is verified by experimental results.

• 한국산업융합학회 논문집
• /
• 제19권3호
• /
• pp.125-132
• /
• 2016

The swash-type piston pump is a device that discharges as much volume of hydraulic oil generated as it moves the ramp by controlling the angle of the swash. This pump is suitable for high-speed high pressurization, and due to its useful characteristic being the variable capacity-type, it is used as a main pump for heavy equipment in various fields such as defense, shipbuilding, construction, etc. This study intends to obtain optimal design values by conducting a structural analysis in order to verify its reliability during the design process of the newly developed swash-type piston pump.