• Journal of the Korean Society of Clothing and Textiles
• /
• v.17 no.1
• /
• pp.151-161
• /
• 1993

The purpose of this study was to investigate the effect of hydrophilic finish for polyester (PET) fabric and hydrophobic finish for cotton fabric on the water transport and comfort properties. Polyester fabric was treated with 10% sodium hydroxide solution to impart hydrophilicity. Cotton fabric was sprayed with Scotch-gard$^{(R)}$ water and oil repellent finish to impart hydrophobicity. Porosity, air permeability, contact angle, wickability and water vapor transport rate (WVTR) were measured to determine the water transport properties of fabrics. To compare the comfort properties of treated and untreated fabrics, wear test was performed by putting fabric patches on the upper back: stratum corneum water content (SCWC), subjective wettedness and comfort rating were determined. The results were as follows: (1) The contact angle of water on treated polyester fabric was decreased and that of treated cotton fabric was increased. Also, the wickability of treated polyester fabric was increased and the wickability of cotton fabric was decreased. (2) Although each finish did not change porosity, the water vapor transport rate of treated polyester fabric was increased and that of treated cotton fabric was decreased slightly. (3) The results of stratum corneum water content measurements showed good agreement with the results of the contact angle and the wickability, i.e., the better the liquid water transport properties are, the less the stratum corneum water contents were resulted. (4) The realtionship of subjective wettedness or comfort and stratum corneum water content was independent. Therefore, it was concluded that human perception on the subjective wettedness or the comfort is affected by the skin contact of wet fabric rather than by the stratum corneum water content.

• Membrane Journal
• /
• v.2 no.1
• /
• pp.21-32
• /
• 1992

Hydrogen-permselective silica membranes were synthesized within tim walls of porous Vycor tubes by chemical vapor depostion of $SiO_2$. Film deposition was carried out using $SiCl_4$ hydrolysis either in the oppm shag reactants or in the one-sided geometry. At temperatures above $600^{\circ}C$ the permeation rate of hydrogen thorough the silica films varied between 0.01 and $025cm^3(STP)/cm^2-min-atm$ depending on the reaction geometry and the $H_2 : N_2$ permeation ratio was about 1000. Permeation rates of both $H_2$ and $N_2$ increased with increasing temperature. The silica membranes produced by one-sided deposition have higher hydrogen permmeation rates than those produced by the opposing reactants geometry although the membranes formed in an opposing reactants geometry were relatively stable during the heat treatment or after exposure to ambient air. These membranes can be applied to high temperature gas separations or membrane reactors once the film deposition process is optimized to get high permeability as well as good stability.

• Textile Coloration and Finishing
• /
• v.34 no.1
• /
• pp.68-75
• /
• 2022

The breathable film refers to a high-functional film that allows gas and water vapor to pass through very fine and sophisticated pores but not liquid. In this research, the breathable film was prepared based on linear low-density polyethylene (LLDPE) and CaCO₃ particles by extrude method. The LLDPE composite film containing CaCO₃ particles had excellent mechanical properties and functionalties. The drawing is a technologically simple and excellent method for improving the mechanical properties of composite films. In this work, the effects of draw ratio on morphology, crystallinity, pore size distribution, mechanical properties, and water vapor permeability of the films were examined. The results revealed that both surface morphology and breathability were affected by the influence of chain orientation and crystal growth with increasing the draw ratio. The mechanical properties were improved with increasing the draw ratio.

• Journal of Soil and Groundwater Environment
• /
• v.20 no.1
• /
• pp.1-6
• /
• 2015

The objectives of this study were to calculate the radius of influence (ROI) of well for an air-sparging (AS)/soil vapor extraction (SVE) system and to evaluate the applicability of the system applied for the remediation of the petroleum contaminated rail site. For air permeability test, three monitoring wells were installed at a location of 1.3 m, 2.3 m, 3.0 m from the extraction well. And the pressure of each monitoring well was measured by extracting air from the extraction well with the pressure and flow of $(-)2,600mmH_2O$ and $1.58m^3/min$. The ROI for an extraction well was calculated as 4.31 m. Air was injected into the injection well with the pressure and flow of $3,500mmH_2O$ and $0.6m^3/min$ to estimate the radius of influence for oxygen transfer. Oxygen concentrations of air from three monitoring wells were measured. The ROI of an injection well for oxygen transfer was calculated as 3.46 m. The 28 extraction wells and 19 injection wells were installed according to the ROI calculated. The AS/SVE system was operated eight hours a day for five months. The rail site was contaminated with the petroleum and concentrations of benzene, toluene, and xylene were over the 'Worrisome Standard' of the 'Soil Environment Conservation Act'. The contaminated area was estimated as $732m^2$ and contaminants were dispersed up to (-)3 m from the ground. During the operation period, soil samples were collected from 5 points and analyzed periodically. With the AS/SVE system operation, concentrations of benzene, toluene, and xylene were decreased from 7.5 mg/kg to 2.0 mg/kg, from 32.0 mg/kg to 23.0 mg/kg, from 35.5 mg/kg to 23.0 mg/kg, respectively. The combined AS/SVE system applied to the rail site contaminated with volatile organic compounds (VOCs) exhibited a high applicability. But the concentration of contaminants in soil were fluctuated due to the heterogeneous of soil condition. Also the effect of the remediation mechanisms was not clearly identified.

• Preventive Nutrition and Food Science
• /
• v.10 no.1
• /
• pp.88-91
• /
• 2005

To improve the physical properties of protein films, various plasticizers and cross-linking agents were used in the preparation of the films. For zein film, 3% polypropylene glycol with 3% glycerol was the best plasticizer, while 2.5% glycerol was the most suitable for soy protein isolate (SPI) film in terms of tensile strength (TS), % elongation, and water vapor permeability (WVP). Formaldehyde, glutaraldehyde, glyoxal, and cinnamaldehyde as cross-linking agents of protein films were used to further improve the physical properties of the films. All aldehydes used as cross-linking agent in this study improved TS of zein and SPI films. In particular, cinnamaldehyde was the best cross-linking agent due to its safety in foods. These results suggest that appropriate use of plasticizer and cross-linking agent like cinnamaldehyde should improve the physical properties of protein films for use in food packaging.

• Food Science of Animal Resources
• /
• v.36 no.3
• /
• pp.421-426
• /
• 2016

Polylactic acid (PLA) is a biodegradable and renewable polymer, which represents a valuable alternative to plastic packaging films, often associated with environmental problems. In this study, we tested the suitability of PLA as a biodegradable packaging film and assessed the antimicrobial activity of lemongrass oil (LO), incorporated into the PLA film in different concentrations. To obtain the optimal physical properties for PLA films, tensile strength, elongation at break, and water vapor permeability were measured under different preparation conditions. In addition, the antimicrobial activity of the LO contained in the PLA film against Listeria monocytogenes was investigated by disc diffusion and viable cell count. Among all concentrations tested, 2% LO was the most suitable in terms of antimicrobial activity and physical properties of the PLA film. Based on these results, we used the PLA film containing 2% LO to pack pork sausages; after 12 d of storage at 4℃, the population of inoculated L. monocytogenes in the sausage samples wrapped with the PLA film containing 2% LO was reduced by 1.47 Log CFU/g compared with the control samples. Our data indicate that PLA films containing 2% LO represent a valuable means for antimicrobial sausage packaging.

• Food Science of Animal Resources
• /
• v.37 no.5
• /
• pp.635-645
• /
• 2017

In this study, effect of transglutaminase (TGase) addition on physical, water barrier, optical and mechanical properties of mechanically deboned chicken meat protein (MDCM-P) films was investigated. When TGase was added to the films, the thickness increased, but the solubility decreased. Films treated with TGase exhibited higher water vapor permeability than control film (p<0.05). When TGase concentration increased, the $L^*$ values of films decreased, but $a^*$ and $b^*$ values increased. All films showed very good barrier properties against UV light. The highest tensile strength was obtained in MDCM-P films containing 3% TGase (p<0.05). The elongation at break values increased with the TGase concentration increasing from 1 to 3%, but decreased at higher enzyme concentration (p<0.05). The addition of TGase altered molecular organization and intermolecular interaction in the film matrix. TGase treated films showed smoother and ordered surface structure and homogeneous and compact microstructure. The results indicated that TGase use can be an effective approach in improving the solubility and mechanical properties of MDCM-P films.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.162-162
• /
• 2016

We present multifunctional indium tin oxide (ITO) thin films formed at room temperature by a normal sputtering system equipped with a plasma limiter which effectively blocks the bombardment of energetic negative oxygen ions (NOIs). The ITO thin film possesses not only low resistivity but also high gas diffusion barrier properties even though it is deposited on a plastic substrate at room temperature without post annealing. Argon neutrals incident to substrates in the sputtering have an optimal energy window from 20 to 30 eV under the condition of blocking energetic NOIs to form ITO nano-crystalline structure. The effect of blocking energetic NOIs and argon neutrals with optimal energy make the resistivity decrease to $3.61{\times}10-4{\Omega}cm$ and the water vapor transmission rate (WVTR) of 100 nm thick ITO film drop to $3.9{\times}10-3g/(m2day)$ under environmental conditions of 90% relative humidity and 50oC, which corresponds to a value of ~ 10-5 g/(m2day) at room temperature and air conditions. The multifunctional ITO thin films with low resistivity and low gas permeability will be highly valuable for plastic electronics applications.

• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.365-370
• /
• 2001

There are various wick types for heat pipe. In the present study, the manufacturing technology of a sintered wick among various wick types is discussed. The sintering technology using metal has been applied broadly in the field of electronic-telecommunication as well as heat pipes. A study of manufacturing procedure and characteristic of sintered wick for heat pipe have been performed. Copper powder was used as wick material and stainless steel as a mandrel. A manufacturing technology of the mandrel for arranging vapor core in heat pipe, a sintering technology by first or second times and operating temperature for sintering, the measurements of a porosity, pore size, and pore distribution of sintered wick were considered. In the meantime, a heat pipe with sintered wick has been manufactured and a performance test of the heat pipe has been performed in order to review cooling performance. The performance test results for the 4mm diameter heat pipe with the sintered wick shows the stability since the temperature difference between a evaporator and a condenser of the heat pipe is less than $4.4^{\circ}C$, and thermal resistance is less than $0.7^{\circ}C/W$.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.39 no.5
• /
• pp.778-788
• /
• 2015

This study evaluated the characteristics and sensibility of work clothes materials developed that took into account the work environment of major industrial settings, for which a selection was made according to spring/autumn use and winter use. The physical properties of the existing and test weaving of the work clothes materials were compared after the test weaving of work clothes materials through material design, which altered the yarn count, composition, weave and density of material. To evaluate sensibility of work clothes materials subjectively, seven ranks' semantic differential scale questions were developed with polar adjective pairs. The test weaving of work clothes materials showed improved performance (such as tensile strength, dimensional change, water vapor permeability, and color fastness) compared to the existing materials. The common factor analysis indicated that the explanatory power of the cumulative variance for the spring/autumn use and winter use was 71.19% and 69.53%, respectively.